MELICONI Fully 8 RC Manuel utilisateur

Fully 8 RC

Keep this booklet for future reference.

Thank you for choosing a Meliconi remote control.

The FULLY 8 RC universal remote control is ideal for replacing up to 8 remote controls of any brand for TV, Digital Terrestrial

(TER), Satellite (SAT) Decoders, DVD players (including Blu Ray), Videotape recorders (VCR), Personal video recorders

(PVR), cable TV (CAB), other audio video equipment (AUX) or decoders for ADSL TV (ADSL). The remote control has a non-

volatile memory, meaning that it does not lose its settings even if there are no batteries in it.

IMPORTANT: the device must not be exposed to excessive heat sources.

USE OF THE BUTTONS AND FUNCTIONS

The functions of the buttons described below are available only if they are also present on the original remote control.

Volume control +/–

TELETEXT buttons

ON/OFF switches the device OFF and

in some cases ON

Numeric keypad

Conﬁrm selection

MUTE

turns sound OFF and ON

For selecting an external input

source

For selecting the next programme P+

or the previous programme P–

For moving around within the MENU

Fastext functions or for selecting

sub-menus using colours

Buttons for selecting the device to be

controlled.

DVD/PVR RECORD PAUSE STOP PLAY

buttons

DVD and PVR forward/back functions

Speciﬁc buttons for decoder

Displays the list of programmes

Selects analogue/digital

Selects digital TV and radio

INSERTING THE BATTERIES

The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries.

Insert them as illustrated.

Try pressing a number button and check that the red light remains lit

continuously until you release the button: if the light ﬂashes, the batteri-

es inserted are not charged and are about to go ﬂat, therefore you must

substitute them.

Do not leave ﬂat batteries inserted, as liquid may leak and damage the remote control

The Fully 8 RC remote control is a universal remote, so its memory contains data relating to numerous devices of various

brands available on the market.

Each original device has a speciﬁc code which must be used to set up the remote control.

Therefore, to use your Fully 8 RC you must enter the speciﬁc code for each device you wish to control.

So use one of the following methods to identify the correct code and set it in your remote control:

A) - INTERNET (recommended)

B) - CELL PHONE (SMS)

C) - MANUAL SEARCH

SETTING CODES

If you have an Internet connection available, follow the on-line guide on the www.meliconi.com/guida website to identify

the speciﬁc codes for the devices you wish to command. Then set the codes manually in your MELICONI remote control

as described in the ENTERING THE CODE DIRECTLY procedure.

SETTING CODES USING INTERNET

Today, Meliconi gives customers who don’t have internet the chance to receive the codes for programming their remote

control directly on their cell phone.

Simply send an SMS to this number 0039 345 7518893 as follows: 8A, Type, Brand, Model

- Type = indicate the device to be controlled using one of the following abbreviations: TV - SAT - DVD - VCR - TER

(Digital Terrestrial decoder) - AUX (other audio video device).

- Brand, Model = to indicate the brand and the model of the device to be controlled.

Example: 8A, TV, PHILIPS, 32PFL3614 (if you don’t know the model, don’t write anything after the brand).

Once you have received the SMS with the list of codes, set the ﬁrst code in the remote control as described in the

ENTERING THE CODE DIRECTLY section.

Stand in front of the device with the MELICONI remote control. Turn the device on and then press the OFF button on the

remote (or the PLAY button if the device is a VCR/DVD).

If the device does NOT switch off (or if the VCR/DVD does not start playing), try setting the consecutive code in the SMS

list in the remote control.

When the device reacts check whether the other buttons are operating correctly too.

If they do, the remote control is ready to use.

If they don’t, you are probably using an incorrect code destined for a very similar device; at this point ignore the

SMS list and consult the SETTING CODES USING A MANUAL CODE section to ﬁnd a more suitable code.

SETTING CODES USING A CELL PHONE

NOTE: If you don’t receive an SMS on your cell phone or if the message says ERROR / NO CODE, it means the

system has not been able to process the data you have sent; Do not try sending another SMS use the MANUAL

SEARCH instead.

(only to be performed if you know the speciﬁc code to be set)

ENTERING THE CODE DIRECTLY

Three long ﬂashes indicate a correct setting. If they do not appear, repeat the procedure.

1. Hold down the selection button corresponding to the device whose code you want to enter (e.g.: ) until the indicator

light starts to ﬂash.

2. When the indicator light starts ﬂashing, release the button and immediately enter the speciﬁc code previously found (e.g.:

1306).

1. Switch on the device to be programmed: if TV, SAT, TER select a programme - if DVD insert a DVD, for videotape recorders

insert a cassette

2. Hold down the selection button corresponding to the device whose code you want to ﬁnd (e.g.: ) until the indicator

light starts to ﬂash.

3. Now release the button and brieﬂy press the button or for a DVD, VCR and PVR.

4. The indicator light ﬂashes faster; the remote control is ready for the search.

5. Point the remote control at the device. Slowly press and release the or button several times, stopping when the

device responds correctly to the command sent (you may need to press the button several dozen times).

6. When the device responds correctly, press the button. Three long ﬂashes indicate that the operation was completed

correctly.

Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code found

is incorrect, but is used for a very similar device. In that case, repeat the procedure from point 2.

If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN USE procedure

and make a note of it inside the battery cover.

NOTE: During the search the indicator stops ﬂashing and the remote control exits the programming mode in the fol-

lowing cases:

• if for 12 seconds the button indicated is not pressed or if another button is pressed

• if the list of codes to ﬁnd is terminated. If this happens, go to the www.meliconi.com website

DISPLAY CODE IN USE

If you set up the remote control using the MANUAL SEARCH procedure, obtain and make a note of the code in use as follows:

1. Hold down the selection button corresponding to the device whose code you want to ﬁnd (e.g.: ) until the indicator

light starts to ﬂash.

2. When the indicator light starts ﬂashing, release the button and brieﬂy press the button.

3. After a pause of several seconds, the indicator light produces four sets of ﬂashes, spaced out, corresponding to the code to

be obtained. Count the number of ﬂashes. Each set of ﬂashes corresponds to one ﬁgure in the code. Ten ﬂashes correspond

to the ﬁgure 0.

(only to be performed if the speciﬁc code could not be found)

SETTING CODES USING A MANUAL SEARCH

The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the product must be collected

separately from other waste. Therefore, at the end of the device’s life, you must take it to appropriate centres for the differentiated collection of electrical and

electronic waste, or return it to the retailer when purchasing a new device of equivalent type, on a one-for-one basis. Suitable differentiated collection to allow

subsequent recycling of the decommissioned device, with environmentally-compatible treatment and disposal, help to prevent any negative effects on the

environment and health and to promote the recycling of the materials of which the device is made.

Purchase date

Retailer stamp

Remote control model: Fully 8 RC

PROBLEM

The device does not respond and the indicator light does

not come on when a button is pressed.

The device does not respond but the indicator light comes

on.

When you press a button the indicator light ﬂashes and the

device does not respond to commands.

The remote control does not execute all commands

correctly.

SOLUTION

Make sure that the batteries are inserted correctly, or sub-

stitute them with 2 new 1.5V alkaline AAA/LR03 batteries.

Make sure that the batteries are new and that the remo-

te control is pointing at the device without any obstacles

between them.

If necessary, enter the remote control code again by repea-

ting the programming procedure.

Substitute the batteries, which are about to go ﬂat.

You may be using an incorrect code.

Enter the remote control settings again by repeating the

programming procedure.

TROUBLESHOOTING

2 year WARRANTY

The warranty is voided if the product is tampered with or used improperly.

If you have any questions about the new Fully 8 RC remote control:

•carefully read this Instructions Booklet which will allow you to solve most problems.

•consult our website www.meliconi.com where you will ﬁnd the answers you need in the fastest, easiest way.

INFO-LINE

Code obtained = 1306

4. Make a note of the code obtained on the label on the inside of the battery cover. You may need it in future.

Autres manuels MELICONI Télécommande

MELICONI

MELICONI personal 4 Manuel utilisateur

MELICONI

MELICONI GumBody DIGITAL 2 SMART Manuel utilisateur

MELICONI

MELICONI TLC01 Manuel utilisateur

MELICONI

MELICONI TLC04 Manuel utilisateur

MELICONI

MELICONI GumBody Universal 5 web Manuel utilisateur

MELICONI

MELICONI SPEEDY 210 STB Manuel utilisateur

MELICONI

MELICONI TLC02 Manuel utilisateur

MELICONI

MELICONI Colibri 2 Manuel utilisateur

MELICONI

MELICONI CONTROL 2 Simple Manuel utilisateur

MELICONI

MELICONI GUMBODY FACILE 100 Manuel utilisateur

MELICONI

MELICONI TLC04 Manuel utilisateur

MELICONI

MELICONI Personal 1+ Manuel utilisateur

MELICONI

MELICONI FACILE 1 RC Manuel utilisateur

MELICONI

MELICONI GumBody Personal 1 Manuel utilisateur

MELICONI

MELICONI easytel TV+ Manuel utilisateur

MELICONI

MELICONI Universal 2 Manuel utilisateur

MELICONI

MELICONI Algo 2.1 Manuel utilisateur

MELICONI

MELICONI Pratico 2 Manuel utilisateur

MELICONI

MELICONI FACILE Manuel utilisateur

MELICONI

MELICONI Personal 3 plus Manuel d'installation et d'exploitation

MELICONI

MELICONI Easytel 2+ Manuel utilisateur

MELICONI

MELICONI easytel 2+ Manuel utilisateur

MELICONI

MELICONI Speedy 210 combo Guide d'installation

MELICONI

MELICONI SPEEDY 2 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation