Lucent Technologies Cajun P333T Manuel utilisateur

Cajun P333T

Quick Start Guide

1. Unpack

2. Rack mount

3. Power up

4. Connect the cab es

5. Configure

6. Run Web-based Manager (optiona )

1. Unpack

Check the package contents for

the fo owing

• Cajun P333T Workgroup Switch

• Cajun P333T Quick Start Guide (this

document)

• Cajun P333T Re ease Notes

• Cajun P330 Documentation and Uti ities

• AC power cab e

• RJ-45 to DB-9 seria adapter cab e

• Four rubber feet

• Four screws with washers for rack

mounting

LEthernet connection cables are not

supplied

2. Rack mount

1. Snap open the ends of the front pane to

revea the screw ho es.

2. Position the unit in the rack.

3. Secure the unit to the rack, taking care

not to overtighten the screws.

4. Snap c osed the hinged ends of the front

pane .

:You can now safe y connect cab es to the

device.

WARNING: Disconnect a cab es from the switch before

proceeding with the rack insta ation.

Rack Mounting

3. Power up

Cajun P333T AC Version

1. Insert the power cord into the appropri-

ate power in et (BUPS or Power Supp y)

in the back of the unit

2. Insert the other end of the power cord

into the e ectricity supp y or the BUPS

connector.

:The unit powers up and performs a se f

test procedure.

Cajun P333T DC Version

WARNING: Before performing

any of the fo owing

procedures, ensure that DC

power is OFF.

CAUTION: This product is intended for

insta ation in restricted access areas and is

approved for use with 18 AWG copper con-

ductors on y. The insta ation must comp y

with a app icab e codes.

1. Connect the power cab e to the switch at

the input termina b ock.

LThe terminals are marked “+”, “-“ and

the IEC 5019a round symbol.

LThe size of the three screws in the terminal

block is M3.5.

LThe pitch between each screw is 9.5mm.

2. Attach the appropriate ugs at the wire

end of the power supp y cord.

3. Wire the DC power supp y to the termi-

na b ock.

:The unit powers up and performs a se f

test procedure.

WARNING: The proper wiring

sequence is:

• ground to ground

• positive to positive ( ine to L)

• negative to negative

(neutra to N).

The ground wire shou d a ways

be connected first and discon-

nected ast.

Power Supply

Connector

BUPS

Connector

Cable to

Upper Unit

Cable to

Lower Unit

AC Input

Cajun 333T Rear Connectors (AC version)

Power Supply

Connector

BUPS

Connector

Cable to

Upper Unit

Cable to

Lower Unit

DC Input

Cajun 333T Rear Connectors (DC version)

12345678910 11 12

13 14 15 16 17 18 19 20 21 22 23 24

FC Hspd LAG PWR

OPR

SYS

LNK COL Tx FDXRx

FIV

Function LEDs

Port LEDs

Left/Right

and Reset (both)

Switches

FIV Switch

EXPANSION

SLOT

51 52 53 54 55 56 57 58

59 60 61 62 63 64 65 66

FIV – Force Initia Version (see Cajun P333T

User’s Guide)

PWR – Shows when power is on

OPR – Shows CPU boot status

SYS – Shows system status

LNK – When ON, ink is OK

COL – When ON, indicates a co ision on

the port in HDX mode

Tx, Rx – Shows traffic activity for

transmitted and received packets

FDX – Shows Fu /Ha f Dup ex mode

FC – When ON, F ow Contro is enab ed for

a port in FDX mode

Hspd – Shows speed of port (10 Mbps or

100/1000 Mbps)

LAG – When ON, the port is inc uded in a

Link Aggregation Group (LAG).

4. Connect the cab es

Connect PCs, servers, routers,

workstations, and hubs

1. Connect the appropriate Ethernet con-

nection cab e (not supp ied) to a 10/100

Mbps port on the front pane of the

Cajun P333T.

LYou should use standard RJ-45

connections. You must use CAT-5 cable for

100 Mbps operation.

2. Connect the other end of the cab e to the

Ethernet port of the PC, server, router,

workstation, switch or hub.

LYou should use a cross cable when

connecting the Cajun P333T to a switch or

hub

3. Check that the appropriate ink (LNK)

LEDs ight up.

Connect the conso e cab e

1. Connect the supp ied specia RJ-45 con-

nector to the port marked “Conso e” on

the front pane of the Cajun P333T.

2. Connect the other end of the cab e to a

termina or PC with termina emu ation

software insta ed.

3. Configure the seria port settings of the

PC as fo ows:

• 9600 Baud

• No parity

• 8 data bits

• 1 stop bit

• No f ow contro

Cajun P333T LEDs

5. Basic configuration

To connect a PC termina or

VT-100 termina to the Cajun

P333T

LThis section presumes that you have made

the connection to the console port as

described in section 4.

1. If you are using a PC, initiate a

VT-100 termina emu ation session using

an app ication such as Windows®

HyperTermina .

2. Press Enter

:The Welcome to Cajun P330 menu

is disp ayed.

3. Enter the User name root when

prompted.

4. Enter the User Leve password root

when prompted.

:The prompt Cajun_P330-N> appears

LNis the number of the switch in the stack.

5. Enter enable to enter the Privi eged

eve .

6. At the Cajun_P330-N# prompt, type:

set interface <inband> <vlan>

<ip_address> <netmask>

7. Rep ace <v an>, <ip_address> and <net-

mask> with the VLAN, IP address and

net mask of the stack.

8. Press Enter to save the IP address and net

mask.

9. Enter reset and press Enter to reset the

stack at the Cajun_P330-N# prompt

10. After the Reset, perform ogin to

Privi eged eve again as described above.

11. At the Cajun_P330-N> prompt, enter

set ip route <dest><gateway>

where you rep ace <dest> and <gate-

way> with the destination and gateway

IP addresses.

12. Press Enter to save the destination and

gateway IP addresses.

To Estab ish a Te net Session to

the Cajun P333T via the Network

1. Verify that the Cajun P333T and your PC

are on the same oca network. There are

two ways to ensure this:

• Change the PC’s IP address so that it wi

be on the same subnet as the Cajun

P333T.

LRefer to Chapter 5 of the Cajun P333T

User’s uide for details.

• Change the IP address of the Cajun

P333T.

LRefer to the instructions opposite for

details.

2. Start the Te net session at the prompt by

typing telnet

<cajun_P333T_IP_address>, e.g.,

telnet 149.49.32.134.

3. Enter the User name root when

prompted.

4. Enter the User Leve password root

when prompted.

:You have now estab ished a te net session

to the Cajun P333T and can perform con-

figuration.

Defau t Switch Parameters

Defau t Port Parameters

Configu ation Pa amete Default Setting

Port Speed and Dup ex Mode • 10/100M-TX ports: Auto-negotiation

• 100Base-FX ports: 100 Mbps fu dup ex

• 1000Base-FX ports: 1000 Mbps fu dup ex

F ow Contro • 10/100 and 100 Mbps: Disab ed

• 1000 Mbps: Disab ed (no pause)

Backpressure • 10/100: Enab ed (When in ha f dup ex mode)

• 100Base-FX & 1000 Mbps: Not app icab e

Auto-negotiation • 10/100M-TX ports: Enab ed

• 100Base-FX ports: Not app icab e

• 1000Base-FX ports: Enab ed

Administration State Enab ed

Port VLAN ID 1

Tagging Mode C ear

Port Priority Regu ar

Configu ation Pa amete Default Setting

Cajun P330 IP Address 149.49.32.134

BootP Mode Never

Defau t Gateway 0.0.0.0

Management PC SLIP IP Address 192.168.10.2

VLAN Management ID 1

Spanning Tree Enab ed

TFTP Mode Limited

TFTP Server 0.0.0.0

TFTP Fi e Name viisa

Setting the Mandatory

Parameters

If you wish to change the defau t parameters

shown and configure the mandatory parame-

ters, Lucent recommends that you use the

Command Line Interface (CLI).

LFor further information, please refer to

Chapter 5 of the Cajun P333T User’s

uide.

6. Run the Web-Based

Manager (optiona )

The P330 Web-based Manager a ows you to

configure the P333T switch from your PC.

System Requirements

Minimum hardware and Operating System

requirements are:

• Windows® 95 or NT® 4.0 or higher

• Pentium® 200 Mhz-based computer with

64 Mb of RAM (Pentium-II recommend-

ed)

• Minimum screen reso ution of 1024 x

768 pixe s

• Microsoft® Internet Exp orer® 4 or

higher o

• Netscape Navigator® 4.xor higher

• Sun Microsystems Java™ p ug-in version

1.2.2 (supp ied)

Running the Embedded Manager

LYou should assign an IP address to the

P333T before starting this procedure

1. Open your browser.

2. Enter the URL of the switch in the form

http://aaa.bbb.ccc.ddd

Laaa.bbb.ccc.ddd is the IP address of the

switch

:You are prompted to og into the switch.

LThe user name is “root”

The default password for read-only access

is “root”

The default password for read-write access

is “enable” or “super”

LThe Web management passwords are the

same as those of the CLI. If you change the

passwords in the CLI then use those pass

words for Web management as well.

:The we come page is disp ayed.

:If you have the Java p ug-in insta ed the

Web-based manager shou d open in your

browser.

:If you do not have the Java p ug-in a

message appears.

LIf the network manager has configured the

system the plug-in should be installed

automatically.

There are three ways to install the plug-in

manually:

• Eithe insta the p ug-in from the CD as

fo ows:

1. C ose a unnecessary app ications on

your PC.

2. Insert the “Cajun P330

Documentation and Uti ites” CD in

the CD drive.

3. C ick Start on the Task bar.

4. Se ect Run.

5. Type x:\emweb-aux-files\plug

in_1_2_2.exe (where x: is the CD

drive etter)

6. Fo ow the instructions on screen.

• O insta the p ug-in from the Lucent

site by c icking on the ink on the we -

come page.

• O Insta the p ug-in from oca site by

c icking the ink on the we come page

(on y avai ab e if the network manager

has p aced the fi es on that site).

Documentation and On ine He p

Refer to the Cajun P330 Documentation and

Uti ites CD for fu instructions

Cajun is a trademark of Lucent Techno ogies, Inc.

A other trademarks, registered trademarks, service names, product and/or brand names are the so e property of their respective owners.

Lucent Techno ogies Inc., InterNetworking Systems,

To Free: 1-888-ETHERNET, To Free: (+) 800-CAJUNINF

http://www. ucent.com/ins

Cata og No.: 223555 Rev. 0

Autres manuels pour Cajun P333T

Table des matières

Autres manuels Lucent Technologies Changer

Lucent Technologies

Lucent Technologies 4ESS Manuel utilisateur

Lucent Technologies

Lucent Technologies CBX 3500 Manuel utilisateur

Lucent Technologies

Lucent Technologies LambdaUnite Manuel utilisateur

Lucent Technologies

Lucent Technologies CBX 500 Manuel utilisateur

Lucent Technologies

Lucent Technologies MAX TNT Manuel

Lucent Technologies

Lucent Technologies Cajun P115G Manuel utilisateur

Lucent Technologies

Lucent Technologies 5ESS-2000 Guide d'installation

Lucent Technologies

Lucent Technologies LambdaUnite Manuel utilisateur

Lucent Technologies

Lucent Technologies 4ESS Manuel utilisateur

Lucent Technologies

Lucent Technologies GX 550 Manuel utilisateur

Lucent Technologies

Lucent Technologies GX 550 ES Manuel

Lucent Technologies

Lucent Technologies CAJUN P120 Manuel utilisateur

Lucent Technologies

Lucent Technologies B-STDX Manuel utilisateur

Lucent Technologies

Lucent Technologies Cajun P112T Manuel utilisateur

Lucent Technologies

Lucent Technologies CBX 3500 Manuel utilisateur

Lucent Technologies

Lucent Technologies A500 Manuel utilisateur

Lucent Technologies

Lucent Technologies Cajun P220 Manuel utilisateur

Lucent Technologies

Lucent Technologies LambdaUnite MSS Manuel utilisateur

Lucent Technologies

Lucent Technologies LambdaUnite Manuel utilisateur

Lucent Technologies

Lucent Technologies ED83134-30 Manuel utilisateur

Lucent Technologies

Lucent Technologies CAJUN M770 Manuel utilisateur

Lucent Technologies

Lucent Technologies CAJUN M770 Manuel utilisateur

Lucent Technologies

Lucent Technologies 4ESS Manuel utilisateur

Lucent Technologies

Lucent Technologies Cajun P220 Mode d’emploi

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur