Mitsubishi Electric LMAP02-E Manuel utilisateur

Building Air-Conditioners Control System
Model : LMAP02-E
Contents
Safety precautions ……………………………………1,2
1.Parts Inclue ……………………………………………3
2.Specifications …………………………………………3
2-1 External View……………………………………3
2-2 Enviroment Specifications ……………………3
2-3 Connected Air Conditioning Equipment ……4
2-4 LONWORKS®Network Specifications …………4
2-5 Variables of LM-AP network …………………5
3.Installation ……………………………………………6
3-1 Locally Procured Parts …………………………6
3-2 Securing the Unit ………………………………7
3-3 Connection Methods……………………………8
3-4 Electrical Wiring…………………………………9
4.Sysyem Settings ……………………………………10
4-1 If not used together with MELANS …………10
4-2 If used together with MELANS ………………11
4-3
Initialization Settings of LONWORKS®Network
…12
5.Confirming Operation ………………………………13
5-1 Pre-operation preparations and settings ……13
5-2 Test-operation procedure ……………………13
6.Troubleshooting ……………………………………14
6-1 Abstract…………………………………………14
6-2 Troubleshooting ………………………………15
6-3 Error Code list …………………………………15
Before using the unit, please read this Installation
Manual carefully to ensure correct operation. Store this
Installation Manual in a location that is easy to find.
Echelon®,LON®,LONWORKS®,Neuron®,3150®and the
Echelon logo are trademarks of Echelon Corporation
registered in the United States and other countries.
LonMaker™ and the Lon Users logo are trademarks of
Echelon Corporation.
Installation Manual
AIR CONDITIONER INTERFACE

Safety Precautions

• Before instralling this unit,make sure you read all the “Safety Precautions”.

• This manual describes the installation of LM-AP and wiring to the outdoor unit.

• Please look at the installation manual of an air-conditioning unit about the installation method of an air-conditioning unit.

• The “Safety Precautions” provide very important points regarding safety. Make sure you follow them.

Symbols and Terms

Statements identify condition or practices that could result in personal injury or loss of life.

Statements identify condition or practices that could result in damage to the unit or other

property.

Symbols used in the illustrations

: Indicates a part which must be grounded.

: Indicates that the main switch must be turned off before servicing.

(This symbol is displayed on the main unit label.) <Color: Blue>

: Beware of electric shock.(This symbol is displayed on the main unit label) <Color: Yellow>

: Please pay attention to electric shock fully because this is not Safety Extra Low-Voltage (SELV)

circuit.

And at servicing,please shut down the power supply for LM-AP.

WARNING

CAUTION

Ask your dealer or technical representative to install.

Any deficiency cased by your own installation may result in an

electric shock and fire.

Ensure that installation work is done correctly following

that installation manual.

Any deficiency caused by installation may result in an electric

shock or fire.

Install in a plase which is strong enough to withstand the

weight of the unit

Any lack of the strength may cause the unit to fall down,

resulting in a personal injury.

Any deficiency caused by installation may result in an electric

shock, fire or incorrect operation.

All electrical work must be performed by a licenced

technician, according to local regulations and the

instructions given in this manual.

Any lack of electric circuit or any deficiency caused by

installation may result in an electric shock or fire.

Wire and connect using the desired cables securely so

that any external force from the cable is imparted to the

terminal connections.

Imperfect connection and fixed may result in heading or fire.

Securely install the cover (panel) of the LM-AP.

If the cover (panel) is not installed properly, dust or water may

enter the unit and fire or electric shock may result.

Never modify or repair the unit by yourself.

Any deficiency caused by your modification or repair may

result in an electric shock or fire. Consult with your distributor

for repair.

Do not move and re-install the unit yourself.

Any deficiency caused by installation may result in an electric

shock or fire. Ask your distributor or special vender for moving

and installation.

Make sure that the unit is powered by dedicated line.

Other appearance connected to the same line could cause an

overload.

Make sure that there is a main power switch.

A ready accessible breaker for power source line helps

reduce the risk of electric shocks.Installation of a breaker is

mandatory in same areas.

If it is assumed that moisture advances into the unit,

such as the time of rainy weather, do not do check or

work of an electric circuit.

It may become the cause of damage of a fire and the unit by

an electric shock or corrosion.

• After reading this installation manual, keep it in a place where the final user can see it anytime he or she wants to it.

When someone moves, repairs or uses the LM-AP, make sure that this manual is forwarded to the final user.

CAUTION

Do not install the unit where combustible gas may leak.

If the gas leaks and accumulates around the unit, an

explosion may result.

Do not use in any special environment.

Using in any place exposed to oil(including machine oil),

steam and sulfuric gas may deteriorate the performances

significantly or given damage to the component parts.

When installing the unit in a hospital, communication

station, or similar place, provide sufficient protection

against noise.

The inverter equipment, private power generator, high-

frequency medical equipment, or radio communication

equipment may cause the air conditioner to operate

erroneously, or fail to operate. On the other hand, the air

conditioner may affect such equipment by creating noise that

disturbs medical treatment or image broadcasting.

Do not wash with water.

Doing so may cause an electric shock or a malfunction.

Do not install in any steamy place such as bath room or

kitchen.

Avoid any place where moisture is condensed into dew.

Doing so may cause an electric shock or a malfunction.

Do not touch any PCB(Printed Circuit Board) with your

hand or tools. Do not have dust collected on the PCB.

Doing so may cause an electric shock or fire.

Do not install in any place where acidic or alkaline

solution or special spray are other be used.

Doing so may cause an electric shock or a malfuction.

Do not install in any place at a temperature of more then

43 ˚C or less than -15˚C.

It may become the cause of modification and failure.

Safety dispose of the packing materials.

Tear apart and throw away plastic packaging bags so that

children will not play with them. If children play with a plastic

bag which was not torn apart, they face the risk of suffocation.

Be sure to shut off the power source of the unit and all

the other unit to connected to the unit before wiring.

Doing so may cause an electric shock or a malfunction.

Use only an earth leakage breaker and fuse of the

specified capacity.

If no earth leakage breaker is installed, it may cause an

electric shock.

Using fuse and wire or copper wire with too large capacity

may cause a malfunction of unit or fire.

A power-supply line and a transmission line do not band

together, or are not contained in the same metal pipe.

Doing so may cause a malfunction of unit.

This appliance must be earthed.

Make sure to install a protective earth(PE) line. Do not

connect the protective earth line to gas or water pipes,

lightning conductors or telephone grounding lines. Improper

grounding may cause an electric shock.

Wire so that it dose not received any tension.

Tension may caused wire breakage, heating or fire.

Use standard wires in compliance with the current

capacity.

A failure to this may result in an electric leakage, heating or

fire.

Never connect the power source to the transmission line.

Doing so may caused a malfunction or a failture.

Do not touch the switches with wet fingers.

Touching a switch with wet fingers can cause electric shock.

1. Parts Include

2. Specifications

Verify that the following parts are appended to the product.

2-2 Environment Specifications

2-1 External View

Name

Shape

Quantity

Main Unit Binding band

Installation manual

· The external interface file (XIF) is necessary for the product.

Upon verifying the 16-digit program ID (PID) which is bonded on the board, please contact your dealer.

7.5

ø10

4.5

9.6 59.6

Detail of A

340

325

60240

360A

TB1

Power supply terminal

( ~ 200 - 240V)

2-ø4.5 hole TB2

M-NET transmission terminal TB21

LONWORKS®transmission terminal

Item

Power Source

Current Consumption

Dimensions

Net Weight

Operation

Environment

Installation Environment

Description

~ 220 - 240V (50/60 Hz)

50 mA (Maximum)

340 (H) x 360 (W) x 59.6 (D) mm

3.3 kg

Temperature Operating Range

Storage Range

Humidity In the control box

30 to 95 RH (No condensation)

-15 to 43˚C

-20 to 60˚C

2-3 Connected Air Conditioning Equipment

2-4 LONWORKS®Network Specifications

* The proper communication is not obtainable when communication intervals exceed its performance,

assure sufficeint intervals.

* ACK Service is recommended for the network service.

* Detailed specifications for the LONWORKS®network can be found in “ FTT-10A Free Topology Transceiver

User's Guide ” by Echelon Corporation.

Item Description

Connected Equipment

Number of Units LM-AP can control 50 indoor units (including LOSSNAY)

Item Description

TMPN3150 (10MHz)

Neuron CHIP

FTT-10A (Free Topology 78kbps)

Network Transceiver

Performance 2.5 inputs/second

Average communication capacity

50 inputs/second (for one second)

Peak communication capacity

MITSUBISHI ELECTRIC Multiple split type air conditioners CITY MULTI

Split-type air conditioners Mr.SLIM

Heat recovery ventilators LOSSNAY

(* For details of the connected models, please contact the dealer.)

2-5 Variables of LM-AP network

The following are applied to the CITY-MULTI type indoor unit of the Multiple split type air conditioners CITY MULTI.

If Mr.SLIM or LOSSNAY is used, refer to the technical guide for the details of the network variables.

Request Local

Prohibit SetPoint

Request Local

Prohibit mode

Request Local

(note3,4)

(note3)

Prohibit On/Off

Local Prohibit

mode state

Local Prohibit

SetPoint state

Local Prohibit

On/Off state

Request On/Off

Request Mode

Setpoint from network

(Both cool and heat)

Request Fanspeed

nviOnOff_n

nv1n

nviMode_n

nv3n

nviSetPoint_n

nv5n

nviFanSpeed_n

nv7n

nviProOnOff_n

nv19n

nviProMode_n

nv21n

nviProSetPoint_n

nv23n

nvoOnOff_n

nv2n

nvoMode_n

nv4n

nvoSetPoint_n

nv6n

nvoFanSpeed_n

nv8n

nvoThermo_n

nv10n

nvoSpaceTemp_n

nv12n

nvoAlarm_n

nv16n

nvoProOnOff_n

nv20n

nviProMode_n

nv22n

nviProSetPoint_n

nv24n

Alarm state

Temperature state

of indoor

Thermo On/Off state

FanSpeed state

Setpoint state

(both cool and heat)

Mode state

On/Off run state

(note1) The case of CITY MULTI is indicated.

(note2) There is a case which cannot be used with the system configuration of the air conditioners units.

(note3) “n” of the network variable shows indoor unit address (M-NET).

(note4) It is possible to use when the “MA” remote controler.

Network Variables

Fanction

Local Prohibit SetPoint state

Local Prohibit On/Off state

Local Prohibit mode state

Alarm state

Temperature state of indoor

Thermo On/Off state

FanSpeed state

Setpoint state(both cool and heat)

Mode state

On/Off run state

Request All Off

Request Local Prohibit SetPoint

Request Local Prohibit mode

Request Local Prohibit On/Off

Request Fanspeed

Setpoint from network(Both cool and heat)

Request Mode

Request On/Off

Operation

Monitor

Item

3. Installation

<Notes>

Prepare the following prior to installing the unit.

Read and understand the contents of Chapter 1 “Safety Precautions ” before performing the installation.

3-1 Locally Procured Parts

Contents

Power wire

and ground wire

M-NET

transmission wire

Screw To install the main body, prepare four M4 screws which are suitable for the installation area.

Use a breaker with a contact distance of 3mm or more.

Switch

Locally procured parts

Use the sheathed vinyl cord or wire.

Wire type ……… Waie is not lighter than light poly vinyl

<hloride sheathed flexible cord according to IEC 227

(designation H03 VV-F or H03 VVH2-F)>

Wire size ……… 0.75mm2to 1.25mm

Use the sheathed vinyl cord or wire.

Wire type ……… CREVS, CVVS or equivalent"

Wire size ……… Solid wire : ø1.2mm to ø1.6mm

Twist type : 1.25mm2to 2mm2

Use the wire which is recommended by Echelon Corporation.

For details, refer to “FTT-10A Free Topology Transceiver User's Guide”.

For reference, Cable Types and Txpical Parameters.

LONWORKS®Network

transmission wire

Cable type

Switch

Capacity Fuse

3A 3A

Breaker for wiring

Breaker for Current Leakage

3A 3A 30mA

0.1 sec or less

Wire

dia /AWG Rloop

Ω/km

nF/km Vprop

% of C

Belden 85102, single twisted pair,

standed 19/29, unshielded, 150˚C

Belden 8471, single twisted pair,

standed 19/29, unshielded, 60˚C

Level IV 22AWG, twisted pair,

typically solid & unshielded

JY(St) Y 2X2X0.8, 4-wire herical twist,

solid, shielded

TIA568A category 5 24AWG, twisted pair

If a shielded cable is used, the shield should be connected to earth ground via a single 470kΩ,

1/4 Ωatt, ≤10%, metal film resistor to prevent static charge build-up.

106

168

1.3mm/16

0.65mm/22

0.8mm/20.4

0.51mm/24

3-2 Securing the Unit

• When installing the product, assure a space enough to install and remove the cover of the main body.

• Use M4 screws as shown in Fig. below to fix the product.

To prevent the product from dropping, make sure to fix four places.

CAUTION • This unit does not have a water-resistant design. Always install the unit indoors or

inside a control panel.

• Install in an area capable of withstanding a 3.3 kg load.

20 20

2020

Installation space

3-3 Connection Methods

Use wire clamps provided to secure the wires and prevent external force from being conveyed by the wire to

the wire connections.

* External force could cause deformation or damage to the terminal blocks.

Use a small screwdriver to connect diameter 0.2 to 2.5 mm2(AWG24 to 12) cable for

terminal block (TB21) on the unit. Tightening torque is 0.5 to 0.6 Nm. Up to two wires can

be connected to one terminal block.

20mm

80mm

8mm Binding band

For LONWORKS®transmission wire

P.B.

L.B.

LON TB21

CN405

CN65

CN45

CN32

CN21

CN71

CN31

CN33

CNS3

CN605

CNL12

CN702

TB21

Connect LONWORKS®signal wire

to “1”, “2” or “3”, “4” of signal wire

terminal block (TB21).

• TB21-“1” and “3” as well as “2”

and “4” of TB21 are connected

inside the circuit board.

Connect the power supply

wires and ground wire to

“L”, “N” and ground of

terminal block (TB1).

Connect M-NET signal wire to “A”

and “B” of terminal block (TB2).

• Connect the M-NET

transmission wire to

transmission terminal block

(TB7) of the central control.

Attach the appended binding band to the power wire and transmission wire, and fasten it, positioning the

area at inner side than the wire clamp.

Make sure that the ground wire is longer than the other wires.

Note1

Binding band

Ground wire Power wire 35mm

M-NET 20mm

For power wire and M-NET transmission wire

Note1

P.B.

L.B.

TB1

Breaker 3A

Unit Body

CN31

313

AC250V

2A F

ZNR2

CN33

DSA1

ZNR1

Unit Body

CN71

SWL

(Service

Switch)

(Service

LEDL

LED)

CN45

CN65

1CN21

1CN32

CNL12

CN605

LED402

(5VM)

LED502

(3150RST)

M-NET

Power Supply

CN40

(WDT)

LED009

LED201

CN41 (18007RST)

SW71

(Termination Switch)

OFF

312

TO M-NET transmission line

(Centralized control line)

CNS3

AB TB2

CN405

CN702 1

Unit Body

LONWORKS® transmission line

TB21

12 4

SW4

101

OFF

ON OFF

SW2

SW1

SW3

OFF

SWU1

(1st digit)

SWU2

(2nd digit)

LED001

LED002

LED003

LED004

(Wink)

Power supply

220-240V~/N 50/60Hz

3-4 Electrical Wiring

Explanation of function switch

SW1-1 ON

OFF

Function switch

of local prohibit local prohibit effective

local prohibit invalidity

OFF

LOSSNAY is operation

fromLONWORKS®

LOSSNAY interlocks

with the indoor unit

Switch name Function

OFF

Factory

setting

Operation local prohibit nv inputfrom

ORKS®becomes Effective when switch ON.

Operation local prohibit nv input from

ORKS®becomes invalid when switch OFF.

Note

Before turning

on the power supply

SW1-5 Function switch

of LOSSNAY OFFPlease turn on the switch when LOSSNAY

is operation from LONWORKS®.

Please turn off the switch when LOSSNAY

interlocks with the indoor units.

Before turning

on the power supply

OFF

Mr.SLIM is operation

fromLONWORKS®

Mr.SLIM is not operation

fromLONWORKS®

SW1-6 Function switch

of Mr.SLIM OFF

Before turning

on the power supply

OFF

ON(test run) is transmitted

to the indoor units

OFF is transmitted to the

indoor units

SW1-9 Indoor units

test run switch OFF Always

OFF

Connected cancellation

command is transmitted

to the indoor units

None

SW3-2 Initialization

switch of the air

conditioners units

OFF Always

SW1-3 ON

OFF

Indoor temperature

state interval switch

Transmission interval

(1minutes or more)

Transmission interval

(10 minutes or more)

OFF

Before turning

on the power supply

SW1-2 ON

OFF

Used together

with MELANS switch used together with MELNAS

not used together with MELNAS

OFF

Before turning

on the power supply

Set timingSW

*number of indoor unit should

be connected 30 or less

Please turn on the switch when Mr.SLIM

is operation from LONWORKS®.

Transformer

Switch Function selection

M-NET address switch

Tremination selection switch

(LONWORKS®)

SYMBOL EXPLANATION

Power circuit boardP.B

L.B LM-AP main board

SWU1, 2 Service switch (LONWORKS®)SWL

Fuse AC250V 2A F

NAMESYMBOL

SW1, 2, 3

T1.2

SW71

LONWORKS®transmission line

Earth terminal

M-NET transmission line

Power source

LED

TB21 Power Supply switch connectorCN40/CN41

TB2

TB1

Maintenance LED

Use LED001 as Wink

(

ORKS

) at SW2-1 ˜6 OFF

LED001 ˜004

Status LED

LED009/201/502/402

Service LED (LONWORKS®)LEDL

NAMESYMBOL

Terminal

block

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mitsubishi Electric Système de contrôle

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric M700V Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Manuel du propriétaire

Mitsubishi Electric

Mitsubishi Electric BAC-HD150 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric E70 Series Manuel d'instructions

Mitsubishi Electric

Mitsubishi Electric MDS-E Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric CNC 700 Series Manuel d'instructions

Mitsubishi Electric

Mitsubishi Electric C80 Series Guide de configuration

Mitsubishi Electric

Mitsubishi Electric AG-150A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric M800W Series Guide de configuration

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric GB-24A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AG-150A-A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PAC-YT32PTA Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PAC-YG81TB Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AG-150A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAR-40MAA Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric TW-50A Guide rapide

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAR-40MAAU Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric M80 Series Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur