Minuteman CPE 1000 Manuel utilisateur

CPE On-Line Series Quick Install Procedure

Please read all of the WARNINGS, CAUTIONS and the User’s Manual before attempting to

install or service the UPS.

WARNING: This UPS contains potentially hazardous voltages. Risk of Electrical shock. The internal batteries

energize hazardous live parts inside this UPS even when the AC input power is disconnected.

NOTE: Installing or Servicing of the UPS must be performed by Qualified Service Personnel ONLY. MINUTEMAN

accepts no liabilities and is not limited to: injury to the Service Personnel, or damages to; the UPS, or the connected

equipment caused by the incorrect installation or servicing of the UPS.

NOTE: These UPSs are shipped with the batteries disconnected. The batteries must be connected before putting these

UPSs into service.

CAUTION: Although battery system voltages are 36VDC, 72VDC and 96VDC the battery system can still present a risk

of electrical shock. These batteries produce sufficient current to burn wire or tools very rapidly, producing molten metal.

Observe these precautions when installing or servicing the batteries:

1. Remove watches, rings, or other metal objects.

2. Use hand tools with insulated handles.

3. Wear protective eye gear (goggles), rubber gloves and boots.

4. Do not lay tools or other metal parts on top of batteries.

5. Disconnect the charging source prior to connecting or disconnecting the battery terminals.

6. Determine if the battery is inadvertently grounded. If the battery is, remove the source of the grounding. Contact

with any part of a grounded battery can result in an electrical shock. The likelihood of such shock will be reduced, if

such grounds are removed during installation and maintenance.

INSTALLATION

Be sure to read the installation placement and all the cautions before installing the UPS. Place the UPS in the final

desired location and complete the rest of the installation procedure. These UPSs are shipped with the internal batteries

disconnected. The batteries must be connected before putting these UPSs into service. Follow the procedure below to

connect the batteries. USE CAUTION: The UPS is heavy. Use the appropriate number of personnel when installing the

UPS.

AC F U S E

1. Remove the UPS from the shipping box and set on the floor or a bench top.

2. Remove the cover screws.

3. Remove the cover.

4. Verify that the voltage and frequency ratings match that of the Utility power, and then connect the AC Input power

cord into a two-pole, three-wire grounded receptacle only. Do not use extension cords, adapter plugs, or surge strips.

5. Wait for approximately 10-seconds until the Green Utility LED (#6) on the front panel turns on.

6. Connect the Battery Negative (Black) wire to the Battery Negative terminal.

7. Disconnect the UPS’s AC Input power cord from the wall outlet.

8. Re-install the cover.

9. Re-install the cover screws.

10. Plug the equipment into the output receptacles on the rear panel of the UPS. Do not use extension cords, adapter

plugs or surge strips on the output of the UPS. Ensure that the load does not exceed the maximum output rating of

the UPS (refer to the information label on the UPS or the Electrical Specifications in the User’s Manual).

11. Plug the UPS’s AC Input power cord into the wall outlet.

12. Press the Main switch on the front panel to turn on the UPS. The fan on the rear panel will start.

13. After 7~10 seconds, the start-up of UPS will be completed, then the "Utility" LED and Inverter" LED will illuminate

simultaneously.

14. Turn on the connected equipment.

15. Press and hold the Test/Alarm Silencer Button for 10-seconds to perform a Self-Test to verify proper operation of the

UPS.

16. The installation is complete the UPS is ready for normal operation. See the UPS User’s Manual for more detailed

information.

CPE 1000, CPE 1000i, CPE 1000PP CPE 2000, CPE 2000i, CPE 2000j

2KVA

3KVA 1KVA

CPE 3000, CPE 3000i

34000268 R6

1. Main Switch This is to turn the UPS on/off.

2. Self-Test OK LED Green LED illuminates if the self-test is O.K.

3. Test/Silence a. Alarm Silence.

b.1.For Standard Unit: Self-Test. Press the

button over 10 sec.

b.2.For Unit with Manual Bypass

function(Special order required): Press the

button over 5 seconds, the UPS will be

switched to Bypass mode and vice versa.

c. Displays the percentage of output load

level in AC Mode, and the battery capacity in

the Battery Mode.

4. Fault LED Red LED illuminates if the UPS detects an

Internal Fault.

5. Bypass LED Amber LED illuminates when UPS is in

Bypass mode.

6. Utility LED a. AC normal: Green LED illuminates.

b. 100% for load levels & battery capacity.

7. Inverter LED a. Inverter On: Green LED illuminates.

b. 75% for load levels & battery capacity.

8. Low Battery

Warning LED

a. Battery Low: Red LED illuminates.

b. 50% for load levels & battery capacity.

9. Overload LED a. Overload condition: Red LED illuminates.

b. 25% for load levels & battery capacity.

Ce manuel convient aux modèles suivants

Autres manuels Minuteman UPS

Minuteman

Minuteman PRO-E Manuel utilisateur

Minuteman

Minuteman MN 325 Manuel utilisateur

Minuteman

Minuteman MCP-E Manuel utilisateur

Minuteman

Minuteman MN 325/MN 525 Manuel utilisateur

Minuteman

Minuteman 6-10KVA Tower Manuel utilisateur

Minuteman

Minuteman CPE 1000 On-Line Series Instructions d'utilisation

Minuteman

Minuteman PRO1100E Manuel utilisateur

Minuteman

Minuteman Smart Up Series Manuel utilisateur

Minuteman

Minuteman E1000RM1U Manuel utilisateur

Minuteman

Minuteman EN750 Manuel utilisateur

Minuteman

Minuteman MBK-E SERIES Manuel utilisateur

Minuteman

Minuteman Endeavor RTXL Series Manuel utilisateur

Minuteman

Minuteman Endeavor ED6000T Manuel utilisateur

Minuteman

Minuteman Encompass Series Manuel utilisateur

Minuteman

Minuteman XRT Series Manuel utilisateur

Minuteman

Minuteman AT300 Manuel utilisateur

Minuteman

Minuteman Endeavor ED1000RTXL2U Manuel utilisateur

Minuteman

Minuteman Entrepid Series Manuel utilisateur

Minuteman

Minuteman ED6200RM Manuel utilisateur

Minuteman

Minuteman PARASHIELD 1224 Manuel utilisateur

Minuteman

Minuteman ERS1500RTNC Manuel utilisateur

Minuteman

Minuteman Encompass EC1000RT2U Manuel utilisateur

Minuteman

Minuteman Enterprise Plus LCD RTXL UPS Series Manuel utilisateur

Minuteman

Minuteman E750RM2U Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur