Lockly LATCH EDITION SECURE PGD628 Manuel utilisateur

INSTALLATION

GUIDE

LATCH EDITION

SECURE

PGD628 |PGD628F | PGD628FC

Reference installation parts overview foldout on back page

Welcome!

This guide will walk you through step-by-step how to

install and get your Lockly Secure up and running.

Installation generally takes less than 30 minutes. If

you have any questions please reference our online

support at: Lockly.com/support or call (669) 500-8835

for help.

Preparation

Phillips Screwdriver

To complete the installation you will need:

Flathead Screwdriver Tape measure or ruler

Pliers

（Optional）

Screwdriver with drill bits

Drilling is not required to install the lock, and is optional. However if you are installing your lock on

a brand new door, a drill is required if there are no holes prepared for

lock installation.

Preparation

1-3/8" ~ 2"

(35mm ~ 50mm)

2-1/8"

54mm

4-1/8"

105mm

25mm

Backset

IMPORTANT NOTICE

1/2"

12mm

2-3/8" (60mm)

or 2-3/4" (70mm)

Measure and confirm your door is between

1-3/8" ~

2" (

35mm - 50mm).

Measure and confirm the hole in the door

door is 2-1/8" (54mm).

Measure and confirm that the backset is

between 2-3/8" (60mm) to 2-3/4" (70mm).

Measure and confirm that hole in the door

edge is 1" (25mm).

You are not required to drill an extra hole in your door. We have provided double-sided

adhesive tape for you to help stabilize the lock during installation. Only drill a hole if you

wish to have added stability. Please refer to the provided template for drilling if needed.

Use goggles to protect your eyes if you need to drill door holes.

Remove existing door hardware, latch or deadbolts before installing the new lock.

Use provided template to bore new holes if needed.

*Optional

INSTALLING THE LOCKSET

Step 1

Facing the door exterior, install the lockset according to the in-swing or out-swing opening direction

of your door.

Secure lockset with provided G screws.

LEFT OUT-SWING DOOR

LEFT IN-SWING DOOR

RIGHT OUT-SWING DOOR

RIGHT IN-SWING DOOR

Inside

Outside

Inside

Outside

Inside

Outside

(a)

To ensure normal functions and stable long-term operation of

this lockset, replace your door’s old lockset with the provided

Lockly lockset. The included lockset is designed and optimized

for Lockly smart locks.

Measure the distance between center of front door hole to

the edge of your door. Push the shaft (a) to adjust the lockset

to 2-3/8"(60mm) or 2-3/4"(70mm).

2-3/4"

(70mm)

2-3/8"

(60mm)

Note: the shaft's horizontal

and vertical aligment must

be sustained during installa-

tion to ensure latch will fully

extend and lock securely.

CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS

Step 2

The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below

if you are unsure of you door orientation.

Changing the Exterior Handle Orientation

(Right handle)

Insert key and rotate lock

face so that the two white

dots align as shown.

Hinge

Side

RIGHT IN-SWING DOOR

LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR

LEFT IN-SWING DOOR

Use the provided pin insert Rto push the metal

pin located at the 3 o’clock of the the base handle,

then the other pin at 9 o’clock position. Remove

the

handle once the pins are

compressed.

INTERIOR

EXTERIOR

No need to change door handle

orientation. Skip Step 2.

LEFT-IN SWING and RIGHT OUT-SWING DOORS

require changing the door handle orientation.

Contnue to follow Step 2 to change exterior

and interior door handle orientation.

CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS

Step 2

continued

Check that your handle works

smoothly by giving it a turn up

and down.

Twist key back to horizontal position. The

key can be taken out once it goes back

to the horizontal position.

Rotate the handle 180° to the other side of the

lock.

Using your fingers, press the two pins located on

the left and right side of the the lock to insert

the handle back onto the lock.

Confirm that your installation was complete

by checking if the pins are flush against

the handle, and has popped out. Adjust

the handle accordingly to make sure the

pins are fully decompressed and sits flush

against the surface.

Remove the screw by turning counter

clockwise and rotate the handle 180°

in the direction of the arrow as shown.

Make sure the screw hole is aligned with

the marker as illustrated.

Changing the Interior Handle Orientation

Securely screw clockwise as shown

to complete your handle orientation

change.

CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS

Step 2

continued

PREPARING LOCK FOR INSTALLATION

Step 3

If you drilled a hole in Preparation, use Slotted Barrel Extension Uand use pliers to securely tighten

clockwise. If you did not drill a hole in Preparation, you can leave this pole removed.

Install Spindle Cwith

the holes side into the

base of the lock and

align the holes locate

in the 3 o’clock and

9 o’clock position.

Insert locking pin D

in to the hole as

shown above.

4Peel paper layer OFF the

Adhesive tape and

prepare for installation.

Carefully bend the end

of the locking pin D with

a needle nose pliers.

Failure to bend the locking

pin and turn the handle freely

without obstruction will result

to malfunction.

INSTALLING THE LOCK (EXTERIOR)

Step 4

Exterior

Install the exterior lock as shown to the

left by aligning the lock straight

and

passing the cable and attached rods

through the lockset.

Pass the Spindle Cthrough the center

of the lockset, and the round rods

through the sides in their respective

holes. The cable should run underneath

the lockset.

Align the lock straight and press hard (if

you use the Adhesive tape in step 3.4)

to secure the top of the lock.

Autres manuels pour LATCH EDITION SECURE PGD628

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lockly Serrure de porte

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

Lockly

Lockly LATCH EDITION SECURE PGD628 Manuel utilisateur

Lockly

Lockly SECURE PRO Manuel utilisateur

Lockly

Lockly SECURE PRO Manuel utilisateur

Lockly

Lockly FLEX TOUCH PRO Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION 7S Manuel utilisateur

Lockly

Lockly FLEX TOUCH Manuel utilisateur

Lockly

Lockly DEADBOLT SECURE PLUS Manuel utilisateur

Lockly

Lockly FLEX TOUCH Manuel utilisateur

Lockly

Lockly Secure LUX Manuel utilisateur

Lockly

Lockly LUX Compact Manuel utilisateur

Lockly

Lockly LATCH EDITION SECURE PLUS Manuel utilisateur

Lockly

Lockly Vision Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION 7S Manuel utilisateur

Lockly

Lockly LUX COMPACT PGD688FSN Manuel utilisateur

Lockly

Lockly PRO Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION SECURE PGD728 Manuel utilisateur

Lockly

Lockly DEADBOLT SECURE PLUS Manuel utilisateur

Lockly

Lockly LUX COMPACT PGD688F-MB Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION PGD1128FPW Manuel utilisateur

Lockly

Lockly VISION ELITE Mode d’emploi

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

Lockly

Lockly Secure LUX Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION 7S Manuel utilisateur

Manuels Serrure de porte populaires d'autres marques

Assa Abloy

Assa Abloy effeff 827A-IP Manuel utilisateur

We.lock

We.lock SECBNEBL51 Manuel utilisateur

Iseo

Iseo MA1A Manuel utilisateur

ID Lock

ID Lock 150 Manuel utilisateur

iLoq

iLoq G50S Manuel utilisateur

SDC

SDC Z7835 Manuel utilisateur

ilco

ilco 452 Manuel utilisateur

Samsung

Samsung shs-h705 Manuel utilisateur

TRU-BOLT

TRU-BOLT 08102017 Manuel utilisateur

CDVI

CDVI 500-LADJ Manuel utilisateur

Igloohome

Igloohome Deadbolt 2S Metal Grey Instructions d'installation et d'entretien

eSSL

eSSL FL-300 Manuel utilisateur

JAKO

JAKO JKBTNX4 Manuel utilisateur

Dorma

Dorma MUNDUS PREMIUM GK 50 Guide de l'utilisateur

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Manuel utilisateur

Siegenia

Siegenia KFV AS3500 Manuel utilisateur

Saflok

Saflok Quantum ädesē RFID Manuel utilisateur