Milwaukee SM100 Manuel utilisateur

Milwaukee

USER MANUAL

PORTABLE

pH METER

MODEL: SM100

Smart pH Meter

ISMIL100 11/01

SPECIFICATIONS:

SM100

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

pH ELECTRODE MA911B/1 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 1 x 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 145 x 80 x 40 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution, 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution, 20 ml sachet (25 pcs)

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 220 ml bottle

MA911B/1 pH-electrode with BNC connector and 1 m cable

MA950 Portable meter wall fixing kit

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing for

a period of two years from the date of purchase.

The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please return

the parts to either dealer or our office and the repair will be effected free of

charge.

Note: We reserve the right to modify the design, construction and appearance

of our products without advance notice.

Milwaukee

www.ponpe.comwww.ponpe.com

www.ponpe.com

contact:

[email protected]

OPERATION:

• The meter is supplied complete with

a 9V battery. Slide off the battery com-

partment cover on the back of the

meter. Install the battery while paying

attention to its polarity.

• Always remove the electrode protective

cap before taking any measurement. If

the electrode has been left dry, soak

the tip (bottom 2.5 cm) in rinse solu-

tion (M10000B) for a few minutes to

reactivate it.

• Connect the pH electrode to the BNC

socket on the top of the meter.

• Make sure that the meter has been

calibrated before taking any measure-

ments (see Calibration Procedure)

• Immerse the tip (2.5 cm) of the pH

electrode into the sample.

• Turn the instrument on by pressing the ON/OFF key.

• Allow the reading to stabilize before taking mea-

surements.

• After measurements, switch the meter off and

store the electrode with a few drops of storage

solution in the protective cap.

CALIBRATION PROCEDURE:

• Remove the protective cap from the electrode.

• Immerse the electrode tip into a new sachet of

pH7 calibration solution and allow the reading

to stabilize.

• Adjust the pH7 (OFFSET) calibration knob to

display "7.0 pH".

• Open a new sachet of pH4 cali-

bration solution and use a small

quantity to rinse the electrode.

• Immerse the electrode tip inside

the pH4 sachet and allow the read-

ing to stabilize.

• Adjust the pH4/pH10 (SLOPE) cali-

bration knob to read "4.0 pH".

• The calibration is now complete and the meter is ready to

take measurements.

• It is suggested to recalibrate the meter at least once a

month, after a prolonged stocking time and after electrode

replacement.

BATTERY REPLACEMENT:

When the battery becomes weak the

meter will display "V".

When the low battery indicator appears,

the battery has only about 50 hours of

working time left. A low battery will result

in unreliable measurements. It is recom-

mended to replace immediately the

battery.

Battery replacement must only take place

in a non-hazardous area using an alka-

line 9V battery.

Turn the meter off, slide off the battery

compartment cover at the rear of the meter

and replace the 9V battery with a new

one. Make sure the battery contacts are

tight and secure, seat the battery in its

compartment and insert the cover again.

www.ponpe.com

contact:

[email protected]

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee MI490 Manuel utilisateur

Milwaukee

Milwaukee MW10 Manuel utilisateur

Milwaukee

Milwaukee MW14 Manuel utilisateur

Milwaukee

Milwaukee PST MW100 PRO Manuel utilisateur

Milwaukee

Milwaukee M12 C4PLA Manuel utilisateur

Milwaukee

Milwaukee 2236-20 Manuel utilisateur

Milwaukee

Milwaukee MW12 Manuel utilisateur

Milwaukee

Milwaukee MA888 Manuel utilisateur

Milwaukee

Milwaukee Heavy Duty 2270-20 Manuel utilisateur

Milwaukee

Milwaukee SM801 Manuel utilisateur

Milwaukee

Milwaukee 48-22-9801 Manuel utilisateur

Milwaukee

Milwaukee MI605 Manuel utilisateur

Milwaukee

Milwaukee MI407 Manuel utilisateur

Milwaukee

Milwaukee 2235-20 Manuel utilisateur

Milwaukee

Milwaukee 48-22-5112 Manuel utilisateur

Milwaukee

Milwaukee Mi 150 Manuel utilisateur

Milwaukee

Milwaukee 2235-20 Manuel utilisateur

Milwaukee

Milwaukee pH600 Manuel utilisateur

Milwaukee

Milwaukee MW101 Manuel utilisateur

Milwaukee

Milwaukee MW11 Manuel utilisateur

Milwaukee

Milwaukee MI404 Manuel utilisateur

Milwaukee

Milwaukee PRO MI414 Manuel utilisateur

Milwaukee

Milwaukee MW170 MAX Manuel utilisateur

Milwaukee

Milwaukee MI 405 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur