Metrologic Genesis MS7580 Manuel du propriétaire

MS7580 Genesis™

Supplemental Guide for EAS Equipped Models

work may be reproduced, transmitted, or stored in any form or by any means

without prior written consent, except by reviewer, who may quote brief

passages in a review, or provided for in the Copyright Act of 1976.

Trademarks

Metrologic is a registered trademark of Metrologic Instruments, Inc.

Products identified in this document are hereby acknowledged as

trademarks, registered or otherwise, of Metrologic Instruments, Inc. or their

respective companies.

iii

TABLE OF CONTENTS

Introduction

Document Scope .............................................................................................. 1

Optional Accessories ........................................................................................ 1

Installation

Integrated RF EAS Antenna Connection .......................................................... 2

EAS System Connection................................................................................... 3

Checkpoint®EAS System Integration............................................................ 3

Configuration

Imager Configuration for EAS Applications....................................................... 4

Operation

EAS – Tag Deactivation Range ........................................................................ 6

Scanner and Cable Terminations

Scanner Pinout Connections ............................................................................ 8

Cable Connector Configurations....................................................................... 9

Antenna Disconnect.......................................................................................... 9

Limited Warranty ................................................................................................ 10

INTRODUCTION

Document Scope

This guide provides additional information required for the installation,

configuration, and operation of MS7580 models equipped with EAS

(MS7580-118-EAS). This guide is intended to be used in conjunction with the

standard MS7580 Genesis, Presentation Area-Imager, Installation and User’s

Guide (PN 00-02290).

Optional Accessories

Cable Compatibility Warning

The MS7580 requires a cable designed for a 12VDC area imager. Do not

attempt to use any cables other than the specified cables listed below.

Any damage incurred from incorrect cable usage will void the limited warranty

shown on page 10.

EAS Cable Options

Part # Description

The following cables are compatible with Checkpoint System devices.

MX-5S000-E-3 RS232 12V VLink Straight, Black Cable

with Built in Power Jack

MX-5S235-E-3 USB 12V VLink Straight Black Cable with

Built in Power Jack, Non-Locking Type A Connector

VLink Power Supply Options

AC to DC Power Transformer - Regulated 12VDC @ 1.25A output.

46-00862 90VAC to 255VAC United States, Canada and Japan

46-00863 90VAC to 255VAC Continental European

46-00864 90VAC to 255VAC United Kingdom

46-00865 90VAC to 255VAC China

46-00866 90VAC to 255VAC Australia

www.metrologic.com2

INSTALLATION

Integrated RF EAS Antenna Connection

The following instructions are applicable for MS7580-118-EAS kits containing an

RS232, MX-5S000-E-3 cable or a USB, MX-5S235-E-3 cable.

Important: Instructions for host cable connections are located in the MS7580

Genesis Installation and User’s Guide (PN 00-02290) under the

Installation section.

1. Locate the connector cover

on the bottom of the imager’s

stand.

2. Remove the socket screw

securing the connector cover.

A 1.5 mm hex key is supplied.

3. Remove the connector cover

plate by lifting up (©) the end and

sliding the cover to the left (§).

4. Insert the 2-pin box plug (A) into

the receptacle on the imager’s

stand (see Figure 2).

5. Insert the cable’s strain relief (B)

into the channel on the stand

(see Figure 2).

6. Re-install the connector cover.

Slide the tab (C) on the cover

into the space between the box

receptacle and the stand

(see Figure 3).

7. Install the socket screw (D) to

secure the cover to the stand

(see Figure 3).

ure

Figure 2.

Figure 1.

INSTALLATION

EAS System Connection

MS7580-118-EAS models are equipped with an integrated antenna for Electronic

Article Surveillance (EAS) system support. The following information should be

used in conjunction with the manufacturer’s documentation provided with the

EAS system.

Checkpoint® EAS System Integration

Metrologic cables compatible with Checkpoint EAS systems include five

additional wires for device connection. Consult the table below for the

appropriate wire and terminal configuration.

Antenna and Interlock†Connection

Cable

(MX-5S000-E-3 or MX-5S235-E-3) Checkpoint Device

Wire Color Wire Gauge Connection Type

Solid Light Green Thin INTLK + Terminal

Solid Black Thin INTLK - Terminal, GND Interlock†

Red and White Thick Antenna + Terminal

Black and White Thick Antenna - Terminal

No Insulation/Shield Antenna Shield

Antenna

† Interlock functionality requires specific EAS device settings. Consult the

manufacturer’s EAS system documentation for the appropriate switch and timing

potentiometer settings.

Inside the Checkpoint device, two switch banks set the deactivation antenna

tuning. The recommended settings for the switch banks are shown below.

See page 6 for tag deactivation guidelines.

Switch Bank Settings

SW1 SW2

Switches 1 - 6 OFF Switches 1 - 6 OFF

Settings of 0pF to 47pF are recommended to achieve a maximum

deactivation range.

Checkpoint®is a registered trademark of Checkpoint Systems, Inc.

www.metrologic.com4

CONFIGURATION

Imager Configuration for EAS Applications

EAS support is disabled by default in the MS7580 series. To enable EAS

support the imager must be configured for a system type and signal mode.

Follow the configuration sequence below to configure the imager for EAS

functionality.

1. Scan the system type bar code below to enable EAS system support.

Enable Checkpoint System EAS Support

³337220

To disable EAS support, scan the Disable EAS Support bar

code below.

Disable EAS Support

³337200

2. Scan either the Enable Continuous Mode bar code or the Enable

Regular Mode bar code.

Enable

Regular Mode

In regular EAS mode, the imager will signal

the EAS system to activate immediately after

the area imager successfully transmits a bar

code. The area imager will signal the EAS

system to deactivate after the configured

EAS timeout expires.

³146105

Enable

Continuous Mode

In continuous mode, the imager will signal

the EAS system to activate when it first

powers on. The area imager will never

deactivate the EAS system while in

continuous mode.

The EAS timeout setting has no effect in

continuous mode.

³146115

CONFIGURATION

3. Scan the desired EAS timeout length (applicable for regular mode only).

The EAS timeout length specifies the maximum time that the area

imager will leave the EAS interlock signal asserted following a

successful scan.

If the area imager commonly fails to deactivate EAS tags,

try increasing the value of the timeout setting.

Note: The EAS timeout setting has no effect in continuous

mode.

EAS Timeout 100 ms

³846000

EAS Timeout 500 ms

³846050

EAS Timeout 1s

³8460100

EAS Timeout 5s

³8460500

www.metrologic.com6

OPERATION

EAS – Tag Deactivation Range

Antenna Precaution:

The integrated EAS antenna is built into the stand/base of the imager.

Do not enclose or rest the imager’s base in close proximity to dense

metal. The metal may interfere with the antenna decreasing the

expected deactivation range.

Tag Storage Precaution:

Do not store tags within 45.7 cm [18.0″] of the MS7580. Tags stored

closer than 45.7 cm [18.0″] may be unintentionally deactivated. The

precautionary area includes storage areas located under the MS7580.

Proper tag deactivation requires the entire tag to pass through the expected

tag deactivation range indicated in figures 4 and 5.

Figure 4. Expected Tag Deactivation Area (Side View)

Specifications are subject to change without notice.

Autres manuels pour Genesis MS7580

Table des matières

Autres manuels Metrologic Lecteur de codes-barres

Metrologic

Metrologic Cubit IS6520 Series Manuel utilisateur

Metrologic

Metrologic TECH 8 Manuel utilisateur

Metrologic

Metrologic StratosS MS2220 Manuel utilisateur

Metrologic

Metrologic MK1690-61A38 Manuel utilisateur

Metrologic

Metrologic MS1633 FocusBT Manuel utilisateur

Metrologic

Metrologic MS5100 Eclipse Series Manuel utilisateur

Metrologic

Metrologic MS9520 Voyager Manuel utilisateur

Metrologic

Metrologic TECH 7 Manuel utilisateur

Metrologic

Metrologic MS860i Mini-Slot Manuel utilisateur

Metrologic

Metrologic IS3480-00 Manuel utilisateur

Metrologic

Metrologic MS770 Manuel utilisateur

Metrologic

Metrologic Stratos MS2422 Manuel utilisateur

Metrologic

Metrologic StratosE MS2122 Manuel utilisateur

Metrologic

Metrologic MLPN 2168 Manuel utilisateur

Metrologic

Metrologic MH941 Manuel utilisateur

Metrologic

Metrologic MK1690-61A38 Manuel utilisateur

Metrologic

Metrologic MK5145-31A38 Manuel utilisateur

Metrologic

Metrologic IS3480 QuantumE Manuel utilisateur

Metrologic

Metrologic MLPN 2159 Manuel utilisateur

Metrologic

Metrologic MK9535-79C5M38 - Metrologic MS9535 VoyagerBT Manuel utilisateur

Metrologic

Metrologic MS6720 Manuel utilisateur

Metrologic

Metrologic Genesis MS7580 Manuel utilisateur

Metrologic

Metrologic Orbit MS7100 Manuel utilisateur

Metrologic

Metrologic MS9500 Voyager Series Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur