Maxview MXL060 Roam 5G Instructions de montage

Installation & User Instructions

MXL060

UK contact:

Helpline: +44 (0)1553 811000

Email: suppor[email protected]o.uk

Web: www.maxview.co.uk

Maxview reserve the right to change specifications without prior notice

9111446 Iss 2

Roam 5G

We have partnered up with one of the largest

suppliers of Wi-Fi products worldwide.

Maxview Roam 5G Powered by

This manual provides information on how to control the Roam 5G Router using your

devices internet browser. Most of these functions can be completed easier and faster

using the Maxview Roam App. See the Roam App instruction manual for more

information.

Maxview Address:

Maxview Ltd, Garage Lane, Setchey, King’s Lynn, Norfolk. PE33 0AT. UK

Contents

Record your Purchase

Please fill in the details below once purchased. This information will be required in the unlikely event of a fault

occurring with this system.

SERIAL NUMBER

2. Record your Purchase

3. Product Contents

3. Tools Required

3. Choosing a Service Provider

4. Accessories

Installation Instructions

6. Positioning your Roam

6. Important Antenna Installation Information

7. Fitting the Antenna

9. Inserting Sim Card

10. Router Installation

Router - Getting Connected and Basic Functions

12. Get to know your Router

13. Getting Online

15. Factory Reset

Router - Advanced Functions and Changing Router

Settings

17. Connecting to the Web User Interface

19. Logging out of the Web User Interface

Router - Changing the Primary Internet Source

from 3G/4G/5G to Wi-Fi

21. Changing the Primary Source

24. Changing the Routers LAN IP Address

Router - Other Functions

26. Managing and Removing Wi-Fi Connections

26. Changing Wi-Fi SSID (name) and Password

28. Entering SIM PIN

29. Controlling Data Usage & Other Functions

30. Router Firmware Update

Additional Information

31. General Safety Warnings

31. Terms and Conditions

31. Maintenance

32. 2 Year Guarantee

33. Troubleshooting & FAQ’s

37. Certification and Environment

38. Specifications

Introduction

Thank you for purchasing this product, should you have any difficulty using your

Roam 5G Mobile 3G/4G/5G Wi-Fi System please contact our friendly Customer Helpline

on +44 (0)1553 811000 or email support@maxview.co.uk.

SSID

PASSWORD

See page 12 to see where you can find this information.

Product Contents

A. Omni-directional Roof Mount Antenna

and 0.8m cables with SMA connectors*

B. 3G/4G/5G Wi-Fi Router

C. 12V Vehicle Power Supply

D. Router Mounting Bracket and Fixing Kit

E. 1.5m Ethernet Cable

*White or Grey Plastics

Tools required

- Power Drill

- 2.5mm Drill Bit

Choosing a Service Provider

To use the Maxview Roam 5G, you will need a suitable data SIM card (sold separately)

The Maxview Roam 5G is unlocked, so you can use any service provider.

The best package will depend on many factors such as data usage, budget, location of travel and

usage habits, however pre-paid data plans are usually more cost effective.

- Hack Saw

- File/Emery Paper

- Surface Cleaner

- 25mm Hole Saw

- Cross Head Screwdriver

F. 2 x Internal Wi-Fi Antennas

G. SIM Adaptor Pack

H. Roof Clamp

I. Fixing Template

J. No. 6 Screws X 3

K. No. 6 Countersunk Screws x 4

Roam Bracket Fixing Kit - For roof mounting

The raiser bracket allows you the flexibility to

mount your antenna anywhere on your roof and

enter the cable at your preferred point using the

supplied cable entry cover. Alternatively you may

have an existing cable entry point you may like to

utilise instead.

Designed and manufactured specifically for the

Roam Antenna, the aluminium bracket is

lightweight, strong and finished with a durable

white powder coating.

Suitable for any flat roof the kit also includes 3m

extension cables for flexible mounting position.

MXL050/KIT1 White

MXL050/GKIT1 Grey

Roam Extension Cables*

Extension cables can be purchased separately to

allow a flexible mounting position to the router.

*For use with this 4x4 antenna you will need to

order 2 packs.

1 metre MXL050/EXT1

2 metres MXL050/EXT2

Accessories -

Sold separately

Roam 230V PSU

230V ac to 12V dc Power Supply Unit

to power a Roam. For indoor use only.

MXL051/PSUUK

Weatherproof Socket with SMA Connectors

The Weatherproof Socket provides an external entry

point into the side of any vehicle. Available with 2

SMA connections, making it ideal when using the

Roam Antenna with the Roam Bracket Fixing Kit

(See left) to allow for a temporary connection or

where entry into the roof is not possible.

It can also be used for other applications where an

external SMA connection is required. Please note

you will require 2 Weatherproof Sockets.

B2016

3 metres MXL050/EXT3

5 metres MXL050/EXT5

Installation Instructions

Positioning your Roam 5G

Distance between Router and Antenna

For best performance, we recommend mounting the

router in close proximity to the roof mounted

antenna. For best performance, only use the antennas

standard 0.8m coaxial cables.

This means, once you have a suitable location for the

router inside the vehicle, you must also ensure there

is a suitable space on the roof to position the antenna

in close proximity to the router. For example, if you

would like to position your router in an overhead

cupboard, we recommend mounting the antenna

directly above the cupboard space.

Roof Antenna Position

We recommend leaving 30cm gap from obstacles

around the antenna to avoid interference issues

and mounting on a horizontal flat roof.*

Router Wi-Fi Antenna Space (Ref page 10)

The internal router can be mounted in a horizontal or

vertical orientation. However, bear in mind that the

Wi-Fi antenna must be vertical for maximum

performance. You must leave enough space for this.

Power Supply

The router comes with 12V cigarette adaptor.

You should ensure your router power supply can

reach your preferred power source.

1. The 3M seal provides a permanent installation.

The adhesive is extremely strong and the antenna is

not designed to be removed. Please ensure you are

completely happy with your antenna’s position and

orientation before installation.

2. The Roam 5G antenna is designed to be mounted

directly to a horizontal, flat and smooth surface such

as GRP (Glass Reinforced Plastic) with the coaxial

cables passing directly through the roof underneath

the centre of the antenna. The standard installation is

designed for roof thicknesses from 10mm up to 50mm.

If this does not suit your installation, please see our

mounting accessories (page 4) for a more suitable

mounting option.

Important Antenna Installation Information

10 - 50mm

*Sloped Roof

(Pop Top/Campers)

Although we always recommend a flat

installation to maximise Antenna performance.

In some installations you may find that you

need to install your Roam 5G on an incline.

This is useful for an Elevated Roof (Pop Top)

installation where you may use your Roam 5G

with both the Roof flat and at an incline.

We highly recommend that when installing the

Antenna on any incline you test the Roam 5G

before installation in a horizontal position and

again in the incline position to satisfy yourself of

the performance.

Fitting the Antenna

These instructions are for the standard through-the-roof installation as supplied.

1. Once you have a suitable position for the antenna,

cut out the supplied template. Use to mark the 25mm

centre hole position and mark the outside of the

antenna.

2. At the marked centre position, drill a 2.5mm pilot

hole through the roof. Use a 25mm hole saw to drill

out the centre hole through the roof.

Tidy up the hole to remove swarf and sharp edges.

3. Use the Antenna clamp to gauge the depth of the

roof. The best way to do this is to sit the Antenna

clamp upside down through the hole. Then, from the

inside, mark on the clamp where the clamp passes

through the ceiling and into the vehicle.

4. Remove the clamp and cut the clamp shaft to the

correct length. The correct length for your installation

will be the roof depth minus 3mm. This will ensure

the clamp does not bottom out on the antenna when

tightened.

E.g. If roof depth is 30mm. The clamp shaft should be

cut 27mm along the shaft.

B. Roof line

A. Cut line

A B

5. Clean the surface where the antenna will be

installed, ensuring it is free from debris and grease.

6. Pass the cables through the hole and remove the

self-adhesive backing from the 3M seal. Pass the

cables through the roof and position the antenna with

the embossed arrow facing the front of the vehicle

and the outside edge of the antenna aligning with the

marks added earlier.

IMPORTANT - Ensure the position of the

antenna is central to your markings,

as once stuck down, the antenna is not

designed to be removed.

7. Press firmly around the edges of the antenna to

ensure a watertight seal has been achieved.

8. From the inside of the vehicle, attach the clamp

and turn clockwise onto the thread protruding from

the bottom of the antenna. Continue to turn until

the clamp is compressing the seal underneath the

antenna.

9. Once in position, use 1 x No.6 Screw to secure the

clamp in position.

Front of

vehicle

Front of

vehicle

1. Remove the supplied Pin located at the bottom of

the router.

Please note your Pin maybe located in the included

SIM Card Adaptor Pack instead.

Inserting Sim Card

3. Remove the SIM tray and lay the standard size SIM card flat with the metal chip face facing up. Ensure it is in

the correct orientation and sitting completely flat in the holder.

You can convert a Micro or Nano SIM Card to the standard size using the SIM Card Adaptor Kit included.

4. Insert the SIM tray back into the router. The metal

chip should still be facing upwards and the SIM text

on the front of the tray should be the correct way up.

The tray should push into the slot without resistance,

until it is fully inserted.

The SIM is now inserted.

✓ ✓✶✓✶

Nano

Micro

Standard

Slot

2. Use this pin to firmly press on SIM eject button.

This is located next to the SIM slot. It is not necessary

to apply force to the SIM tray itself. This may damage

the router.

✶

5. Connect the 12V power lead or the 230V PSU

(available to order separately) and route the lead to

your power source.

4. Place the router into the mounting bracket.

The router can be removed from the bracket at any

time to change the SIM card as required.

2. Attach the antenna coaxial cables to the top 4

connectors. These are marked ‘mobile’. Note the order

of the cables does not matter.

IMPORTANT - To prevent damage take

care to ensure the centre pins are

aligned before attaching the connector.

1. Position Router Bracket and mark hole positions.

Depending on material, drill a pilot hole or use a

bradawl. Mount the Router Bracket to the surface

using the 4 x No.6 Screws provided.

Note: Make sure the ‘Maxview Logo’ is

horizontal and in the correct orientation.

IMPORTANT - Ensure the router is not mounted

too close to other electrical devices, as this may

prevent it from working or negatively impact

performance.

Router Installation

The optimum positioning for the Wi-Fi antennas on

the Roam 5G Router is pointing directly upwards.

However, the unit can be fitted with the antenna at a

45° or 90° angle, or pointing downwards or forwards.

This may have a small detrimental effect on the

signal strength, which will become more significant

at greater distances from the router. However, for

leisure vehicle applications, this will likely only cause

a negligible drop in performance.

3. Attach the Wi-Fi antennas to the bottom

connectors. These are marked ‘Wi-FI’. These should be

positioned so they are vertical.

6. The installation is now complete. You may

wish to tidy up cable routing to suit your installation.

Table des matières

Autres manuels Maxview Antenne

Maxview

Maxview Roam X Campervan Instructions de montage

Maxview

Maxview CRANK UP B2590/50SNZ Manuel

Maxview

Maxview Connect Sky Q MXL028 Manuel du propriétaire

Maxview

Maxview MXL028/65NZ Manuel utilisateur

Maxview

Maxview Target MXL017/65 Manuel

Maxview

Maxview OMNIMAX Instructions de montage

Maxview

Maxview COMBO/50 Instructions de montage

Maxview

Maxview Precision Waterways MXL024/55 Manuel

Maxview

Maxview MXR0010 Manuel utilisateur

Maxview

Maxview MXR0052 Manuel utilisateur

Maxview

Maxview Gazelle Pro Manuel utilisateur

Maxview

Maxview MXL050 Roam Instructions de montage

Maxview

Maxview Precision I.D MXL019/55 Manuel utilisateur

Maxview

Maxview MXL012/75TWINAU Manuel utilisateur

Maxview

Maxview GAZELLE Fiche d'information produit

Maxview

Maxview Omnimax Instructions de montage

Maxview

Maxview ANTMINI Manuel utilisateur

Maxview

Maxview MNISAT MXL001 Instructions de montage

Maxview

Maxview MXR0024 Manuel utilisateur

Maxview

Maxview MXL028 Manuel du propriétaire

Maxview

Maxview MXL002 Manuel utilisateur

Maxview

Maxview Precision I.D MXL019/55 Instructions de fonctionnement

Maxview

Maxview MXL041 Manuel utilisateur

Maxview

Maxview VuQube II Q Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

CommScope

CommScope CMAX-OMFX-43M-I53 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur