Mitsubishi Electric AJ65BT-D62 Manuel utilisateur

User's Manual

(Hardware)

AJ65BT-D62

AJ65BT-D62D

AJ65BT-D62D-S1

Thank you for purchasing the Mitsubishi programmable controller

MELSEC-A series.

High-Speed

Counter Module

Prior to use, please read this and relevant manuals thoroughly to

fully understand the product.

MODEL AJ65BT-D62-U-H-E

MODEL

CODE 13JL44

IB(NA)-66822-G(1806)MEE

A-1

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals

carefully and pay full attention to safety to handle the product correctly.

In this manual, the safety precautions are classified into two levels:

" WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under

" CAUTION" may lead to serious consequences.

Observe the precautions of both levels because they are important for personal

and system safety.

Make sure that the end users read this manual and then keep the manual in a safe

place for future reference.

[Design Precautions]

WARNING

●If data link becomes faulty, the status of the faulty station changes as follows.

Using the communication status information, construct an interlock circuit in

the sequence program so that the system operates safety.

There is a risk of an accident due to output error or malfunction.

(1) All general-use inputs from this module turn off.

(2) All general-use outputs from this module turn off.

●The inputs and outputs may be turned on or off when a failure occurs within

the module. Provide a circuit that externally monitors the input and output

signals that might lead to a serious accident.

WARNING

Indicates that incorrect handling may cause

hazardous conditions, resulting in death or severe

injury.

Indicates that incorrect handling may cause

hazardous conditions, resulting in minor or moderate

injury or property damage.

CAUTION

A-2

[Design Precautions]

[Installation Precautions]

[Wiring Precautions]

CAUTION

●Do not have control cables and communication cables bundled with or placed

near by the main circuit and/or power cables.

Wire those cables at least 100mm (3.94 inch) away from the main circuit

and/or power cables.

Not doing so could result in noise that would cause erroneous operation.

CAUTION

●Use each module in an environment as specified in the "general specification"

in the detailed manual.

Usage of the module outside the general specification range may cause

electric shock, fire, malfunction, product damage or deterioration.

●Tighten the module securely using DIN rail or installation screws within the

specified torque range of the installation screws. Loose screws may cause

falling or malfunction. Also, if the screws are too tight, it may cause falling or

malfunction due to damage of the screws or module.

●Do not touch the conductive area of the module.

Doing so may cause module malfunction or breakdowns.

WARNING

●Perform installation and wiring after disconnecting the power supply at all

phases externally.

If the power is not disconnected at all phases an electric shock, product

damage or malfunction may result.

●When powering up or operating the module after performing installation or

wiring work, always attach the terminal cover that came with the product.

It may cause an electric shock if the terminal cover is not attached.

A-3

[Wiring Precautions]

[Starting and Maintenance Precautions]

CAUTION

●Be sure to ground the FG terminal to the class-3 or higher grounding.

Otherwise there will be a danger of malfunctions.

●Use applicable solderless terminals and tighten them with the specified

torque. If any solderless spade terminal is used, it may be disconnected when

the terminal screw comes loose, resulting in failure.

●Perform correct wiring for the module according to the product's rated voltage

and terminal arrangement. Connecting to a power supply different from rating

or mis-wiring may cause fire and/or product failure.

●Fix terminal screws securely within the specified torque range. Loose terminal

screws may cause short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short

circuit, or malfunction.

●Make sure foreign objects do not get inside the module, such as dirt and wire

chips. It may cause fire, product failure or malfunction.

●Be sure to fix the wires or cables that are connected to the module in place,

either by running them through a duct or by using clamps.

If the cables are not fixed in one of these ways, dispersion, movement, or

careless pulling of the cables may cause damage to the module or

malfunction due to cable contact faults.

●Do not install the control lines together with the communication cables, or

bring them close to each other. Failure to do so may cause malfunctions due

to noise.

●When disconnecting a communication or power supply cable from the

module, do not pull on the cable itself.

Disconnect cables fitted with connectors by holding and pulling the cable

connector. Disconnect cables not fitted with a connector by removing the

screws from the part connected to the module.

Pulling on a cable that is connected to the module can cause damage to the

module or cable, or malfunction due to cable connection faults.

WARNING

●Do not touch the terminals when the power is on. It may cause an electric

shock or malfunction.

●Perform cleaning the module after turning off the all external power supply for

sure. If you do not switch off the external power supply, it will cause electric

shock.

A-4

[Starting and Maintenance Precautions]

[Disposal Precautions]

CAUTION

●Never try to disassemble or modify module. It may cause product failure,

malfunction, fire or cause injury.

●Do not drop or apply strong shock to the module case. Failure to do so may

damage the module.

●Make sure to switch all phases of the external power supply off before

installing or removing the module to/from the panel.

If you do not switch off the external power supply, it will cause failure or

malfunction of the module.

●Always set the setting pins for pulse and external input voltage after externally

shutting down all phases of the power supply.

Failure to shut down all phases of the power supply may cause a failure or

malfunction of the module.

●Do not install/remove the terminal block more than 50 times after the first use

of the product. (IEC 61131-2 compliant)

CAUTION

●When disposing of the product, treat it as industrial waste.

A-5

A-6

A-7

A-8

A-9

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in

conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any,

shall not lead to any major or serious accident; and

ii) where the backup and fail-safe function are systematically or

automatically provided outside of the PRODUCT for the case of any

problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of

being used in general industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY

(INCLUDING, BUT NOT LIMITED TO ANY AND ALL RESPONSIBILITY

OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT, PRODUCT

LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR

DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE

OPERATED OR USED IN APPLICATION NOT INTENDED OR

EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING

CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY

MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the

PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT

in;

• Nuclear Power Plants and any other power plants operated by Power

companies, and/or any other cases in which the public could be

affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases

in which establishment of a special quality assurance system is

required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport

equipment such as Elevator and Escalator, Incineration and Fuel

devices, Vehicles, Manned transportation, Equipment for Recreation

and Amusement, and Safety devices, handling of Nuclear or

Hazardous Materials or Chemicals, Mining and Drilling, and/or other

applications where there is a significant risk of injury to the public or

property.

Autres manuels pour AJ65BT-D62

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mitsubishi Electric Unité de contrôle

Mitsubishi Electric

Mitsubishi Electric EMU4-CNT-MB Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric QD75P1N Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65SBTB2N-16S Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric QJ71DN91 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65BT-D62 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q64AD2DA Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R AnyWireASLINK Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric NZ2GF2B-60TCTT4 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric L61P Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65FBTA2-16TEU Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EMU4-CNT-MB Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PAC-SV01PW-E Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65BT-D75P2-S3 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC-L LD75P Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric A1SJ71AP23Q Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC-QS Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FX2N-32CAN Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric NZ2GF-ETB Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PSS**S72FT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric NZ2FTGN Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur