Milwaukee MC125 Manuel utilisateur

SPECIFICATIONS :

pH ORP

RANGE 0.00 to 14.00 ±1000 mV

RESOLUTION 0.01 1 mV

ACCURACY (@25°C) ±0.2 ± 5 mV

SETPOINT 4 to 8 pH -200 to 600 mV

ELECTRODE (included) MA911B/2 MA921B/2

ALARM & active when measurement is

OUTPUT POWER SOCKET higher/lower than the setpoint

depending on user selection

ENVIRONMENT 0 to 50°C, 95% RH max.

POWER SUPPLY 12 VDC (included)

POWER DRIVERS 115VAC, 2A, 60Hz or 230VAC, 1A, 50Hz

DIMENSIONS 148.5 x 82.5 x 32 mm

WEIGHT 200 g meter only

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution 20 ml sachet (25 pcs)

M10000B Electrode rinse solution 20 ml sachet (25 pcs)

MA9015 Electrode storage solution 20 ml sachet (25 pcs)

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing

for a period of two years from the date of purchase.

The electrodes are warranted for a period of 6 months.

If during this period, repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please

return the parts to either dealer or our office and the repair will be effected

free of charge.

Note: We reserve the right to modify the design, construction and

appearance of our products without advance notice.

USER MANUAL

PORTABLE

pH I ORP COMBINED METER

MODEL: MC125

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

OPERATION:

•Connect the supplied 12 VDC

power adapter to the meter and

to the mains line.

•Connect the pH and ORP elec-

trode to the BNC socket of the

meter.

•Always remove the electrode

protective caps before taking any

measurement. If the electrodes

have been left dry, soak the tip

(bottom 2.5 cm) in rinse solution

(M10000B) for a few minutes to reactivate them.

•Make sure that the meter has been calibrated before taking any

measurements (see Calibration Procedure).

•Immerse the tip (2.5 cm) of the electrodes into the samples.

•Turn the instrument on by pressing the ON/OFF key.

•Allow the reading to stabilize and the meter will start continuous

monitoring.

•A blinking alarm LED will indicate when the measured pH value is

higher or lower than the setpoint depending on user selection.

•When the alarm LED is blinking, there is power in the output power

socket.

NOTE: The output power contact has no protection fuse inside the

meter. It is recommended to protected it outside, against failure.

SETPOINT:

•The setpoint can be selected by adjusting the knob to the desired

value.

•The selectable range for MC125 is from

4 to 8 for pH and from -200 to 600 mV

for ORP.

•The nature of the setpoint can be se-

lected by setting the proper switch to the

desired position (ABOVE or BELOW).

CALIBRATION PROCEDURE:

•Remove the protective cap from the pH electrode.

•Immerse the electrode tip into a new sachet of pH 7

calibration solution and allow the reading to stabilize.

•Adjust the pH7 calibration trimmer (on the front) to

display "7.00 pH".

•Open a new sachet of pH 4 calibration solution and

use a small quantity to rinse the electrode.

•Immerse the electrode tip inside the pH 4 sachet and

allow the reading to stabilize.

•Adjust the pH4/10 calibration trimmer (on the front) to

display "4.00 pH".

•The calibration is now complete and the meter is ready

to take measurements.

•It is suggested to recalibrate the meter at least

once a month, after prolonged warehousing time

and after pH electrode replacement.

INSTALLATION PROCEDURE:

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee MW500 Manuel utilisateur

Milwaukee

Milwaukee MC310 Manuel utilisateur

Milwaukee

Milwaukee MW102 Manuel utilisateur

Milwaukee

Milwaukee 2237-20 Manuel utilisateur

Milwaukee

Milwaukee MI407 Manuel utilisateur

Milwaukee

Milwaukee CD600 Manuel utilisateur

Milwaukee

Milwaukee pH 58 Manuel utilisateur

Milwaukee

Milwaukee 3712 Manuel utilisateur

Milwaukee

Milwaukee MW500 Manuel utilisateur

Milwaukee

Milwaukee MW100 Manuel utilisateur

Milwaukee

Milwaukee M12 C4PLA Manuel utilisateur

Milwaukee

Milwaukee 2212-20 Manuel utilisateur

Milwaukee

Milwaukee MI490 Manuel utilisateur

Milwaukee

Milwaukee PRO MW801 Manuel utilisateur

Milwaukee

Milwaukee SM700 Manuel utilisateur

Milwaukee

Milwaukee pH600 Manuel utilisateur

Milwaukee

Milwaukee MR32ATC Manuel utilisateur

Milwaukee

Milwaukee CALIBRATION 2238-20 Manuel utilisateur

Milwaukee

Milwaukee MW12 Manuel utilisateur

Milwaukee

Milwaukee MI 411 Manuel utilisateur

Milwaukee

Milwaukee MW306 MAX Manuel utilisateur

Milwaukee

Milwaukee MW11 Manuel utilisateur

Milwaukee

Milwaukee MI412 Manuel utilisateur

Milwaukee

Milwaukee MW101 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur