MIMAKI CG-60SL Instructions de montage

Supplement for the Basic Operation manual

MIMAKI ENGINEERING CO., LTD. D202064-10

The following functions are added from firmware version 1.80.

Please read this manual and fully understand it before using the device.

If you have any question, contact your local distributor.

This manual correspond to the models as firmware version 1.80 or later.

When turning on the power, you can confirm the firmware version.

Table of Contents

Make the media without uncut area ................................................................................ 2

Other Convenient Settings ............................................................................................... 3

Error message ................................................................................................................... 4

2

Make the media without uncut area

By over wrapping the start point and the end point arbitrarily, you can

make the media without uncut area.

Specify the over cut function (valid/invalid) and the length of the over cut.

If the length of the over cut is set, when cut starts, cut will be performed

from the position to the front by the specified length and the tool will move

up going too far at the end.

1Press the key in the local mode.

2Press the jog key or to select [SET UP] .

3Press the key.

4Press the jog key or to select [OVER

CUT] .

5Press the key.

6Press the jog key or to select OVER

CUT setting.

•Set values : OFF or a value from 0.1 to 1.0mm (0.1mm unit)

7Press the key.

8Press the key twice for terminating this function.

• Setting proper over cut can reduce uncut area of start and end point of a media easy to bend. If too

large value is set, the result may have a rupture

Over cut

part

DATA CLEAR <ENT >

FUNCTION

SET UP <ENT>

ENTER/HOLD

OVER CUT < e n t >

OVER CUT : OF F

ENTER/HOLD

OVER CUT : 0 . 3mm

0.1 ~ 1mm

0.1 ~ 1mm

ENTER/HOLD

END

3

Other Convenient Settings

The setting items are added in the "Other Convenient Settings" of the Operation Manual page.3-59.

The following three items are added.

Function name Outline Setting values

Over Cut Make the media without uncut area. OFF/ 0.1 to 1.0 mm

Start Mode Set the mode after detecting the sheet.

LCL

The mode switches to the

standby condition of the local

mode after detecting the sheet.

REM

The mode automatically

switches to the remote mode

after detecting the sheet.

4

Error message

The error message is added.

If the following message appears, take an appropriate remedy according to the table below.

If the remedy does not work, contact your distributor or an sales office of MIMAKI.

Error message Cause Remedy

ERR51 PINCH POS* The pinch rollers are not on the grit roll-

ers.

Move the pinch rollers onto the grit roll-

ers.

5

6

Memo

7

D202064-10-27052009

All Rights Reserved. NH

© MIMAKI ENGINEERING CO., LTD. FW:1.80

Autres manuels pour CG-60SL

2

Autres manuels MIMAKI Traceur

MIMAKI

MIMAKI JV33 Series Mode d'emploi

MIMAKI

MIMAKI CG-75FXII Manuel utilisateur

MIMAKI

MIMAKI DS-1600 Manuel utilisateur

MIMAKI

MIMAKI CF-0912 Manuel utilisateur

MIMAKI

MIMAKI CF2 Series Manuel utilisateur

MIMAKI

MIMAKI TS500 Manuel utilisateur

MIMAKI

MIMAKI CF22-1225 Manuel utilisateur

MIMAKI

MIMAKI CG-60st Manuel utilisateur

MIMAKI

MIMAKI CG-60SR Manuel utilisateur

MIMAKI

MIMAKI JV3-75SPII Manuel utilisateur

MIMAKI

MIMAKI CG-AR Series Manuel technique

MIMAKI

MIMAKI JV400-LX Manuel utilisateur

MIMAKI

MIMAKI TS34-1800A Guide de référence

MIMAKI

MIMAKI JV4 Series Manuel utilisateur

MIMAKI

MIMAKI JV33 Series Instructions de montage

MIMAKI

MIMAKI CJV150 series Manuel utilisateur

MIMAKI

MIMAKI UJF-605C Instructions de montage

MIMAKI

MIMAKI JV3-160SP Manuel utilisateur

MIMAKI

MIMAKI DM3-1810S Manuel utilisateur

MIMAKI

MIMAKI TextileJet Tx2-1600 Series Manuel utilisateur

MIMAKI

MIMAKI JV400-SUV Series Manuel d'entretien

MIMAKI

MIMAKI JFX200-2513EX Manuel d'entretien

MIMAKI

MIMAKI UCJV300 Guide de démarrage rapide

MIMAKI

MIMAKI TPC-1000 Instructions d'installation

Manuels Traceur populaires d'autres marques

MUTOH

MUTOH Kona 760 Manuel utilisateur

HP

HP 7475a Manuel utilisateur

Vulcan-Hart

Vulcan-Hart FC-500VC Manuel utilisateur

Roland

Roland TrueVIS VG-640 Manuel du propriétaire

Furuno

Furuno RP-180 Manuel utilisateur

Roland

Roland VersaCamm SP-540V Manuel utilisateur

Ioline

Ioline Summit Manuel utilisateur

Summa

Summa S CLASS Manuel utilisateur

Gerber Technology

Gerber Technology GERBERplotter MP Series Manuel utilisateur

Furuno

Furuno RP-17 Manuel utilisateur

HP

HP 7470A Manuel utilisateur

SII

SII LP-1010 Manuel utilisateur

Great Computer

Great Computer JII-61 Manuel utilisateur

Roland

Roland VersaUv LEF - 12i Manuel utilisateur

Lectra

Lectra Alys 120 Manuel utilisateur

MUTOH

MUTOH Ultima SC-850D Manuel utilisateur

Skycut

Skycut D Series Manuel utilisateur

Commodore

Commodore 1520 Manuel utilisateur