11
Installation and User Instructions10 Mayku Multiplier
• Beware of crushing objects and body parts when
operating the Multiplier.
• Do not attempt to insert body parts or any living
things inside the Multiplier.
• Always place the Multiplier on a stable, at, heat-
resistant surface that is suitable for the required load
during use.
• Do not use the Multiplier if the plug, the mains cord
or the machine itself shows physical damage, or
if the machine functions abnormally in any way,
or if the machine has been dropped or has been
exposed to water or other liquid.
• Do not let the Multiplier mains cord come into
contact with the heater in the top of the machine
when the heater is switched on or cooling down.
• Do not move or lift the Multiplier while it is operating
or while it is connected to an electrical socket.
• Do not move the Multiplier until it is completely cool.
• Do not leave the Multiplier unattended when in use.
• The Multiplier is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instructions concerning use of the
appliance by a person responsible for their safety.
• The Multiplier can be used by children aged
from 12 years and above if they have been given
supervision or instruction concerning use of the
appliance and understand the hazards involved
and are accompanied by a responsible adult.
• Do not allow children to interact with the Multiplier
unattended.
• Always maintain your Multiplier correctly by
following the instructions in section 6 or on-screen
when indicated by the machine.
• Keep the Multiplier and its mains cord out of reach
of animals and children less than 12 years old when
the machine is switched on or cooling down.
• Children under 12 should not use the Multiplier
under any circumstance.
• Do not use the Multiplier under the inuence of any
intoxicating substances.
WARNING
• Do not use the Multiplier outdoors or in busy public
areas.
• Objects placed on the Multiplier bed may get hot.
• Regularly check the Multiplier power cord carefully
for damage.
• Fully unwind the Multiplier mains cord before you
plug it in the wall socket.
• Do not allow the Multiplier power cord to hang over
sharp table edges or come into contact with hot
surfaces.
• Make sure that the Multiplier is switched off and
remove the plug from the mains electrical supply
when it is not in use, before it is cleaned and while it
is being repaired.
• Do not pull on the Multiplier power cord at any time.
• Do not use non-certied Mayku sheets and
materials with your Multiplier. Mayku will not be
responsible for any damage, injury or malfunction
caused by use of third party materials.
• Mayku are not responsible for the use of any
experimental and potentially damaging materials
used as sheets or templates in the Multiplier.
• Keep your Multiplier clean by wiping down with a
damp, non-abrasive cloth.
• Ensure your Multiplier is regularly maintained as per
the guidance in section 6 to ensure safe operation.
• If handing the Multiplier over to a third party, ensure
that this safety instruction manual is supplied with
the product.
CAUTION
3.1. Graphical symbols
3.1.1. Explanation of safety information on the
product and packaging
CAUTION
3.2. Potential health consequences
The Multiplier should be operated indoors only.
The area shall be well ventilated, as some plastics
used may off-gas during the heating process, and a
build-up of these fumes may be harmful.
3.3. Personal protective equipment
Always use appropriate personal protective equipment
when working with the Multiplier:
• Heat resistant gloves (category 2) - when removing
hot molds or sheets
• Hearing protection - for tank venting during
maintenance
3.4. Simplied declaration of conformity
Hereby, Mayku Ltd declares that the radio equipment
type Mayku Multiplier MMUA22100AA is in compliance
with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following
internet address: compliance.mayku.me
3.5. FCC compliance statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device shall accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
NOTICE
Symbol Meaning
CE Marking
UKCA Marking
FCC Marking
RCM Marking
Warning, risk of crushing ngers
Warning, hot surface
Warning, possibility of electric shock
