Minarik LV Series Manuel utilisateur
USER’S MANUAL
LV Series
Low Voltage Input, Pulse-Width Modulated,
Adjustable Speed Drives
for DC Brush Motors
Models: LV01-24AC-E10U
LV02-24AC
LV02-24DC
All rights reserved. No part of this manual may be reproduced or transmitted in any
form without written permission from Minarik Drives. The information and technical
data in this manual are subject to change without notice. Minarik Drives makes no
warranty of any kind with respect tothis material, including, but not limited to, the
implied warranties of its merchantability and fitness for a given purpose. Minarik
Drives assumes no responsibility for any errors that may appear in this manual and
makes no commitment to update or tokeep current the information in this manual.
Copyright © 2013 by
Minarik Drives
Printed in the United States of America.
i
Safety Warnings
Throughout this manual, this symbol denotes an
important safety tip. Read these sections very carefully!
• Have a qualified electrical maintenance technician install,
adjust and service this equipment. Follow the National
Electrical Code and all other applicable electrical and safety
codes, including the provisions of the Occupational Safety
and Health Act (OSHA), when installing equipment.
•Reduce the chance of an electrical fire, shock, or explosion by
proper grounding, over-current protection, thermal protection,
and enclosure. Follow sound maintenance procedures.
•It is possible for a drive to run at full speed as a result of a
component failure. To stop the drive in an emergency, ensure
that a master switch has been installed in the AC line.
•This drive is not isolated from earth ground. Circuit
potentials of up to 115 VAC exist on the board.Direct contact
with the printed circuit board or with circuit elements poses the
risk of serious injury or fatality. Use a non-metallic screwdriver
for adjusting the calibration trimpots
ii
Contents
isgninraWytefaS
1snoitacificepS
2snoisnemiD
4noitallatsnI
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
5gniriW
Line Fusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Shielding guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Speed adjust potentiometer installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connections (LV series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connections (LV-E10U series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Voltage follower (LV series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Voltage follower (LV-E10U series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
31noitarepO
31rewopgniylppaerofeB
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Line starting and stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Decelerating to a stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Dynamic braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
61noitarbilaC
MINIMUM SPEED (MIN SPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
MAXIMUM SPEED (MAX SPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
TORQUE LIMIT (TQ LIMIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
IR COMPENSATION (IR COMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
iii
12setoNnoitacilppA
Multiple fixed speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Adjustable speeds using potentiometers in series . . . . . . . . . . . . . . . . . . . .22
Independent adjustable speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
RUN/JOG switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Reversing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
62gnitoohselbuorT
Before troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
revockcabedisniytnarraWdetimiL
iv
Illustrations
Figure 1. LV Series Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Figure 2. LV-E10U Series Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Figure 3. Speed Adjust Potentiometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 4. LV Series Line Input and Speed Potentiometer Connections . . . . . . . . .8
Figure 5. LV Series Motor Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Figure 6. LV-E10U Series Drive Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Figure 7. LV Series Voltage Follower Connections . . . . . . . . . . . . . . . . . . . . . . . .11
Figure 8. LV-E10U Voltage Follower Connections . . . . . . . . . . . . . . . . . . . . . . . .12
Figure 9. Run/Decelerate to Zero Speed Switch . . . . . . . . . . . . . . . . . . . . . . . . . .14
Figure 10. Dynamic Brake Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 11. LV SERIES Calibration Trimpot Layout . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 12. LV-E10U SERIES Calibration Trimpot Layout . . . . . . . . . . . . . . . . . . .17
Figure 13. Multiple Fixed Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Figure 14. Adjustable Fixed Speeds Using Potentiometers in Series . . . . . . . . . .22
Figure 15. Independent Adjustable Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Figure 16. RUN/JOG Switch Connection to Speed Adjust Potentiometer . . . . . .24
Figure 17. Reversing Circuit Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Specifications
Maximum
Armature Armature
Input Current Voltage HP
Model Voltage (Amps DC) Range** Range
LV01–24AC-E10U 8–24 VAC* 1.0 0–22 VDC 1/500–1/100
LV02–24AC 8–24 VAC* 2.0 0–22 VDC 1/250–1/50
LV02–24DC 10–36 VDC 2.0 0–22 VDC 1/250–1/50
**AC input voltage is ±10%, 50/60 Hz, single phase
** Maximum output voltage is 91% of input voltage. Rating shown is with 24V input.
Form Factor 1.05 at base speed
Acceleration Time 1 second
Deceleration Time 1 second
Load Regulation (at base speed) 2%
Ambient Temp. Range 10°C–40°C
Vibration 0.5g max (0 – 50 Hz)
0.1g max (above 50 Hz)
1
Analog Input Voltage Range (S1 to S2) 0-4.6 VDC
2
Dimensions
VFB INGN D
OUT
COMP
D 5 0 4
D 5 0 3
R 5 0 1
IC 5 0 1
C 5 0 1
D 5 0 1
D 5 0 2
M IN S P DM A X S P D
A C 1 A C 2 A 2 S 3 S2 S 1A 1
D 5 0 5
C 5 0 2
0.150" [4]
2.100" [53]
2.250" [57]
0.150" [4]
2.100" [53]
2.250" [57]
Figure 1. LV01 Series Dimensions
ALL DIMENSIONS IN INCHES [MILLIMETERS]
2.250 [57]
2.100 [53]
0.150 [4]
2.100 [53]
2.250 [57]
0.150 [4]
3
Dimensions
A 1
IC 5 0 1
D 5 0 1
A 2
R 5 0 1
IR C O M P
TQ LIM I T
C 5 0 1
B R 5 0 1
L2
R 5 0 2
L1
S 1
S 2
S 3
C 5 0 3
M A X S P D
M IN S P D
C 5 0 2
D C + I N
D C - I N
C501 ( ALTERNA TE)
+ ~ ~ -
0.97 [25]
1.28 [33]
1.40 [36]
0.74 [19]
1.75 [44]
3.58 [91]
3.80 [97]
4.30 [109]
0.64 [16]
0.19 [5]
0.19 [5]
Figure 2. LV02 Series Dimensions
ALL DIMENSIONS IN INCHES [MILLIMETERS]
3.58 [91]
1.75 [44]
0.74 [19]
3.80 [97]
4.30 [109]
0.19 [5]
0.97 [25]
1.28 [33]
1.40 [36]
0.19 [5]
0.64 [16]
4
*Does not apply to LV01-24AC/DC-E10U
Mounting
• Drive components are sensitive to electrostatic fields. Avoid
direct contact with the circuit board. Hold drive by the chassis
only.
• Protect the drive from dirt, moisture, and accidental contact.
Provide sufficient room for access to the terminal block and
calibration trimpots.
• Mount the drive away from heat sources. Operate the drive
within the specified ambient operating temperature range.
• Prevent loose connections by avoiding excessive vibration of
the drive.
• Mount drive with its board in either a horizontal or vertical
plane. Six 0.19 in. (5 mm) wide slots in the chassis accept #8
pan head screws. Fasten either the large base or the narrow
flange of the chassis to the subplate.*
• The chassis must be earth grounded. Use a star washer beneath
the head of at least one of the mounting screws to penetrate the
anodized chassis surface and to reach bare metal.
Do not install, rewire, or remove this control with input
power applied. Doing so may cause fire or serious injury.
Make sure you have read and understood the Safety
Warnings on pg i before attempting installation.
Installation
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Minarik Entraînement CC
Minarik
Minarik HTL05-D-4Q Manuel utilisateur
Minarik
Minarik MMBOSS Series Manuel utilisateur
Minarik
Minarik DC30-12-4Q-L Manuel utilisateur
Minarik
Minarik RG5500U Manuel utilisateur
Minarik
Minarik RG501A Manuel utilisateur
Minarik
Minarik VFDP4X04-D230-PCM Manuel utilisateur
Minarik
Minarik MM21036A Manuel utilisateur
Minarik
Minarik PCM23000A Series Manuel utilisateur
Minarik
Minarik XL1100A Manuel utilisateur
Minarik
Minarik NRGD-4Q Series Manuel utilisateur
Minarik
Minarik C1XP02-115AC Manuel
Minarik
Minarik MM300 Series Manuel utilisateur
Minarik
Minarik PCM21000A Manuel utilisateur
Minarik
Minarik MMRG Series Manuel utilisateur
Minarik
Minarik RG500 Series Manuel utilisateur
Minarik
Minarik MM-PCM Series Manuel utilisateur
Minarik
Minarik MM20000A Series Manuel utilisateur
Minarik
Minarik XP-AC-SL Series Manuel utilisateur
Minarik
Minarik M2 Manuel utilisateur
Minarik
Minarik XP-AC Series Manuel utilisateur
Manuels Entraînement CC populaires d'autres marques
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces
Chamberlain Garog
Chamberlain Garog D Series Manuel utilisateur
Parker
Parker PDS Series Manuel utilisateur
Festo
Festo DGC G Series Guide de configuration
Binks
Binks QS-5012-1-CE Manuel utilisateur
