Microchip Technology SAM E70 Xplained Ultra Manuel utilisateur
SAM E70 Xplained Ultra User's Guide
Introduction
This user’s guide provides detailed information about the SAM E70 Xplained Ultra Evaluation kit and its
various features. Figure below illustrates the SAM E70 Xplained Ultra Evaluation kit.
Figure 1. SAM E70 Xplained Ultra Evaluation Kit with PHY Daughter Board
Features
• ATSAME70Q21 Microcontroller
• One Mechanical Reset Button
• One Mechanical User Push Button
• Two User LEDs
• 12.0 MHz Oscillator (DSC6003)
• 32.768 kHz Oscillator (DSC6083)
• 2-MB SDRAM
• 4-MB QSPI Flash (SST26VF032BA)
© 2019 Microchip Technology Inc. DS70005389A-page 1
• Ethernet Interface with External IEEE 802.3az 10Base-T/100Base-TX Ethernet RMII PHY on a
Daughter Board
• AT24MAC402 256KB EEPROM with EUI-48 Address
• ATA6561 CAN Transceiver
• Micro SD Card Connector with SDIO Support
• Camera Interface Connector
• Two Xplained Pro Extension Headers
• Graphics Card Interface
• CoreSight® 20 Connector for 4-bit ETM
• Arduino MEGA Shield Connector
• External Debugger Connector
• USB Interface, Device and Host Mode
• Embedded Debugger:
– Programming and debugging through USB interface
– Auto-ID for board identification in Atmel Studio and MPLAB® X
– One yellow status LED
– One green board power LED
– Symbolic debug of complex data types including scope information
– Data Gateway Interface: SPI, I2C, four GPIOs
– Virtual COM port (CDC)
• External Power Input (5-14V) or USB Power
• X32 Daughter Board Interface to Support Audio and Bluetooth®
• One mikroBus™ Interface
Kit Overview
The Microchip PIC32 SAM E70 Xplained Ultra Development Kit (DM320113) provides a modular
development system for Microchip’s line of 32-bit Cortex® microcontrollers.
For a free Microchip demonstration code and additional information, visit the MPLAB Harmony™ web
page at: http://www.microchip.com/MPLABHarmony.
The Atmel SAM E70 Xplained Ultra Dvelopment Kit is a hardware platform to evaluate the Microchip
ATSAME70Q21. The kit offers a set of features that enables the ATSAME70Q21 users to start with the
SAM E70 peripherals and understand how to integrate the device in their design.
The SAM E70 Xlpained Ultra kit contains the following items:
• One SAM E70 Xplained Ultra Development Kit
• One KSZ8061 Ethernet PHY
• One Graphics card set up for 565 (16-bit color) graphics
Note: If any items are missing in the kit, contact Microchip sales office for assistance. A list of Microchip
Sales offices is provided on the last page of this document.
The figure below illustrates the SAM E70 Xplained Ultra Evaluation Kit features.
© 2019 Microchip Technology Inc. DS70005389A-page 2
Figure 2. SAM E70 Xplained Ultra Evaluation Kit
© 2019 Microchip Technology Inc. DS70005389A-page 3
The table below provides the SAM E70 Xplained Ultra Evaluation kit feature descriptions.
Table 1. SAM E70 Xplained Ultra Evaluation Kit Feature and Location
Number Description
1 CAN interface
2 X32 Daughter Board interface
3 Mikro interface
4 Ethernet PHY interface
5 Ethernet Clock enable/disable jumper
1. Shorted = disabled
2. Open = enabled
6 EXT1/EXT2 interface
7 Debugger USB
1. Programming
2. Power
3. DGI
8 External Reset Button
9 User Button
10 MCU current measurement jumper
11 SAM E70 Host/Device USB
12 CoreSite® 20 (SWD + ETM) debugging interface
13 Barrel power input (2.1mm)
14 User defined LEDs
15 LED2/USB detect jumper
16 Image Sensor interface
17 SWD debugger interface
18 Graphics card interface
19 ATSAME70Q21B
20 SQI external Flash memory
© 2019 Microchip Technology Inc. DS70005389A-page 4
Table of Contents
Introduction......................................................................................................................1
1. Getting Started.......................................................................................................... 6
2. Xplained Ultra............................................................................................................ 8
3. Embedded Debugger................................................................................................ 9
3.1. Hardware Identification System....................................................................................................9
4. System Level Block Diagram...................................................................................11
5. Hardware Features..................................................................................................12
5.1. Xplained Pro Standard Extension Header..................................................................................12
5.2. Graphics Connectors or GFX Card Interface............................................................................. 13
5.3. SDRAM and LCD Connections.................................................................................................. 16
5.4. Camera Connector.....................................................................................................................18
5.5. USB Connectivity....................................................................................................................... 19
5.6. Chip Erase Header.....................................................................................................................20
5.7. Audio Connectivity......................................................................................................................20
5.8. mikroBUS™ Header................................................................................................................... 22
5.9. CAN............................................................................................................................................22
5.10. Ethernet......................................................................................................................................23
5.11. Debug USB Connectivity............................................................................................................24
5.12. Switches.....................................................................................................................................24
5.13. AT24MAC402 Serial EEPROM.................................................................................................. 25
5.14. Power Sources...........................................................................................................................26
6. Hardware................................................................................................................. 28
6.1. SAM E70 Xplained Ultra Development Board Schematics........................................................ 28
6.2. Bill of Materials...........................................................................................................................50
The Microchip Web Site................................................................................................ 55
Customer Change Notification Service..........................................................................55
Customer Support......................................................................................................... 55
Microchip Devices Code Protection Feature................................................................. 55
Legal Notice...................................................................................................................56
Trademarks................................................................................................................... 56
Quality Management System Certified by DNV.............................................................57
Worldwide Sales and Service........................................................................................58
© 2019 Microchip Technology Inc. DS70005389A-page 5
1. Getting Started
SAM E70 Xplained Ultra Evaluation Quick Start
Follow these steps to explore the Atmel SAM E70 Xplained Ultra evaluation kit:
1. Download and install MPLAB X.
2. Launch MPLAB X.
3. Install MPLAB Harmony 3™.
When Microchip SAM E70 Xplained Ultra is connected to the computer for the first time, the operating
system will install a driver software. The driver file supports both 32-bit and 64-bit versions of Microsoft®
Windows® XP/ Vista /7/8/10.
Once the kit is powered, the green power LED will be lit and MPLAB X will auto-detect the kit and identify
which Xplained Pro extension boards are connected. MPLAB X will provide relevant information like data
sheets and kit documentation. The SAM E70 device is programmed and debugged by the on-board
Embedded Debugger, hence no external programmer or debugger tool is needed.
Design Documentation and Relevant Links
The following list provides links to the relevant documents and software for the SAM E70 Xplained Ultra.
• Xplained Pro products
– Atmel Xplained Pro is a series of small-sized and easy-to-use evaluation kit for Microchip
microcontrollers and other Microchip products. It consists of a series of low-cost MCU boards for
evaluation and demonstration of features and capabilities of different MCU families.
• Microchip MPLAB® Integrated Development Environment
– A free Microchip MPLAB IDE for development of C/C++ and assembler code for Microchip
microcontrollers.
• MPLAB Harmony™
– A free MPLAB Harmony code base is available for user application. The latest MPLAB Harmony
code is available for download at:http://www.microchip.com/MPLABHarmony.
• EDBG User Guide
– This user’s guide provides additional information about the on-board Embedded Debugger.
• Data Visualizer
– Data Visualizer is a program used for processing and visualizing data. The Data Visualizer can
receive data from various sources, such as the Embedded Debugger Data Gateway Interface
that is found on the Xplained Pro boards and COM ports.
• IAR Embedded Workbench® for ARM®
– A commercial C/C++ compiler that is available for ARM. A 30-day evaluation version and a code
size limited kick-start version are also available for download from their web site. The code size
limit is 16-KB for devices with M0, M0+, M1 cores, and 32-KB for devices with other cores.
• Keil MDK-ARM Microcontroller Development Kit
– The MDK-ARM is a complete software development environment for Cortex®-M, Cortex-R4,
ARM7™, and ARM9™ processor-based devices. The MDK-ARM is specifically designed for
microcontroller applications, it is user friendly yet powerful enough for the most demanding
embedded applications.
• Design Documentation
Getting Started
© 2019 Microchip Technology Inc. DS70005389A-page 6
– Package containing schematics, BOM, assembly drawings, 3D plots, layer plots, and so on.
• Hardware Users Guide
– PDF version of this user guide.
Getting Started
© 2019 Microchip Technology Inc. DS70005389A-page 7
2. Xplained Ultra
The SAM E70 Xplained Ultra implements several Xplained Pro standards like extension headers and
connectors. Xplained Pro is an evaluation platform that provides a full Microchip microcontroller
experience. The platform consists of a series of Microcontroller (MCU) boards and extension boards that
are integrated with the Microchip MPLAB IDE that supports data streaming. The Xplained Pro MCU
boards support a wide range of Xplained Pro extension boards, such as audio DACs/CODECs, Ethernet
PHYs, graphics cards, and mikroBUS™ that are connected through a set of standardized headers and
connectors. Each extension board has an identification (ID) chip to uniquely identify which boards are
connected to a Xplained Pro MCU board. This information is used to present relevant user guides,
application notes, data sheets, and example code through MPLAB X.
Xplained Ultra
© 2019 Microchip Technology Inc. DS70005389A-page 8
3. Embedded Debugger
The SAM E70 Xplained Ultra contains Microchip Embedded Debugger (EDBG) for on-board debugging.
The EDBG is a composite USB device, which is based on the following interfaces:
• Debugger
• Virtual COM Port
• Data Gateway Interface (DGI)
Together with the Microchip MPLAB IDE, the EDBG debugger interface can program and debug the
ATSAME70Q21. On the SAM E70 Xplained Ultra, the SWD interface is connected between the EDBG
and the ATSAME70Q21.
The Virtual COM Port is connected to a UART on the ATSAME70Q21 and provides an easy way to
communicate with the target application through the terminal software. It offers variable baud rate, parity,
and Stop bit settings. The settings on the ATSAME70Q21 must match the settings given in the terminal
software.
Note: If not set automatically, Data Terminal Ready (DTR) must be set in the terminal software.
The DGI consists of several physical interfaces for communication with the host computer.
Communication over the interfaces is bidirectional. It can be used to send events and values from the
ATSAME70Q21, or as a generic printf-style data channel. Traffic over the interfaces can be timestamped
on the EDBG for accurate tracing of events. Note that timestamping imposes an overhead that reduces
maximal throughput. The Data Visualizer is used to send and receive data through DGI.
The EDBG controls two LEDs on SAM E70 Xplained Ultra: a power LED and a status LED.
The following table describes how the LEDs are controlled in different operation modes.
Table 3-1. EDBG LED Control
Operation Mode Power LED Status LED
Normal operation The power LED is lit when power is
applied to the board.
Activity indicator, LED flashes when any
communication happens to the EDBG.
Bootloader mode
(idle)
The power LED and the status LED
blinks simultaneously.
The power LED and the status LED
blinks simultaneously.
Bootloader mode
(firmware upgrade)
The power LED and the status LED
blinks in an alternating pattern.
The power LED and the status LED
blinks in an alternating pattern.
For additional information on EDBG, refer to the EDBG User Guide.
3.1 Hardware Identification System
All Xplained Pro-compatible extension boards have an Microchip ATSHA204 CryptoAuthentication™ chip
mounted. This chip contains information that identifies the extension with its name and data. When an
Xplained Pro extension is connected to an Xplained Pro MCU board, the information is read and sent to
the MPLAB X IDE. The Microchip kits extension, installed with MPLAB X, provides relevant information,
such as code examples, and links to relevant documents. The following table provides the data fields
stored in the ID chip with content examples.
Embedded Debugger
© 2019 Microchip Technology Inc. DS70005389A-page 9
Table 3-2. Xplained Pro ID Chip Content Example
Data Field Data Type Example
Manufacture ASCII string Microchip’\0’
Product Name ASCII string
Product Revision ASCII string 04’\0’
Product Serial number ASCII string 1774020200000010’\0’
Minimum Voltage (mV) uint16_t 3000
Maximum Voltage (mV) uint16_t 3600
Maximum Current (mA) uint16_t 30
Embedded Debugger
© 2019 Microchip Technology Inc. DS70005389A-page 10
Table des matières
Autres manuels Microchip Technology Carte mère
Microchip Technology
Microchip Technology CEC1x02 Manuel utilisateur
Microchip Technology
Microchip Technology MCP19035 Manuel utilisateur
Microchip Technology
Microchip Technology EVB-KSZ8563 Manuel utilisateur
Microchip Technology
Microchip Technology EVB-KSZ9563 Manuel utilisateur
Microchip Technology
Microchip Technology MCP251XFD CAN FD Manuel utilisateur
Microchip Technology
Microchip Technology MCP19114 Manuel utilisateur
Microchip Technology
Microchip Technology MIC38300 Manuel utilisateur
Microchip Technology
Microchip Technology PIC32 Family Manuel utilisateur
Microchip Technology
Microchip Technology HV7358DB1 Manuel utilisateur
Microchip Technology
Microchip Technology PAC1934 Manuel utilisateur
Microchip Technology
Microchip Technology ATtiny416 Xplained Nano Manuel utilisateur
Microchip Technology
Microchip Technology MIC7401 Manuel utilisateur
Microchip Technology
Microchip Technology MCP1252 Manuel utilisateur
Microchip Technology
Microchip Technology ADM00592 Manuel utilisateur
Microchip Technology
Microchip Technology dsPICDEM 1.1 Plus Manuel utilisateur
Microchip Technology
Microchip Technology PICDEM Touch Sense 2 Manuel utilisateur
Microchip Technology
Microchip Technology SOT23-6 Manuel utilisateur
Microchip Technology
Microchip Technology ATtiny817 Xplained Pro Manuel utilisateur
Microchip Technology
Microchip Technology MCP73213 OVP Manuel utilisateur
Microchip Technology
Microchip Technology PIC32MX470 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
