Middle Atlantic MPR-A Series Manuel utilisateur

I-00632 Rev D

MPR-A SERIES

SERIES PROTECTION MODULES

Instruction Sheet

Thank you for purchasing the MPR-A Series Protection Module. Please read these instructions

thoroughly before installing this product.

- Non-sacrificial surge technology protects equipment without compromising system ground

- No MOVs or other degrading parts

- Thermal circuit breaker overload protection

- Advanced EMI/RFI filtering

RLM-15A-SP SHOWN

Control Status

Activation

Momentary Maintained ON

OFF

AUTO

SERIES PROTECTED AND CONTROLLED

15 AMP MODULE

120V - 12A - 60Hz

RLM-15A-SP

Conforms to UL Standard

1449

Certified to CSA Standard

C22.2 No. 8

OUTPUT

Normally Closed Normally Open

RESET

U.S. Patent No. 8,947,844

Page 2

DANGER HAZARDOUS VOLTAGE/DANGER HAUTE

TENSION

The lightning flash with the arrowhead symbol, within an

equilateral triangle is intended to alert the user to the

presence of uninsulated dangerous voltage within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

L'éclair avec le symbole de flèche dans un triangle

équilatéral est destiné à alerter l'utilisateur de la présence

d'une tension dangereuse non isolée dans l'enceinte du

produit qui peut être d'une ampleur suffisante pour constituer

un risque de choc électrique pour les personnes.

CAUTION/ATTENTION

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

Le point d'exclamation dans un triangle équilatéral est

destiné à alerter l'utilisateur de la présence d'importants

instructions d’opération et de maintenance (entretien) dans la

documentation accompagnant l'appareil.

READ AND SAVE THESE INSTRUCTIONS!

CONSERVER CES INSTRUCTIONS!

• To reduce risk of shock , disconnect the device from the power source before

servicing any connected equipment

Pour réduire les risques d'électrocution, débranchez l'appareil de la source

d'alimentation avant l'entretien de tout équipement connecté

• Do not overload this device. Ensure the total load to this device does not

exceed that which is listed in the specifications section of this manual

Ne pas surcharger cette appareil. S'assurer que la charge totale à cet

appareil ne dépasse pas celle qui est répertoriée dans la section des

spécifictions de ce manuel

• To be used indoors in a dry location only

Pour être utilisé en intérieur dans un endroit sec seulement

• Do not operate with a damaged cord or plug

Ne pas faire fonctionner avec un cordon ou une prise endommagée

• Clean only with dry cloth

Nettoyer avec un chiffon sec seulement

The product meets the requirements of the following standards:

• UL Standard 1449

• CSA-C22.2 No. 8

FCC CLASS A

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. Modifications not expressly approved by the manufacturer could void the user's authority to operated the

equipment under FCC rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

REGULATORY COMPLIANCE

IMPORTANT SAFETY INSTRUCTIONS

Page 3

THE RECEPTACLES RECEIVE POWER VIA THE CONTROL CIRCUITS UNDER THE FOLLOWING CONDITIONS:

A) The AUTO-OFF-ON switch is in the ON position.

B) The AUTO-OFF-ON switch is in the AUTO position with the NORMALLY OPEN/CLOSED control selector switch in the

NORMALLY OPEN position and there is a contact closure on the remote control terminal block.

C) The AUTO-OFF-ON switch is in the AUTO position with the NORMALLY OPEN/CLOSED control selector switch in the

NORMALLY CLOSED position and there is no contact closure on the remote control terminal block.

CONTACT CLOSURE OPERATION

The customer provided contact closure connected to remote control terminal block, can be either momentary or maintained.

The MOMENTARY/MAINTAINED selector switch must be in the proper position. The terminal block control closure is

ignored when the AUTO-OFF-ON switch is in the ON or OFF position.

MOMENTARY OPERATION

A contact closure is required for the control PCB to process the control signal. Each subsequent closure will alternately turn off

and on the power to the controlled receptacles.

MAINTAINED OPERATION

With the NORMALLY OPEN/CLOSED switch in the NORMALLY OPEN position, a maintained contact closure will energize the

receptacles. When this maintained contact is removed, the receptacles will become de-energized. With the NORMALLY

OPEN/CLOSED switch in the NORMALLY CLOSED position, a maintained contact closure will de-energize the receptacles.

When this maintained contact is removed, the receptacles will become energized.

CONTROLLED OUTLET TERMINAL BLOCK

The Controlled Outlet Terminal Block provides status of outlets via a dry contact. The CLOSED position indicates the

receptacles are energized, while the OPEN position indicates that the receptacles are de-energized.

FUNCTIONALITY

Control Status

Activation

Momentary Maintained ON

OFF

AUTO

SERIES PROTECTED AND CONTROLLED

15 AMP MODULE

120V - 12A - 60Hz

RLM-15A-SP

Conforms to UL Standard

1449

Certified to CSA Standard

C22.2 No. 8

OUTPUT

Normally Closed Normally Open

RESET

Page 4

RLM-15A-SP SHOWN

CONNECTIONS, CONTROLS AND INDICATORS (RLM SERIES)

123

967

DUPLEX RECEPTACLE: All Modules contain one duplex receptacle.

15A Models - (NEMA 5-15R)

20A Models - (NEMA 5-20R)

‘MOMENTARY’ or ‘MAINTAINED’ control selection switch.

CONTROL STATUS LED: Green LED indicates receptacles are ON.

CONTROL SWITCH: ‘AUTO-OFF-ON’ (Factory Position OFF).

CONTROL STATUS LED: Yellow LED indicates control switch is on AUTO.

SURGE STATUS: Provides remote notification of surge status (customer provided closure).

REMOTE CONTROL TERMINAL BLOCK: This terminal block will activate the receptacle with a

dry contact closure (customer provided closure). The control power is provided by the modules’

internal 12V DC power supply.

‘NORMALLY OPEN’ or ‘NORMALLY CLOSED’ control selection switch.

CIRCUIT BREAKER: Press to reset if the circuit breaker trips.

Page 5

M-15A-SP SHOWN

CONNECTIONS, CONTROLS AND INDICATORS (M SERIES)

DUPLEX RECEPTACLE: All Modules contain one duplex receptacle.

15A Models - (NEMA 5-15R)

20A Models - (NEMA 5-20R)

CIRCUIT BREAKER: Press to reset if the circuit breaker trips.

SERIES PROTECTED

15 AMP MODULE

120V - 12A - 60Hz

M-15A-SP

RESET

Conforms to UL Standard

1449

Certified to CSA Standard

C22.2 No. 8

Page 6

1) Insert the flange on the module into the raceway. (FIGURE A)

2) Place the module into raceway. (FIGURE B)

3) Screw the module to the raceway (FIGURE C).

USE A HAND-HELD SCREWDRIVER AND DO NOT OVERTIGHTEN

FIGURE C

FIGURE A

FIGURE B

INSTALLATION OF MODULE TO RACEWAY

Page 7

INSTALLATION OF MODULE TO RACEWAY

Please note that there is a separate input and output for this module. The bottom of the circuit

board is shown below denotes the input/output.

Page 8

WARRANTY

Middle Atlantic Products (the "Company") warrants the Series Protection Module to be free from defects in material or workmanship under normal use and conditions for a period of three (3) years from the

date of shipment by the company.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and

refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection

thereof at the Company's factory.

This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty

does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE

OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER

PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.

Corporate Headquarters Middle Atlantic Canada Factory Distribution

Corporate Voice 973-839-1011 - Fax 973-839-1976 Voice 613-836-2501 - Fax 613-836-2690 USA: NJ - CA - IL Canada: ON - BC

International Voice +1 973-839-8821 - Fax +1 973-839-4982 middleatlantic.ca - [email protected]

middleatlantic.com - [email protected]

WARRANTY

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Middle Atlantic Unité de contrôle