Mitsubishi Electric C80 Series Guide de configuration

Introduction

This manual covers the items required for installing, connecting and setting up the C80.

Read this manual thoroughly and understand the product's functions and performance before starting to use.

This manual is written on the assumption that all optional functions are added, but the actually delivered device may

not have all functions.

The unit names, cable names and various specifications are subject to change without notice. Please confirm these

before placing an order.

Be sure to keep this manual always at hand.

Notes on Reading This Manual

(1) This manual explains general parameters as viewed from the NC.

For information about each machine tool, refer to manuals issued from the machine tool builder.

If the descriptions relating to "restrictions" and "allowable conditions" conflict between this manual and the

machine tool builder's instruction manual, the later has priority over the former.

(2) This manual is intended to contain as much descriptions as possible even about special operations.

The operations to which no reference is made in this manual should be considered "impossible".

For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by

the machine tool builder takes precedence over this manual.

Items that are not described in this manual must be interpreted as "not possible".

This manual is written on the assumption that all the applicable functions are included.

Some of them, however, may not be available for your NC system.

Refer to the specifications issued by the machine tool builder before use.

For information about each machine tool, refer to manuals issued from the machine tool builder.

Some screens and functions may differ depending on each NC system (or version), and some functions

may not be possible. Please confirm the specifications before starting to use.

Do not connect NC system to the Internet-connected network.

To maintain the safety of the NC system against unauthorized access from external devices via the

network, take appropriate measures.

Also refer to the manuals on "Manual List" as necessary.

CAUTION

Manual List

Manuals related to M800/M80/E80/C80 Series are listed as follows.

These manuals are written on the assumption that all optional functions are added to the targeted model.

Some functions or screens may not be available depending on the machine or specifications set by MTB. (Confirm the

specifications before use.)

The manuals issued by MTB take precedence over these manuals.

Manual IB No. Purpose and Contents

M800/M80/E80 Series

Instruction Manual IB-1501274 Operation guide for NC

Explanation for screen operation, etc.

C80 Series

Instruction Manual IB-1501453 Operation guide for NC

Explanation for screen operation, etc.

M800/M80/E80/C80 Series

Programming Manual

(Lathe System) (1/2)

IB-1501275 G code programming for lathe system

Basic functions, etc.

M800/M80/E80/C80 Series

Programming Manual

(Lathe System) (2/2)

IB-1501276 G code programming for lathe system

Functions for multi-part system, high-accuracy function, etc.

M800/M80/E80/C80 Series

Programming Manual

(Machining Center System) (1/2)

IB-1501277 G code programming for machining center system

Basic functions, etc.

M800/M80/E80/C80 Series

Programming Manual

(Machining Center System) (2/2)

IB-1501278 G code programming for machining center system

Functions for multi-part system, high-accuracy function, etc.

M800/M80/E80/C80 Series

Alarm/Parameter Manual IB-1501279 Alarms

Parameters

Manuals for MTBs (NC)

Manuals for MTBs (drive section)

Manual IB No. Purpose and Contents

M800/M80/E80/C80 Series

Specifications Manual (Function) IB-1501505 Model selection

Outline of various functions

M800/M80/E80/C80 Series

Specifications Manual (Hardware) IB-1501506 Model selection

Specifications of hardware unit

M800W/M80W Series

Connection and Setup Manual IB-1501268 Detailed specifications of hardware unit

Installation, connection, wiring, setup (startup/adjustment)

M800S/M80/E80 Series

Connection and Setup Manual IB-1501269 Detailed specifications of hardware unit

Installation, connection, wiring, setup (startup/adjustment)

C80 Series

Connection and Setup Manual IB-1501452 Detailed specifications of hardware unit

Installation, connection, wiring, setup (startup/adjustment)

M800/M80/E80 Series

PLC Development Manual IB-1501270

Electrical design

I/O relation (assignment, setting, connection), field network

Development environment (PLC on-board, peripheral

development environment), etc.

M800/M80/E80 Series

PLC Programming Manual IB-1501271

Electrical design

Sequence programming

PLC support functions, etc.

M800/M80/E80/C80 Series

PLC Interface Manual IB-1501272 Electrical design

Interface signals between NC and PLC

M800/M80/E80 Series

Maintenance Manual IB-1501273 Cleaning and replacement for each unit

Other items related to maintenance

C80 Series

Maintenance Manual IB-1501454 Cleaning and replacement for each unit

Other items related to maintenance

Manual IB No. Contents

MDS-E/EH Series

Specifications Manual IB-1501226 Specifications for power supply regeneration type

MDS-E/EH Series

Instruction Manual IB-1501229 Instruction for power supply regeneration type

MDS-EJ/EJH Series

Specifications Manual IB-1501232 Specifications for regenerative resistor type

MDS-EJ/EJH Series

Instruction Manual IB-1501235 Instruction for regenerative resistor type

MDS-EM/EMH Series

Specifications Manual IB-1501238 Specifications for multi-hybrid, power supply regeneration

type

MDS-EM/EMH Series

Instruction Manual IB-1501241 Instruction for multi-hybrid, power supply regeneration type

DATA BOOK IB-1501252 Specifications of servo drive unit, spindle drive unit, motor, etc.

Manuals for MTBs (Others)

■For M800/M80/E80 Series

■For C80 Series

Manual No. Purpose and Contents

GOT2000 Series User’s Manual

(Hardware) SH-081194 Outline of hardware such as part names, external dimensions,

installation, wiring, maintenance, etc. of GOTs

GOT2000 Series User’s Manual

(Utility) SH-081195 Outline of utilities such as screen display setting, operation

method, etc. of GOTs

GOT2000 Series User’s Manual

(Monitor) SH-081196 Outline of each monitor function of GOTs

GOT2000 Series Connection

Manual (Mitsubishi Electric

Products)

SH-081197 Outline of connection types and connection method between

GOT and Mitsubishi Electric connection devices

GT Designer3 (GOT2000) Screen

Design Manual SH-081220 Outline of screen design method using screen creation

software GT Designer3

Manual No. Purpose and Contents

GOT2000/GOT1000 Series CC-Link

Communication Unit User's Manual IB-0800351 Explanation for handling CC-Link communication unit (for

GOT2000 series/GOT1000 series)

GX Developer Version 8 Operating

Manual (Startup) SH-080372E Explanation for system configuration, installation, etc. of PLC

development tool GX Developer

GX Developer Version 8 Operating

Manual SH-080373E Explanation for operations using PLC development tool GX

Developer

GX Converter Version 1 Operating

Manual IB-0800004E Explanation for operations using data conversion tool GX

Converter

MELSEC-Q CC-Link System Master/

Local Module User’s Manual SH-080394E Explanation for system configuration, installation, wiring, etc.

of master/local modules for CC-Link system

GOT2000 Series Connection

Manual (Non-Mitsubishi Electric

Products 1)

SH-081198ENG

Explanation for connection types and connection method

between GOT and other company's devices

GOT2000 Series Connection

Manual (Non-Mitsubishi Electric

Products 2)

SH-081199ENG

GOT2000 Series Connection

Manual (Microcomputers, MODBUS/

Fieldbus Products, Peripherals)

SH-081200ENG

Explanation for connection types and connection method

between GOT and microcomputers, MODBUS/fieldbus

products, peripherals

GT SoftGOT2000 Version1

Operating Manual SH-081201ENG

Explanation for system configuration, screen configuration

and operation method of monitoring software GT

SoftGOT2000

Manual No. Purpose and Contents

MELSEC iQ-R Module Configuration

Manual SH-081262 Outline of system configuration, specifications, installation,

wiring, maintenance, etc.

MELSEC iQ-R CPU Module User’s

Manual (Startup) SH-081263 Outline of specifications, procedures before operation,

troubleshooting, etc. for CPU module

MELSEC iQ-R CPU Module User’s

Manual (Application) SH-081264 Outline of memory, functions, devices, parameters, etc. for

CPU module

QCPU User’s Manual (Hardware

Design, Maintenance and

Inspection)

SH-080483

Outline of specifications, necessary knowledge to configure

the system and maintenance-related descriptions for Q series

CPU module, etc.

GX Works3 Operating Manual SH-081215 Outline of functions, programming, etc.

Reference Manual for MTBs

Manual No. Purpose and Contents

M800/M80 Series Smart safety

observation Specification manual BNP-C3072-022

Explanation for smart safety observation function

C80 Series Smart safety observation

Specification manual BNP-C3077-022

M800/M80 Series CC-Link (Master/

Local) Specification manual BNP-C3072-089 Explanation for CC-Link

M800/M80 Series PROFIBUS-DP

Specification manual BNP-C3072-118 Explanation for PROFIBUS-DP communication function

M800/M80 Series Interactive cycle

insertion (Customization)

Specification manual

BNP-C3072-121-

0003 Explanation for interactive cycle insertion

M800/M80 Series EtherNet/IP

Specifications manual BNP-C3072-263 Explanation for EtherNet/IP

Precautions for Safety

Always read this manual and enclosed documents before installation, operation, maintenance and inspection to

ensure correct usage. Thoroughly understand the basics, safety information and precautions of the devices before

using.

This manual classifies the safety precautions into "DANGER", "WARNING" and "CAUTION".

Note that the items under " CAUTION" could lead to serious consequences as well depending on the situation.

All the items are important and must always be observed.

The following sings indicate prohibition and compulsory.

The meaning of each pictorial sing is as follows.

DANGER

When the user could be subject to imminent fatalities or serious injuries if handling is mistaken.

WARNING

When the user could be subject to fatalities or serious injuries if handling is mistaken.

CAUTION

When the user could be subject to injuries or the property could be damaged if handling is mistaken.

This sign indicates prohibited behavior (must not do).

For example, indicates "Keep fire away".

This sign indicated a thing that is pompously (must do).

For example, indicates "it must be grounded".

CAUTION

CAUTION rotated

object

CAUTION HOT

Danger Electric shock

risk

Danger explosive

Prohibited

Disassembly is

prohibited

KEEP FIRE AWAY

General instruction

Earth ground

Mitsubishi CNC is designed and manufactured solely for applications to machine tools to be used for industrial

purposes.

Do not use this product in any applications other than those specified above, especially those which are

substantially influential on the public interest or which are expected to have significant influence on human lives or

properties.

1. Items related to prevention of electric shocks

For Safe Use

WARNING

Do not open or remove the front cover while the power is ON or during operation. The high voltage

terminals and charged sections will be exposed, and this could result in electric shocks.

Do not remove the front cover even when the power is OFF, except for the wiring works or periodic

inspections. The inside of the controller and drive unit are charged, and this could result in electric shocks.

Always wait at least 15 minutes after turning the power OFF. Then, check the voltage with a tester, etc.,

before wiring works, inspections or connecting with peripheral devices. Failure to observe this could result

in electric shocks.

Earth ground the controller, drive unit and motor according to the local laws. (In Japan, ground the 200V

Series input products with Class C or higher protective grounding and the 400V Series input with Class D

or higher protective grounding.)

All wiring works, maintenance and inspections must be carried out by a qualified technician. Failure to

observe this could result in electric shocks. Contact your nearby Service Center or Service Station for

replacing parts and servicing.

Wire the controller, drive unit and motor after installation. Failure to observe this could result in electric

shocks.

Do not operate the switches with wet hands. Failure to observe this could result in electric shocks.

Do not damage, apply excessive stress, place heavy things on or sandwich the cables. Failure to observe

this could result in electric shocks.

Insulate the power lead using a fixed terminal block. Failure to observe this could result in electric shocks.

Completely turn off the all lines of the power supply externally before wiring. Not completely turning off all

power could result in electric shock or damage to the product.

When turning on the power supply or operating the module after wiring, be sure that the module's terminal

covers are correctly attached.

Not attaching the terminal cover could result in electric shock.

2. Items related to prevention of fire

3. Items related to prevention of bodily injury or property damage

CAUTION

Install the controller, drive unit, motor and regenerative resistor on non-combustible material. Installation

directly on or near combustible materials could result in fires.

If any malfunction in the unit is observed, shut off the power at the unit’s power supply side. Continuous

flow of large current could result in fires.

Install an appropriate no fuse breaker (NFB) and contactor (MC) on the power input section of the drive unit

and configure the sequence that shuts the power off upon drive unit’s emergency stop or alarm.

When a breaker is shared for multiple power supply units, the breaker may not function upon short-circuit

failure in a small capacity unit. Do not share a breaker for multiple units as this is dangerous.

Incorrect wiring and connections could cause the devices to damage or burn.

DANGER

When transporting or installing a built-in IPM spindle or linear servomotor, be careful so that your hand or

property will not be trapped in the motors or other metal objects. Also keep the devices with low magnetic

tolerance away from the product.

CAUTION

Do not apply voltages to the connectors or terminals other than voltages indicated in the connection and

setup manual for the controller or specifications manual for the drive unit. Failure to observe this could

cause bursting, damage, etc.

Incorrect connections could cause the devices to rupture or damage, etc. Always connect the cables to the

indicated connectors or terminals.

Incorrect polarity (+ -) could cause the devices to rupture or damage, etc.

Persons wearing medical devices, such as pacemakers, must stay away from this unit. The

electromagnetic waves could adversely affect the medical devices.

Fins on the rear of the unit, regenerative resistor and motor, etc., will be hot during operation and for a while

after the power has been turned OFF. Do not touch or place the parts and cables, etc. close to these

sections. Failure to observe this could result in burns.

Do not enter the machine’s movable range during automatic operation. Keep your hands, feet or face away

from the spindle during rotation.

Autres manuels pour C80 Series

Table des matières

Autres manuels Mitsubishi Electric Système de contrôle

Mitsubishi Electric

Mitsubishi Electric LMAP02-E Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Trane TE-50A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Manuel du propriétaire

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric M800VW Series Manuel du propriétaire

Mitsubishi Electric

Mitsubishi Electric PAC-WHS01WF-E Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MEHITS MANAGER 3000+ Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AL2-EEPROM-2 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric M80 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric CB10 ME Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric TC-24A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric M70V Series Manuel d'instructions

Mitsubishi Electric

Mitsubishi Electric C70 Guide de l'utilisateur

Mitsubishi Electric

Mitsubishi Electric CNC 700 Series Manuel d'instructions

Mitsubishi Electric

Mitsubishi Electric PAR-CT01MAA-SB Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric BAC-HD150 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELDAS 600 Series Manuel d'instructions

Mitsubishi Electric

Mitsubishi Electric Evolution+ s-MEXT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric TW-50A Guide rapide

Mitsubishi Electric

Mitsubishi Electric C80 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65VBTCU-68DAVN Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MDS-E Series Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur