September 2002 7 MICRF102
MICRF102 Micrel
Applications Information
Design Process
The MICRF102 transmitter design process is as follows:
1). Set the transmit frequency by providing the
correct reference oscillator frequency
2). Ensure antenna resonance at the transmit
frequency by:
LANT = 0.2 ×Length ×ln(Length/d - 1.6) ×10-9 ×k
Where:
Length is the total antenna length in mm.
d is the trace width in mm.
k is a frequency correction factor.
LANT is the approximate antenna inductance in
henries.
Note 1. The total inductance however will be a little greater
than the LANT calculated due to parasitics. A 2nH should be
added to the calculated value. The LANT formula is an
approximatedwaytocalculatetheinductanceoftheantenna.
The inductance value will vary however, depending on pcb
material,thickness,groundplane,etc.Themostpreciseway
to measure is to use a RF network analyzer.
3). Calculate the total capacitance using the follow-
ing equation.
CfL
TANT
=×××
()
1
422
ππ
Where:
CTtotal capacitance in farads.
π= 3.1416.
f = carrier frequency in hertz.
LANT inductance of the antenna in henries.
4). Calculate the parallel and series capacitors,
which will resonate the antenna.
4.1). Ideally for the MICRF102 the series and parallel
capacitors should have the same value or as
close as possible.
4.2). Start with a parallel capacitor value and plug in
the following equation.
C
CC C
S
T VAR P
=−+
()
1
11
Where:
CVAR is the center varactor capacitance (5pF for the
MICRF102) in farads.
CPis the parallel capacitor in farads.
CSis the series capacitor in farads.
Repeat this calculation until CSand CPare very close and
they can be found as regular 5% commercial values.
Note2.Ideally,theantennasizeshouldnotbelargerthanthe
oneshownhere. Thebiggertheantennaarea, thehigherthe
loaded Q in the antenna circuit will be. This will make more
difficult to match the parallel and series capacitors. Another
point to take into consideration is the total ac rms current
going through the internal varactor in the MICRF102. This
current should not exceed 16mA rms. The parallel capacitor
will absorb part of this current if the antenna dimensions are
appropriate and not exaggerated larger than the one shown
here.
Note 3. A strong indication that the right capacitor values
havebeenselected is the meancurrent with a1kHz signal in
the ASK pin. Refer to the
Electrical Characteristics
for the
current values.
Note4.Formuch smaller antennas, placeablockingcapaci-
tor for the series capacitance (around 100pF to 220pF) and
usethefollowingformulafortheparallelcapacitanceCT=CP
+ CVAR. The blocking capacitor is needed to ensure that no
dc current flows from one antenna pin to the other.
5.) Set PC pin to the desired transmit power.
Reference Oscillator Selection
Anexternalreferenceoscillatorisrequiredtosetthetransmit
frequency. The transmit frequency will be 32 times the
reference oscillator frequency.
ff
TX REFOSC
=×32
Crystalsorasignalgeneratorcanbeused.Correctreference
oscillator selection is critical to ensure operation. Crystals
must be selected with an ESR of 20 Ohms or less. If a signal
generator is used, the input amplitude must be greater than
200 mVP-P and less than 500 mVP-P.
Antenna Considerations
The MICRF102 is designed specifically to drive a loop an-
tenna. It has a differential output designed to drive an induc-
tive load. The output stage of the MICRF102 includes a
varactor that is automatically tuned to the inductance of the
antenna to ensure resonance at the transmit frequency.
A high-Q loop antenna should be accurately designed to set
the center frequency of the resonant circuit at the desired
transmitfrequency.Anydeviationfromthedesiredfrequency
will reduce the transmitted power. The loop itself is an
inductive element. The inductance of a typical PCB-trace
antennaisdeterminedbythesizeoftheloop,thewidthofthe
antenna traces, PCB thickness and location of the ground
plane.Thetoleranceoftheinductanceissetbythemanufac-
turing tolerances and will vary depending how the PCB is
manufactured.
The MICRF102 features automatic tuning. The MICRF102
automaticallytunesitselftotheantenna,eradicatingtheneed
formanualtuningin production. Italsodynamicallyadaptsto
changesinimpedance inoperationandcompensates forthe
hand-effect.
Automatic Antenna Tuning
The output stage of the MICRF102 consists of a variable
capacitor (varactor) with a nominal value of 5.0pF tunable
over a range from 3pF to 7pF. The MICRF102 monitors the
phase of the signal on the output of the power amplifier and
automaticallytunestheresonantcircuitbysettingthevaractor
value at the correct capacitance to achieve resonance.
