7
Customer
Support
1.800.897.9755 x1 suppor[email protected]MM700 Installation Instructions 6
If the lower VESA holes are less than 3" from the
bottom of the TV:
Connect the Vertical
Braces {31} through
the UPPER VESA
holes only, so that
the bottom of the
braces are between
3" to 10" from the
bottom of the TV. *
If the only option is
to attach the Vertical
Braces to the Upper
Vesa holes through a
slot: 1) Hand-thread
the screw through
the slot; 2) slide the
Vertical Brace upward
until the screw meets
the bottom of the
slot; and 3) tighten
the screw.
You must attach the
Brace Extenders {30}
to the Vertical Braces
as described in STEP
1.7. However, you
must also attach the
LOWER VESA hole
through the Brace
Extender as shown.
SIDE VIEW
{31}
{55}
{15}
{15}
{30}
{31}
{31}
{30}
Attach Brace Extenders to the Vertical Braces.
Slide the Brace Extenders {30} (with the Horizontal Brace
{55} now attached to them) onto the Vertical Braces {31}.
Position it so that the Horizontal Brace will be hidden by
the TV. Use Screws {18} and Nuts {23} to attach.
Attach the Horizontal Brace to Brace Extenders.
Slide one Brace Extender {30} onto the left end of the
Horizontal Brace {55}, then slide the other Brace Extender
onto the opposite right end.
Attach the Vertical Braces to the back of TV.
Install the Vertical Braces {31} so that the bottoms of the
braces are between 3" to 10" from the bottom of TV,
(*or Soundbar if one is installed) centering the braces
vertically as much as possible.
{31}
3 to 10
INCHES *
SIDE VIEW
{31}
{31}
VERTICAL BRACES MUST ALWAYS
BE INSTALLED HIGHER THAN THE
BOTTOM OF THE TV.
If the lower VESA holes are less than
3" from the bottom of the TV, go to
STEP 1.6; otherwise skip to STEP 1.7.
Hand-thread screw combination into the TV.
Ensure there is adequate thread engagement
without hitting the bottom of threaded insert.
Do not use screws that
are too long for the TV’s
threaded inserts because
it may damage internal
components!
MUST LEAVE
A GAP IN
THREADED
TV INSERT
MAXIMIZE THREAD
ENGAGEMENT FOR
STABILITY
AFTER ASSEMBLY
(ENLARGED)
{10}
{12}
CAUTIONCAUTION
TV SCREW
UPPER
VESA
HOLE
WITH
SCREW
IN PLACE
LOWER
VESA
HOLE
WITH
SCREW
IN PLACE
{15}
{15}
Attach Heat-Sensing Center Handle to the
Horizontal Brace.
Attach the Center Handle {53} with Screws {15} to the
Horizontal Brace {55}, ensuring that the Handle is within
one inch from the bottom of the TV or sound bar.
{55}
INSTALL THE CENTER
HANDLE SO THAT IT
SITS 1" BELOW THE
TV OR SOUND BAR
IF USING ONE.
{53}
1" MAX
(25mm)
SIDE
VIEW
If installing a sound bar, attach the Sound Bar Wings.
Use Screws {15} and Nuts {23} to attach the Sound Bar
Wings {16} to the Horizontal Brace {55}. Position the
Wings to t the mounting holes of the sound bar.
Install sound bar. See below for Sound Bar Wing
installation information.
{16}
{16}
{55}
{23}
{23} {23}
{31}
{31}
{30}
{30}
{55}
{18}
{18}
Align the Brace Extenders with the Vertical Braces
(that are already mounted to the back of the TV) while
positioning the Horizontal Brace so that it extends an
equal amount on either side of the Brace Extenders.
Attach Horizontal Brace to Brace Extenders w/Screws {15}.
{30}
{55} {55}
{30}
Protect the TV with Heat-Sensing Center Handle.
The patented Heat-Sensing Handle turns red if the
temperature above the replace exceeds a safe 110° F –
a visual cue that either the TV needs to be raised to the
UP position or the replace needs to be turned o.
To eectively lower the TV using the Handle, follow the
MantelMount Three-Step Pull Down Technique:
1. Stand in front of the mount, arms extended with
palms up and elbows straight.
2. Firmly grasp the lifting handles and lean back
slightly with one foot forward and one foot back.
3. Step backward with forward foot to pull the mount
away from the wall while placing downward
pressure on the handles (keep elbows extended).
Arrange Sound Bar Wings and sound bar to work with
the Heat-Sensing Center Handle.
The Sound Bar Wings may be positioned and rotated so
that the Center Handle {53} will reach below the sound
bar.
For example, if a sound bar is tall, the Brace Extenders
{30} and Horizontal Brace can be attached lower down on
the Vertical Braces toward the bottom of the sound bar
while the Wings point upwards in order to align with the
sound bar’s installation holes.
{53}
TALLER SOUND BAR
WIDER SOUND BAR
OPTIONAL
*
If installing this mount with a MantelMount RB100 Recess Box,
the bottom of the Vertical Brace must be 6”-10” from the bottom of
TV (or 6” from the bottom of the Soundbar if one is installed).
*
If installing this mount with a MantelMount RB100 Recess Box,
the bottom of the Vertical Brace must be 6”-10” from the bottom of
TV (or 6” from the bottom of the Soundbar if one is installed)..
1.4
OPTIONAL
1.6
1.5 1.8 1.9
1.10
1.7
{30}
