LUX KONOz Instructions d'utilisation

Installation Settings Guide

In this guide we will describe the advanced

installation settings that you can access from

KONOz’s main menu. We recommend that

an HVAC service professional uses these settings

to fine-tune your thermostat’s performance for

your home.

You can access the installation settings by going to

the main menu and selecting the gear icon. You

will see “IS” on the screen and will be prompted to

select “yes” or “no”. Select “yes” to access the

installation settings. Rotate the knob to view

settings and press the knob to confirm.

Once in the installer settings, rotate the knob to

change a setting value. Press the knob to confirm

the new value and proceed to the next option.

There are three ways to exit the settings:

1. Continue through the remaining settings until you

pass setting 99.

2. Press and hold the knob for 3 seconds after you

confirm any changes to your settings.

3. Wait 60 seconds after you confirm any changes

to your settings.

Installation Settings Guide

System Type & Configuration

You will first see your current system type and configuration – confirm by pressing the knob

and then you will begin navigating through the available settings.

HVAC system type

F = Furnace

HP = Heat Pump Available System

Modes

HVAC system subtype

Furnace Systems

ELEC: Electric fan. Thermostat calls fan

to run with heat

GAS: Gas fan. Thermostat does not call

fan to run with heat

BOIL: Boiler. No fan connected to

heating system

Heat Pump

o: Changeover valve = O

b: Changeover valve = B

All manuals and user guides at all-guides.com

all-guides.com

-01 Temperature Format

F for Fahrenheit C for Celsius

Use this setting to select your preferred temperature format.

-02 Temperature Calibration

Installation Settings Guide

KONOz is factory calibrated, but you can use this setting to adjust the temperature

sensor for your home. The screen will alternate between your calibration temperature and the

offset value – to remove calibration, make sure that the offset value is set to 0.

-03 Available HVAC Modes

Heat Only Heat & Cool

KONOz uses terminal detection to identify your system type and you can use this

installation setting to view and change the available modes. Use this setting to view and/or

change the different modes available depending on your system type. Rotate the knob to see

various options and configurations for your system.

Cool Only

All manuals and user guides at all-guides.com

Installation Settings Guide

-04 Maximum Heat Limit

Default Temperature: 90°F

Use this setting to set a maximum temperature limit for your heating system. The limit can be

as high as 90°F (32°C) or as low as 60°F (15°C). *Note: Not available for cool only systems

-05 Minimum Heat Limit

Default Temperature: 45°F

Use this setting to set a minimum temperature limit for your heating system. The minimum

heat limit range is from 60°F (15°C) to as low as 45°F (7°C). *Note: Not available for cool

only systems

-06 Maximum Cool Limit

Default Temperature: 95°F

Use this setting to set a maximum temperature limit for your cooling system. The maximum

cool limit range is dependent on your heating limits.

All manuals and user guides at all-guides.com

Installation Settings Guide

-07 Minimum Cool Limit

Use this setting to set a minimum temperature limit for your cooling system. The minimum

cool limit range is dependent on the values you entered for your heating and cooling limits.

-08 System Type

Use this setting to modify the system type. The available options include Gas Furnace, Electric

Furnace, Boiler (No Fan) and Heat Pump. See step 09 below for additional options when

selecting Heat Pump.

-09 System Type - Heat Pump

If you selected heat pump during #8, you will then have to select your valve type in #9. Select

O or B depending on your valve type. B will energize the B/O terminal in heat mode and O

will energize the B/O terminal in cool mode.

Gas Furnace Electric Furnace Boiler (No Fan)

Heat Pump Option O Valve B Valve

Default Temperature: 50°F

All manuals and user guides at all-guides.com

Installation Settings Guide

-10 Minimum On/Off Time

-11 Temperature Swing

Use this setting to set a swing value. Your swing setting determines how far the ambient

Temperature can deviate from the set temperature before KONOz turns on your heating

or cooling system. You can select 0, .25°, .5°, 1° or 2.25°.

Use this setting to set a standby time so that your HVAC systems can safely and efficiently

switch on and off. You can either select a 5-minute or a 2-minute off time. During normal

operation, the hourglass icon indicates that the minimum off time is temporarily preventing

your heating and cooling system from turning on.

-12 Stage 2 Heating Offset (for conventional systems)

Use this setting to set a value that your thermostat will use to decide when to turn on your

second stage of heating. You can select Off, 1, 2, 3, 4 or 5 degrees F.

Off, no second stage heat 1° 5°

All manuals and user guides at all-guides.com

Installation Settings Guide

-13 Stage 2 (Auxiliary) Heating Offest (for heat pump systems)

Use this setting to set a value that your thermostat will use to decide when to turn on your

second stage of heating. You can select Off, 1, 2, 3, 4 or 5 degrees F.

-14 Clock Format

12 Hour AM/PM Display 24 Hour Time Display

Use this setting to choose between 12-hour am/pm time display or 24-hour time display.

*Note: This setting not available with battery-only power.

-15 Backlight

Use this setting to choose between a backlight auto-off setting of 10 seconds or an always-on

backlight. When the backlight is turned off the display will not be visible. Press the knob

to turn on the display. *Note: This setting not available with battery-only power.

Off, no second stage heat 1° 5°

10 Seconds Always On

All manuals and user guides at all-guides.com

all-guides.com

Installation Settings Guide

-16 Filter Life

Off 30 Days

Use this setting to turn on and set a value for your air filter’s lifespan. You’ll then be able to check

its remaining lifespan in the fan settings sub-menu. (You can select Off, 30, 60, 90, 120, 180 or 365 days).

365 Days

-98 Compressor Bypass

Use this setting to temporarily disable the minimum on/ off time protection. If you set

compressor bypass protection to ‘yes’ then your system will switch heating and cooling on/off

without waiting for the minimum on/off time.

Compressor Bypass On Compressor Bypass Off

-99 Factory Reset

Reset KONOz Do Not Reset KONOz

Use this setting to initiate a factory reset and to setup your KONOz from scratch.

All manuals and user guides at all-guides.com

Installation Settings Guide

We’re here to help! Please contact our customer support team for assistance:

PHONE:

LIVE CHAT:

EMAIL:

VIDEOS:

SUPPORT HOURS:

856.234.8803

LuxProducts.com/support

techsupport@luxproducts.com

LuxProducts.com/Videos

8am to 6pm EST, Monday - Friday

For wiring diagrams, please reference the appendix

section of the KONOz Manual

Lock: Press and hold the knob for 10 seconds on the main run screen to lock local

control of KONOz. When locked, press and hold the knob for 10 seconds

to unlock.

Power Cycle: Remove KONOz from its base and locate the black reset

button on the back of the thermostat. Press and hold this button for 3 seconds

to fully power cycle the device.

EMER Heat: If you have a Heat Pump system with stage 2 (auxiliary) heat

enabled, you can select EMER heat from the mode menu. When this is enabled,

the thermostat will not use the compressor heating stage and will use the

auxiliary heating stage as the only heat source.

-Additional Features

LUX Products - Designed in Philadelphia

All manuals and user guides at all-guides.com

Autres manuels pour KONOz

Autres manuels LUX Thermostat

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur