Microchip Technology ATSAMA5D2-ICP Manuel utilisateur
ATSAMA5D2-ICP
SAMA5D2 Industrial Connectivity Platform (ICP) User's
Guide
Scope
This user’s guide describes how to use the SAMA5D2 Industrial Connectivity Platform (SAMA5D2-ICP) kit.
The SAMA5D2-ICP is a hardware and software platform that demonstrates the rich wired and wireless connectivity
solutions around Microchip's SAMA5D2 Arm Cortex-A based microprocessors. It offers customers a starting point for
their applications that include either EtherCAT, Ethernet 10/100 and 10/100/1000, CAN, Wi-Fi®, Bluetooth® or USB
communications, or any combination of these. The board also features three mikroBUS™ click interface headers to
support over 450 MikroElektronika Click boards™.
Figure 1. SAMA5D2-ICP Board
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 1
Table of Contents
Scope............................................................................................................................................................. 1
1. Introduction............................................................................................................................................. 3
1.1. Document Layout......................................................................................................................... 3
1.2. Reference Documents..................................................................................................................3
2. Product Overview....................................................................................................................................4
2.1. SAMA5D2-ICP Features.............................................................................................................. 4
2.2. SAMA5D2-ICP Kit Content...........................................................................................................5
2.3. Evaluation Kit Specifications........................................................................................................ 5
2.4. Power Sources............................................................................................................................. 5
3. Board Components................................................................................................................................. 6
3.1. Board Overview............................................................................................................................6
3.2. Function Blocks............................................................................................................................ 8
3.3. External Interfaces..................................................................................................................... 43
3.4. Debugging Capability................................................................................................................. 45
3.5. PIO Usage on Expansion Connectors........................................................................................50
4. Board Layout.........................................................................................................................................55
5. Installation and Operation..................................................................................................................... 57
5.1. System and Configuration Requirements...................................................................................57
5.2. Board Setup............................................................................................................................... 57
6. Revision History.................................................................................................................................... 58
6.1. Rev. A - 02/2020.........................................................................................................................58
The Microchip Website.................................................................................................................................59
Product Change Notification Service............................................................................................................59
Customer Support........................................................................................................................................ 59
Product Identification System.......................................................................................................................60
Microchip Devices Code Protection Feature................................................................................................ 60
Legal Notice................................................................................................................................................. 60
Trademarks.................................................................................................................................................. 60
Quality Management System....................................................................................................................... 61
Worldwide Sales and Service.......................................................................................................................62
ATSAMA5D2-ICP
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 2
1. Introduction
1.1 Document Layout
The document is organized as follows:
• Introduction
• Product Overview—Important information about the kit
• Board Components—Kit specifications and high-level description of the major components and interfaces
• Board Layout—Drawings
• Installation and Operation—Information on requirements and setup
1.2 Reference Documents
The following reference data sheets are available on www.microchip.com:
Table 1-1. SAMA5D2-ICP Component Data Sheets
Document Title Available Document Ref.
SAMA5D2 Series https://www.microchip.com/ATSAMA5D27 DS60001476
MCP16502 https://www.microchip.com/MCP16502 DS20006275
PAC1932/3/4 https://www.microchip.com/PAC1934 DS20005850
SST26VF064B/SST26VF064BA https://www.microchip.com/
SST26VF064B
DS20005119
24AA02E48/24AA025E48/24AA02E64/24AA025E64 https://www.microchip.com/24AA025E48 DS20002124
MCP2542FD/4FD, MCP2542WFD/4WFD https://www.microchip.com/MCP2542FD DS20005514
USB2534 https://www.microchip.com/USB2534 DS00001713
MIC2026/2076 https://www.microchip.com/MIC2026 M9999-060410-B
LAN7850 https://www.microchip.com/LAN7850 DS00001993
KSZ8563R https://www.microchip.com/KSZ8563 DS00002418
LAN9252 https://www.microchip.com/LAN9252 DS00001909
24AA512/24LC512/24FC512 https://www.microchip.com/24FC512 DS21754
ATWILC3000-MR110CA https://www.microchip.com/ATWILC3000 DS70005327
93AA66A/B/C, 93LC66A/B/C, 93C66A/B/C https://www.microchip.com/93AA66A DS21795
ATECC608A https://www.microchip.com/ATECC608A DS40001977
ATSAMA5D2-ICP
Introduction
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 3
2. Product Overview
The SAMA5D2 Industrial Connectivity Platform (SAMA5D2-ICP) provides a versatile Total System Solutions platform
that highlights Microchip’s MPU and connectivity ICs for industrial networking applications.
The board features three mikroBUS click interface headers to support over 450 MikroElektronika Click boards and
provisions to solder a Microchip ATWILC3000-MR110CA or a ATWILC3000-MR110UA WiFi/BT module.
2.1 SAMA5D2-ICP Features
Table 2-1. SAMA5D2-ICP Features
Characteristics Specifications Components
Processor SAMA5D27-CU (289-ball BGA), 14x14 mm body, 0.8 mm
pitch _
External Clocks
MPU: 12 MHz, 32.768 kHz
Misc osc: 12, 24, 25 MHz Oscillators and optional crystal
Memory
Two 16-bit, 2-Gbit DDR3L (total of 512 Mbytes)
One QSPI Flash
Three EEPROMs
Winbond® W632GU6MB
Microchip SST26VF064B
Microchip 24AA025E48
SD/MMC One standard SD card interface SD card connector
USB
One USB host switch 4 ports with power switch
One USB device type Micro-AB Microchip USB2534
CAN Two CAN interfaces Microchip MCP2542FDT
Ethernet
One Gigabit Ethernet PHY through HSIC
One ETH switchport
One EtherCAT interface
Microchip LAN7850T-I/8JX
Microchip KSZ8563RNXI
Microchip LAN9252I/ML
Wi-Fi/BT
Footprint for IEEE® 802.11 b/g/n Wi-Fi plus Bluetooth
Module (Wi-Fi/BT), suitable for Microchip WILC3000-
MR110CA or WILC3000-MR110UA
–
Debug port
One J-Link-OB/J-Link-CDC
One JTAG interface
Embedded J-Link-OB and J-Link-
CDC (ATSAM3U4C TFBGA100)
Board monitor
One RGB (Red, Green, Blue) LED
DisableBoot, Reset, WakeUp, 2 x User Free push button
switches
Common anode RGB LED
5 push button switches
Expansion
One PIOBU/PIO connector
Three mikroBUS sockets
–
–
Power management
One PMIC
One power consumption measurement device
Microchip MCP16502
Microchip PAC1934
Board supply From J16 and from external connector µUSB and 2.1mm/5.5mm jack
connector
ATSAMA5D2-ICP
Product Overview
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 4
2.2 SAMA5D2-ICP Kit Content
The SAMA5D2-ICP kit includes the following:
• one SAMA5D2-ICP board
• one USB male A to USB male Micro-B cable
2.3 Evaluation Kit Specifications
Table 2-2. Evaluation Kit Specifications
Characteristic Specification
Board SAMA5D2-ICP
Board supply voltage External and USB-powered
Temperature Operating: 0°C to +70°C
Storage: –40°C to +85°C
Relative humidity 0 to 90% (non-condensing)
Main board dimensions 150 × 100 × 20 mm
RoHS status Compliant
Board identification SAMA5D2-ICP Industrial Connectivity Platform
2.4 Power Sources
Two options are available to power up the SAMA5D2-ICP board:
• Through an external AC to DC +5V wall adapter connector (J1 – default configuration)
• Through the USB Micro-AB connector on the J-Link-OB Embedded Debugger interface (J16)
Table 2-3. Electrical Characteristics
Electrical Parameter Value
Input voltage 5VCC
Maximum input voltage (limits) 6VCC
Maximum DC 3.3V current available 1.2A
I/O voltage 3.3V only
ATSAMA5D2-ICP
Product Overview
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 5
3. Board Components
This section covers the specifications of the SAMA5D2-ICP and provides a high-level description of the board’s major
components and interfaces. This document is not intended to provide a detailed documentation about the processor
or about any other component used on the board. For detailed device documentation, refer to Reference Documents.
3.1 Board Overview
The fully-featured SAMA5D2-ICP board integrates multiple peripherals and interface connectors as shown in the
figure below. J2, indicated in red below, offers current measurement connectivity. J19 and J20, indicated in blue, are
configuration items.
Figure 3-1. Board Overview
3.1.1 Default Jumper Settings
The following table shows the default jumper settings.
Table 3-1. SAMA5D2-ICP Jumper Settings
Jumper Default Function
J2 Closed VDDBU current measurement
J17 Open Erases SAM3U firmware (not populated, reserved for factory configuration, should never be
used by the end user).
J19 Open Enables JTAG-OB (closed=disables JTAG-OB)
J20 Open Enables JTAG-CDC (closed=disables JTAG-CDC)
ATSAMA5D2-ICP
Board Components
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 6
3.1.2 On-Board Connectors
The following table describes the interface connectors on the SAMA5D2-ICP.
Table 3-2. SAMA5D2-ICP Board Interface Connectors
Connector Interfaces to Connector Interfaces to
J1 External power jack J14 EtherCAT RJ45 port B
J3 PMIC Vout4 J15 PCB connector for factory-programming
the J-Link-OB
J4 Used for one-time programming of the
EtherCAT EEPROM J16 USB Micro-AB J-Link-OB/J-Link-CDC
J5 Standard SDMMC connector J18 JTAG, 10-pin IDC connector
J6 Dual CAN J21 mikroBUS1 connector
J7 Stacked USB type B (USB hub) J22 mikroBUS2 connector
J8 Stacked USB type B (USB hub) J23 mikroBUS3 connector
J9 USB Micro-AB (USB-A) J24 Tampers and PIOs
J10 Ethernet 10/100/1000 RJ45 (HSIC) J25 WILC3000 UART debug
J11 Ethernet 10/100 RJ45 (Etherswitch Port1) J26 WILC3000 user-free GPIOs
J12 Ethernet 10/100 RJ45 (Etherswitch Port2) J27 ETH switch user-free GPIOs
J13 EtherCAT RJ45 port A –
ATSAMA5D2-ICP
Board Components
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 7
3.2 Function Blocks
Figure 3-2. SAMA5D2-ICP Block Diagram
Memoryinterface
Power generationPower Measurement
Clock
Module Wifi
DEBUGconnectors
User Interface
EtherCAT
USB Host switch
Dual Ethernet port switch
HSIC to Gigabit ETH
MikroBUS
ATSAMA5D27C-CU
5V input
USBµAB Device
to 4 port USB
QSPISerialFlash
Serial EEPROM
2x16bit 2Gb DDR3L
SDMMC
Wi-Fi Module
3.2.1 Power Supply Topology and Power Distribution
3.2.1.1 Input Power Options
Two options are available to power up the SAMA5D2-ICP board:
1. an external AC to DC +5V wall adapter connected via a 2.1 mm center-positive plug into the board’s power
jack (J1). The recommended output voltage of the power adapter is 5V at 2A.
2. the USB J-Link-OB port (J16)
The +5V from the wall adapter is protected through an NCP349 positive overvoltage controller switch. The controller
is able to disconnect the system from its output pin when incorrect input operating conditions are detected (5.83V
max).
The USB-powered operation comes from the USB J-Link-OB port connected to a PC or a 5V DC supply. The USB
supply is sufficient to power the board in most applications. It is important to note that when the USB supply is used,
the USB port has limited power. If the USB host port is required for the application, it is recommended to use the
external DC supply.
The red D3 ON LED indicates the presence of a 5V power supply from the wall adapter or from USB.
The figure below shows the input power supply topology.
ATSAMA5D2-ICP
Board Components
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 8
Figure 3-3. Input Powering
2.1mm
2
3
1
J1
10k
R12
100k
0402
R13
GND
1uF
16V
0603
C1
GND
0.1uF
16V
C6
0.1uF
16V
0402
C19
GND
100k
0402
R11
0.1uF
16V
0402
C4
GND
VBUS_JLINK
VDD_MAIN_5V
GND
IN
1
IN_PAD
7
EN
6
GND
2FLAG 3
OUT2 5
OUT1 4
NCP349MNAETBG
U1
GND
RED
D3
2.2k
R14
220uF
10V
AL-D8
C290
GND
2
71
6
Q1A
SIA923AEDJ-T1-GE3
5
8 4
3
Q1B
SIA923AEDJ-T1-GE3
2
71
6
Q2A
SIA923AEDJ-T1-GE3
5
8 4
3
Q2B
SIA923AEDJ-T1-GE3
180R
FB26
Earth USB GND
VBUS_JLINK
ID 4
VBUS 1
GND 5
D- 2
D+ 3
0
0475890001
J16
USB MicroAB
USBD_JLINK_P
USBD_JLINK_N
USB-powered operation eliminates additional wires and batteries. It is the preferred mode of operation for any project
that requires only a 5V source at up to 500 mA.
Figure 3-4. Power Supply Connector and USB J-Link-OB Port Location
3.2.1.2 Power Supply Requirements and Restrictions
Detailed information on the device power supplies is provided in tables “SAMA5D2 Power Supplies” and “Power
Supply Connections” in the SAMA5D2 Series data sheet.
ATSAMA5D2-ICP
Board Components
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 9
3.2.1.3 Power-Up and Power-Down Considerations
Power-up and power-down considerations are described in section “Power Considerations” in the SAMA5D2 Series
data sheet.
3.2.1.4 Power Management
The board power management uses a Microchip PMIC, MCP16502. This is a complete, cost-effective and highly-
efficient power management solution, optimized to provide a single-chip power solution and voltage sequencing for
Microchip’s MPU series.
The MCP16502AA features:
• Four DC-DC buck regulators. Each buck channel can support loads up to 1A. Each DC-DC regulator is
optimized for its target load, namely:
– Buck 1: 3.3V for I/Os and other analog loads
– Buck 2: 1.35V for DDR3L voltage
– Buck 3: 1.25V for core voltage
– Buck 4 is unused for this application, can be accessed by users via J3 connector.
• Two 300 mA LDOs, 2.5V for VDDFUSE and 3.3V for RGB LEDs
• Support of Hibernate, Low-Power and High-Performance modes
• Interrupt flag, control PIOs and I2C interface
The default power channel sequencing is built-in, according to the requirements of the MPU. A dedicated pin (LPM)
facilitates the transition to Low-Power modes. The MCP16502 features a low no-load operational quiescent current
and draws less than 10 µA in full shutdown. Active discharge resistors are provided on each output. All buck
channels support safe start-up into pre-biased outputs.
3.2.1.4.1 Configuration
Buck 2 default voltage is selected by means of the hardwired SELV2 pin and cannot be changed on-the-fly during
operation (high-Z 1.35V DDR3L).
LDO1 default voltage is selected by means of the hardwired SELVL1 pin and cannot be changed on-the-fly during
operation (high-Z 2.5V VDDFUSE).
3.2.1.4.2 Interfacing Signals
The MCP16502 is interfaced to the host MPU by means of the following signals:
• nSTRTO (open-drain output)
• nRSTO (open-drain output)
• nINTO (open-drain output)
• PWRHLD (input)
• LPM (input) and HPM (input)
• SDA and SCL (I2C interface pins)
Note: The MCP16502 is a slave-only device without clock stretching capability. Therefore, the SCL pin is an input
only.
3.2.1.4.3 nSTRT, nSTRTO, PWRHLD Functionality
The nSTRT (push button input) serves as an external initialization input to the PMIC. nSTRT is internally pulled up to
SVIN and monitored. When the nSTRT is pulled/detected LOW (SW3 pressed), the MCP16502 initiates the turn-on
sequence.
The nSTRTO signal is asserted LOW whenever the nSTRT is detected to be LOW, and it is high-Z otherwise
(nSTRTO has an external pull-up resistor).
While nSTRT is LOW during the power-up sequence, the MCP16502 expects the assertion of the PWRHLD signal
(power-hold) from the MPU to continue the sequence.
PWRHLD may be already HIGH in a typical application using a backup supply. If PWRHLD has NOT been asserted
HIGH by the MPU before completion of the start-up sequence (i.e., when nRSTO is asserted high), the MCP16502
automatically initiates a turn-off sequence.
After the assertion of PWRHLD, nSTRT should be released before the long-press time-out timer expires.
ATSAMA5D2-ICP
Board Components
© 2020 Microchip Technology Inc. User Guide DS60001592A-page 10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Microchip Technology Carte mère
Microchip Technology
Microchip Technology EVB-USB4715 Manuel utilisateur
Microchip Technology
Microchip Technology HV2903 Manuel utilisateur
Microchip Technology
Microchip Technology PAC1921 Manuel utilisateur
Microchip Technology
Microchip Technology EVB-LAN9370 Manuel utilisateur
Microchip Technology
Microchip Technology MPLAB ICE Manuel utilisateur
Microchip Technology
Microchip Technology Microsemi PD70201EVB-25F-D-5 Manuel utilisateur
Microchip Technology
Microchip Technology ATtiny416 Xplained Nano Manuel utilisateur
Microchip Technology
Microchip Technology AT42QT1010 Manuel utilisateur
Microchip Technology
Microchip Technology PIC32MK Manuel utilisateur
Microchip Technology
Microchip Technology PIC18F47K42 Curiosity Nano Manuel d'installation
Microchip Technology
Microchip Technology PICDEM 2 Plus Manuel utilisateur
Microchip Technology
Microchip Technology MCP39F501 Manuel utilisateur
Microchip Technology
Microchip Technology EVB-KSZ9563 Manuel utilisateur
Microchip Technology
Microchip Technology EV20F92A Manuel utilisateur
Microchip Technology
Microchip Technology MCP19117 Manuel utilisateur
Microchip Technology
Microchip Technology SAM-IoT Wx v2 Manuel d'installation
Microchip Technology
Microchip Technology dsPICDEM MCHV Manuel utilisateur
Microchip Technology
Microchip Technology MIC24045 Manuel utilisateur
Microchip Technology
Microchip Technology SAMA5D3 XPLAINED Manuel utilisateur
Microchip Technology
Microchip Technology EVB-USB5744 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
