M-system 10VS4 Manuel utilisateur

BEFORE USE ....

Thank you for choosing us. Before use, please check con-

tents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact our sales ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

Mounting screw (M3.5 × 10)...............................................(2)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%,

approx. 60mA with voltage output 1/3

approx. 110mA with current output 1/3

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Be sure to put the terminal cover on while the power is

supplied.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Zero Adj.

Span Adj.

Body

Specifications

Connection Diagram

(cover side)

Terminal Cover

INSTALLATION

Use Standard Rack (model: 10BXx).

4-OUTPUT ISOLATOR MODEL 10VS4

EM-0886 Rev.5 P. 1 / 2

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the terminal cover.

■EXTERNAL DIMENSIONS unit: mm (inch)

130 (5.12)

3 (.12)

51 (2.01)

82 (3.23)

2–4.3 (.17) dia.

MTG HOLE TERMINAL COVER

15–M3.5 SCREW8 (.31)

91 (3.58)

99 (3.90 )

26 (1.02)

1234

567

12 13 14 15

10 11

50 (1.97)

■CONNECTION DIAGRAM

–

INPUT OUTPUT 1

–

OUTPUT 2

–

OUTPUT 3

–

OUTPUT 4

CONNECTOR

POWER

OUTPUT 2

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage supplied to the rack

(model: 10BXx). For the DC power source, be sure that

the ripple level is within 10% p-p.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

We offer a series of lightning surge protector for protec-

tion against induced lightning surges. Please contact us to

choose appropriate models.

10VS4

EM-0886 Rev.5 P. 2 / 2

MG CO., LTD. www.mgco.jp

5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Autres manuels M-system Émetteur

M-system

M-system 10SP Manuel utilisateur

M-system

M-system 99SVA Manuel utilisateur

M-system

M-system CTS2 Manuel utilisateur

M-system

M-system Mini-M M2TG Manuel utilisateur

M-system

M-system Mini-MW Series Manuel utilisateur

M-system

M-system M5XU Manuel utilisateur

M-system

M-system M1EXS-2 Manuel utilisateur

M-system

M-system MXV Manuel utilisateur

M-system

M-system M3SMS Manuel utilisateur

M-system

M-system Mini-M M2XM2 Manuel utilisateur

M-system

M-system M5PA-CA-R Manuel utilisateur

M-system

M-system Mini-M M2E Series Manuel utilisateur

M-system

M-system W2VF Manuel utilisateur

M-system

M-system 10JRE Manuel utilisateur

M-system

M-system 10TS Manuel utilisateur

M-system

M-system 27PM Manuel utilisateur

M-system

M-system Mini-M M2DY Manuel utilisateur

M-system

M-system M3LR Manuel utilisateur

M-system

M-system M2EXV Manuel utilisateur

M-system

M-system 10VK Manuel utilisateur

M-system

M-system W5 Series Manuel utilisateur

M-system

M-system W5-UNIT Manuel utilisateur

M-system

M-system LC2 Manuel utilisateur

M-system

M-system 6AC Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur