Minebea CSA-507C Manuel utilisateur
Transmitter
CSA-507C
Instruction Manual
EN294-1459-B
I
FOREWORD
Thank you very much for your purchasing our Transmitter CSA−507C.
This manual explains installation procedures and connecting method and also operating
method for Transmitter CSA−507C. Make use of it properly after reading through the
manual carefully.
Be sure to deliver the manual to the end user. Moreover, the end user should keep the
manual at hand after reading it over.
II
Marks and arrangements used in this manual
The following symbols are attached to the explanation on the matters that alert
“Do not do this.”, “Take care.” and “For reference”.
Be sure to read these items where these marks are attached.
Warning ●Precaution which must be followed to prevent the possibility of
accident or serious injury to the operators.
To avoid possible hazard, do not perform any procedure described
here.
●Precautions and important informations for safe operation and
service personnels.
Be sure to read the item to prevent from malfunction.
Mark during operation
●Press the switch.
III
For safe operation
Be sure to read this manual before use.
1. Installation place
●Use the instrument where the temperature/humidity specifies within
the range as follows:
Environmental temperature : −10 ℃〜50 ℃
Environmental humidity : Less than 85 %RH(Non condensing.)
(1) Location where installation is not allowed.
Warning ●Do not locate the instrument on the places such as follows:
It may cause an unexpected faulty in the instrument.
DDo not expose the instrument in direct sunlight and/or high temperature
area.
DDo not use the instrument in a high humid area.
DDo not install the instrument where there is high mechanical vibration or
shock.
DDo not use the instrument where there are excess of dusts and fine
particles.
DDo not install the instrument where there includes any corrosive gas or
any salty atmosphere.
DDo not install the instrument where there is rapid change on temperature
and humidity.
DDo not install the instrument near the devices that are magnetized or
generate an electromagnetic field.
DDo not install the instrument where there may suffer radioactivity or
radioactive rays.
DAvoid the location where chemical reaction may take place such as in a
laboratory.
IV
(2) Installation
●When installing the instrument, install as referring to the following
dimensions and secure the space around the instrument.
Each dimensions of the instrument and required dimensions for the environmental
spaces are as follows:
Dimensions for installation
Dimensions when the optional Auto zero unit(CSA507C−P99) is installed.
44 110
2−φ4.5
110
102
90
45
2−M4
Panel cut size
95
102
(9)
44 230
2−φ4.5
110
102
90
Unit：mm
(9)
V
2. Power supply
Warning ●Be sure to check that power supply is off when installing each cable.
If the work is done with the power fed, there may have the possibility
of electric shock to the operator or even the possibility of destroying
the instrument.
●Before supplying the power, check that the indication of power supply
voltage/specifications for the instrument and the power going to
supply should be the same. If they are not equal, contact us.
If you use the instrument without checking them, it may cause a
damage in the instrument or electric shock to the operator.
●Grounding wire should be connected securely. When grounding wire
is not connected, it may cause a malfunction of the instrument or
electric shock to the operator.
3. Application note
Warning ●Before using a new instrument or exchanging the strain gage applied
transducer for a new one, be sure to make calibration.
If calibration shall not be made, correct measured results may not be
obtained nor it may cause a malfunction in the instrument and there
may exist damage in peripheral equipments.
Besides, even though calibration had been made, there may occur the
similar case when the result is not correct, so make calibration again.
Warning ●In case of using the instrument, check that the connections are
executed properly. If not connected properly, correct measured result
will not be obtained, nor it may cause malfunctions of the instrument,
damage to the peripheral equipments or even worse serious accidents.
Warning ●When change of setting is made carelessly on the instrument during
measurement, it may cause malfunction in the instrument and also
possibility of damage in peripheral equipments.
VI
Warning ●Do not shock the instrument such as throwing something on it.
It may cause the damage to the case and also may cause the damage
to the instrument in resisting to environment.
VII
History of revision
Date
Instruction manual No.
Details of revised point
Sep. 2010
DRW. NO.EN294-1459
First Version
May. 2012
DRW. NO.EN294-1459-A
Duo.FN12−02078
Feb. 2018
DRW.No.EN294-1459-B
Due to ECN FN17-02017
・Delete the company name in the cover page.
・Delete the company name in the contents.
Table des matières
Autres manuels Minebea Émetteur
Minebea
Minebea CSA-522B Manuel utilisateur
Minebea
Minebea CSA-528-80-4 Manuel utilisateur
Minebea
Minebea CSA-593 Manuel utilisateur
Minebea
Minebea CSA-524 Manuel utilisateur
Minebea
Minebea OPT-563B-71 Manuel utilisateur
Minebea
Minebea OPT-564 Manuel utilisateur
Minebea
Minebea CSA-521 Manuel utilisateur
Minebea
Minebea CSA-562B Manuel utilisateur
Minebea
Minebea CSA-591 Manuel utilisateur
Minebea
Minebea OPT-563B Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
