LUX GEO Manuel utilisateur

WiFi THERMOSTAT

Welcome to your LUX/GEO quick-start guide

Your LUX/GEO internet connected thermostat puts the control of your comfort in your hands and you

are only 10 easy steps away from completion.

Step 1: Getting started

Included:

Items needed:

IF AT ANY TIME DURING THE INSTALLATION AND SET-UP PROCESS YOU NEED ADDITIONAL SUPPORT,

VISIT LUXGEO.COM OR CALL 856.234.8803

2-AA Lithium

batteries

2 mounting

screws

2 wall

anchors

wire stripper

& cutter

Phillips & at

head screwdriver

WiFi enabled

mobile device

IF YOU DO NOT HAVE AN iOS OR ANDROID DEVICE, PLEASE VISIT LUXGEO.COM OR CONTACT LUX SUPPORT

GEO

Download App and

Create Your Account

Download your LUX Products App

Depending on device type, search

the App store for “LUX Products” and

create your LUX user account

Lux

Power Bridge

WiFi

router

For Use On:

Most 24-volt heating and cooling systems

1 or 2 stage heat / 1 or 2 stage cool: gas, oil, or electric

furnace and a/c systems

1 or 2 stage heat / 1 stage cool: heat-pump style systems

2-wire hydronic (hot water) zone valves

Gas Millivolt wall / ﬂoor heaters

Not For Use On:

120/240 VAC line-

voltage systems

(without a transformer)

Heat pumps that have

(Y2) two compressor

stages

Locate and gather the following items for ease of installation

Step 3: Determine how your LUX/GEO will be powered

LUX/GEO can be powered by one of four methods (in order of best performance):

Method #1 & #2 (Preferred): 24V System Power “C-wire” (this powers GEO from your

heating/cooling equipment and provides the best performance when using WiFi)

Method #3: USB micro-port on GEO (wall adapter & cord not included - use 1A wall adapter)

Method #4: Battery Powered* (2-AA Lithium batteries included)

YES

USE Method #1:

“C-Wire”

(refer to Step 4.1)

USE Method #2:

LUX Power Bridge

(refer to Step 4.2)

USE Method #3:

Micro-USB

(see notes on

following page)

USE Method #4:

2-Lithium Batteries

(see notes on

following page)

Do you

have home

automation

devices like

Amazon

Alexa

In your

wiring photo

from Step 2,

do you have

a “G” wire

In your

wiring photo

from Step 2,

do you have

a “C” wire

Step 2: Switch power o and take photo of existing wiring

TAKE

PHOTO OF

CURRENT

WIRING

IMPORTANT: Turn o the power at circuit

breaker to both your heating & cooling

systems before performing any wiring.

Notice for battery powered installations

GEO

should only be used with lithium batteries.

Battery failure could leave property without controlled heating or cooling. Reliance on battery

power is not recommended with prolonged absence from property.

Battery life will vary depending on your settings. After installation you can choose to adjust the

“energy proﬁle” for your GEO. This energy proﬁle will determine the delay in GEO responding to

changes from the App, but can increase battery life.

Refer to Step 4.1 for wiring method.

Notes for Method #3: Micro-USB

You can use any standard USB wall adapter and Micro-USB cable, however the wall adapter must

be rated for 1 Amp (1000 mA) or higher.

A Micro-USB kit with extra long power cable is available from LUX through our

www.luxproducts.com website.

Refer to Step 4.1 for wiring method.

Step 4: Remove existing thermostat and wire your LUX/GEO

AS AN ADDED RESOURCE, A GLOSSARY OF TERMS IS AVAILABLE ON

LUXGEO.COM, ALONG WITH VIDEO DEMOS

WIRES INSERT INTO SIDE OF

TERMINAL, UNDER SCREWS.

HOLD

AND

PULL TO

OPEN GEO

Release wires and mounting screws from old thermostat

and remove base from wall.

Open GEO from base, pull up on plastic “cover”

between terminal blocks to access and pull wires

through.

Secure GEO base to wall (mounting hardware &

optional wall plate included)

REMOVE

TERMINAL

COVER

On the following pages, there are several dierent methods

of wiring the GEO thermostat depending upon system

type and the power method selected in Step 3. Follow the

scenario most appriate for your system type, and please

contact LUX support if there are any questions.

HEAT-PUMP (COMPRESSOR) STYLE HEAT/COOL SYSTEM [typical wire color used]

R (or RC/RH) = 24(+) VAC Power, Cool [RED]

O = Reversing Valve [ORANGE]

Y1 = Heat Pump Outdoor Unit [YELLOW]

G = Blower Fan [GREEN]

W2 = Auxiliary/Emergency Heat [WHITE]

C = 24(-) VAC Common [BLUE]

B** = Reversing Valve (only if no “O” wire- [can vary per each installation]

ie: Rheem/Ruud/Bard systems)

Note: There should NOT be a wire used on the W1 wire connection at terminal.

** IMPORTANT: If you have both an O wire and B wire (ie: Trane system), please install B to the “C” terminal

4.1b Wiring Terminal Reference: Heat Pump Systems (without LUX Power Bridge)

Referencing your wiring photo, attach your thermostat wires to the LUX/GEO using your original wiring

letters and the following terminal reference as a guide based upon your system type.

GAS / OIL / ELECTRIC FURNACE and/or AIR CONDITIONING [typical wire color used]

RH (or R) = 24(+) VAC Power, Heat [RED]

W1 = 1st Stage Heat [WHITE]

G = Blower Fan [GREEN]

C = 24(-) VAC Common [BLUE]

Y1 = 1st Stage Cool [YELLOW]

(other)

RC = 24(+) VAC Power, Cool [can vary per each installation]

B = Heat Mode Damper [can vary per each installation]

O = Cool Mode Damper [can vary per each installation]

W2 = 2nd Stage Heat [can vary per each installation]

Y2 = 2nd Stage Cool [can vary per each installation]

IMPORTANT: If you have both an RC and RH wire present, remove the RED shorting cap inside of GEO

(the YELLOW shorting cap must only be on one pin, not both).

Wiring is complete - you may return “cover” between terminal blocks

Wiring for methods: #1 C-wire, #3 Micro-USB, and #4 Battery Power

4.1a Wiring Terminal Reference: Conventional Furnace - gas/oil/electric & air-

conditioning (without LUX Power Bridge)

Referencing your wiring photo & terminal guide below, wire to GEO.

IMPORTANT: For Heat Pump applications, the YELLOW shorting cap must be across both metal pins

instead of the default of just one. Also, there will NOT be a wire connected to the “W1” terminal.

Wiring is complete - you may return “cover” between terminal blocks

Wiring for method: #2 using LUX Power Bridge

4.2 Wiring Terminal Reference: Installing GEO with the LUX PowerBridge

The LUX PowerBridge is for applications that do not have a C-wire at the thermostat:

Take a photo of the wiring at both your thermostat and your furnace. The Power Bridge

cannot be used with 2-wire applications, and requires at least cooling or heating wires

and a fan “G” wire at the thermostat. If you have more wires (multi-stage systems) than

are needed for installing the Power Bridge, leave them attached as they are.

AT YOUR THERMOSTAT – Use the thermostat wire labels to identify each thermostat

wire with its current terminal letter. If any of your thermostat wiring connections are

unclear, please call LUX Technical Support.

NOTE: When using the Y-Splitter, pull the orange

lever all the way up before inserting your wire.

Press the lever back down to lock a wire in place.

AT YOUR FURNACE (AIR HANDLER) – Remove the door panel and locate your control

board. Use the additional wire labels to identify each wire from your thermostat with

its terminal letter on the control board. If any of your furnace wiring is unclear, please

call LUX Technical Support. Depending upon your application, some wires attached to

the control board will remain in place and will not be used with the LUX Power Bridge.

NOTE: When installing the Power Bridge, press the terminal levers before inserting wires into the

holes. Once the wire is fully inserted, gently pull on the wire to conﬁrm that it is securely installed.

Press all the way down on the lever to release a wire.

4.3a Installing the LUX Power Bridge on Conventional Systems

Current Wiring:

After Set Up:

If your system provides a second stage of heating, you may have a W2 wire. You can leave this wire as-is in your

furnace and connect it to the W2 block on your new thermostat.

If you have two R wires (R, Rc, or Rh), please call LUX Technical Support for assistance with your installation.

Connect your old Y wire to the empty hole next to the blue end of the y-splitter (1). Snap the orange lever shut to

secure the wire in its place. Insert the yellow end of the y-splitter into the thermostat’s Y terminal and the green wire

into the G terminal.

Move your old G wire to the C terminal on your thermostat.

Thermostat

Furnace

O/B

BO/

Power Bridge

O/B

(1)

BO/

4.3b Installing the LUX Power Bridge on Heat Pump Systems

Current Wiring:

After Set Up:

If your system provides a second stage of heating, you may have a W2 wire. You can leave this wire as-is in your furnace and

connect it to the W2 block on your new thermostat.

You may or may not have a W1 terminal block on your control board. Do not connect the Power Bridge’s “W” wire to any

terminal block on your control board.

Connect your old Y wire to the empty hole next to the blue end of the y-splitter (1). Snap the orange lever shut to secure the

wire in its place. Insert the yellow end of the y-splitter into the thermostat’s Y terminal and the green wire into the G terminal.

Move your old G wire to the C terminal on your thermostat.

Power Bridge

O/B

(1)

BO/

Thermostat

Air Handler

O/B

BO/

4.3c Installing the LUX Power Bridge on Cool Only Systems

Current Wiring:

After Set Up:

The Power Bridge’s “W” wire is not used for this system - do not connect it to your control board.

Connect your old Y wire to the empty hole next to the blue end of the y-splitter (1). Snap the orange lever shut to

secure the wire in its place. Insert the yellow end of the y-splitter into the thermostat’s Y terminal and the green wire

into the G terminal.

Move your old G wire to the C terminal on your thermostat.

Power Bridge

O/B

(1)

BO/

Thermostat

Air Handler

O/B

BO/

4.3d Installing the LUX Power Bridge on Heat Only Systems

Current Wiring:

After Set Up:

For this system type, you will need to connect the Power Bridge’s “Y” wire to the W1 terminal block on your control

board. Re-label the yellow tab on the Power Bridge’s Y wire with one of the included W wire stickers. You will not

use the Power Bridge’s “W” wire for this system.

Connect your old W wire to the empty hole next to the blue end of the y-splitter (1). Snap the orange lever shut to

secure the wire in its place. Insert the yellow end of the y-splitter into the thermostat’s W terminal and the green wire

into the G terminal.

Move your old G wire to the C terminal on your thermostat.

Thermostat

Furnace

Power Bridge

O/B

(1)

BO/

O/B

BO/

Step 8: Connecting LUX/GEO

You will need an iOS or Android device to set up your

GEO

. If you have a dierent

device, visit

LUXGEO.com. Set-up follows a series of screen prompts – have your GEO

and mobile device ready.

8a. Getting ready to connect

You’ve downloaded the LUX

Products App, created a

user account and now,

from your GEO, select

“yes” for WiFi setup

GEO will begin scanning –

but you can move on to 8b.

Step 7: If you have not yet downloaded your LUX Products App, do so now

Step 5: Power on

For methods #1 with C-wire and #2 with LUX

Power Bridge: secure GEO front onto base

For method #4 Battery Power: insert 2-AA

Lithium batteries & secure GEO front onto

base

For method #3 USB power:

place a ﬂathead screwdriver

against port cover from inside

GEO along bottom side – twist

& push out. Plug in Micro USB

and insert into base.

Once GEO front has been

secured to base (line up and

ﬁrmly push), return power to

system.

Step 6: Conﬁgure system settings

GEO will guide you through setup

Rotate the control wheel to navigate

through options and values. To make a

selection, press ; to go back, press .

GEO will prompt you to select:

1. Whether heating and/or cooling are

connected.

2. System type (only applies if you have heat).

Note if you wired per section 4.1a or 4.3a you

have a furnace. If you wired per section

4.1b or 4.3b you have a heat pump.

If furnace fan is not operating properly after

installation, change from furnace:gas to

furnace:electric in the settings menu.

3. The number of stages for heat/cool you have.

Most common is 1 heat/1 cool. Not sure? refer

to our online glossary to learn more.

4. If you have set more than 1 stage of heat or cool,

the OFFSET setting adjusts the stage-2 cut in.

INSERT

SCREWDRIVER

& TWIST TO POP

OUT USB COVER

---

WITH GEO SECURE &

POWER ON – THE DISPLAY

SHOULD ILLUMINATE, IF

NOT, CHECK POWER IS

BACK ON.

Table des matières

Autres manuels LUX Thermostat

LUX

LUX TX500E Manuel utilisateur

LUX

LUX ELV1/PSPLV510 Manuel utilisateur

LUX

LUX ELV4d Manuel utilisateur

LUX

LUX TX100E Manuel utilisateur

LUX

LUX TX9100Ua SMART TEMP Manuel utilisateur

LUX

LUX DMH110b Manuel utilisateur

LUX

LUX DMH105 Manuel utilisateur

LUX

LUX TX9600TS Manuel utilisateur

LUX

LUX KONOz Instructions d'utilisation

LUX

LUX T40-1143 Manuel utilisateur

LUX

LUX SMART TEMP TX500b Series Manuel utilisateur

LUX

LUX TX1500E Manuel utilisateur

LUX

LUX CS1 Manuel utilisateur

LUX

LUX TX500E Manuel utilisateur

LUX

LUX 105/2110 Series Manuel utilisateur

LUX

LUX KONOzw Manuel utilisateur

LUX

LUX TX700U Manuel utilisateur

LUX

LUX TX9600TS Manuel utilisateur

LUX

LUX DMH110b Manuel utilisateur

LUX

LUX T20-1141SA Manuel utilisateur

LUX

LUX TX1500B SERIES Manuel utilisateur

LUX

LUX PSP511Ca Manuel utilisateur

LUX

LUX DMH110b Manuel utilisateur

LUX

LUX TX100Ea Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur