Lockly ACCESS TOUCH PRO Manuel utilisateur

INSTALLATION

GUIDE

ACCESS TOUCH PRO

WI-FI CONNECTED

FINGERPRINT DEADBOLT

Enjoy the freedomTM

Welcome!

Reference installation parts overview foldout on back page

This guide will walk you through step-by-step how to install and

get your Lockly Access Touch Pro up and running. Installation

generally takes less than 30 minutes. If you have any questions

please reference our online support at: Lockly.com/support

or call (669) 500-8835 for help.

To complete installation, you would need the following:

Prepare door and remove existing lock. If necessary, use provided

Installation Template to prepare door.

1-⅜" (35mm)

to 2" (50mm)

1" (25mm)

2-⅜" (60mm)

or 2-¾" (70mm)

2-⅛" (54mm)

Preparation

Tape measure or ruler

Flathead Screwdriver

Phillips Screwdriver

*Optional

* Use goggles to protect eyes if you need to drill door holes.

ADJUST DEADBOLT AND INSTALL

Step 1

Deadbolt slot must align to the center of the door hole. Adjust as

shown if needed.

The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8”

(60mm) if necessary (wear gloves to protect from possible pinching).

Hold the metal plate and

twist the deadbolt body

clockwise till it snaps to 2-3/8"

Deadbolt comes set at 2-3/4"

(70mm). To return to default,

while deadbolt is extended,

hold the metal plate and

twist the deadbolt body

counter-clockwise till it snaps

to 2-3/4"

Push the crank to extend

the deadbolt

2-3/4" (70mm)

or 2-3/8” (60mm)

C D

ADJUST DEADBOLT AND INSTALL

Step 1

continued

Extend the deadbolt by inserting

a flat-head screwdriver into the

slot and turning clockwise.

Insert deadbolt to the door edge,

make sure that the right side is up

and the slot is in the vertical position.

Secure with 2 screws.

INSTALLING EXTERIOR ASSEMBLY (B)

Step 2

Before mounting exterior lock assembly

(B) make sure torque blade is in the

vertical position while deadbolt is

extended [1].

Place assembly and torque blade

through the deadbolt slot and guide

connection cables through the cross-

bore hole under the deadbolt as shown.

Align and secure until flush to exterior

door surface.

EXTERIOR VIEW

[1]

Vertical

Extended

Under

INSTALLING EXTERIOR ASSEMBLY (B)

Step 2

continued

TIP: when installing screws by hand, turn screws clockwise several turns then

counterclockwise one turn to ensure smooth threading and no cross threading.

1: Check mounting plate

alignment to door hole before

securing with adhesive strips.

3: Insert, tighten by hand 2

screws located on the left

and right of the blade. Check

alignment and tighten with

screwdriver until mounting plate

securely placed on door.

4: Use the key to ensure deadbolt locks

and unlocks smoothly (no binding or

rubbing). IMPORTANT: when finished,

leave the deadbolt extended and

remove the key before proceeding

to the next step.

2: Align and secure mounting plate

with adhesive strips. Guide connection

cable through and secure to the lower

left notched hole.

Remove key when finished

Leave deadbolt extended

Lockly Access Touch Pro comes with a pre-wired door sensors consisting

of two parts:

Part (P) - Wired

Sensor

Part (Q) - Sensor

Magnet

About door sensors

Door sensors provide real-time door condition status, such as the

ability to verify if the door is securely closed. It also sends push

notifications to your phone whenever your door opens and enables

voice control with Amazon Alexa or Hey Google.

Removal of Sensor (optional)

There may be circumstances where the sensor cannot be installed

because of molding/door limitations or is not aesthetically desirable.

The sensor wired to the lock is removable by carefully pulling its connector

from the circuit board. If removed, some features and functionality

will not be available, such as real-time condition status.

IMPORTANT: Gap must be less than 3/4”

when installed.

When installed on door, the distance between the

wired sensor and sensor magnet must be less than

3/4” in order for the sensor to work.If door frame is

higher than door, add included foam pads to level

parts (P) and (Q) with each other as much as possible.

PREPARING WIRED DOOR SENSOR

Step 3

TIP: Lockly door sensors comes in Grey (PGA715) and Matte

Black (PGA716) that can be ordered through our customer

hotline: (669) 500-8835 or by email: [email protected].

Do not install the wired door sensor yet. You will install in Step 6.

Right

Left

When installing the wired door sensors, make sure the arrow on the

wired sensor Paligns to the arrow of the sensor magnet Qas close

as possible.

The sensors need to be as

close to level as possible. If

needed, use the adhesive

foam pad(s) to adjust the

height of the wired sensor.

Sensors can be positioned

on either left or right side

(see next page).

2-3/4" (70mm)

2-3/8" (60mm)

3/4" (20mm)

Foam pad

(P) (Q)

PREPARING WIRED DOOR SENSOR

Step 3

continued

Insert form

pad

The interior assembly comes

with the pre-installed wired

door sensor setup for a right

swing doors with 2 ¾" (70mm)

backset*.

Trim excess part (P) for doors

with 2 ⅜" (60mm) backset as

shown below.

For left swing doors, re-route

the door sensor wire through

the side channel. Pull the

foam

pad then re-insert to secure the

wire. Discard the excess part

(e) for doors with 2 ⅜" (60mm)

backset

as shown below:

DO NOT INSTALL THE SENSORS YET

Pull foam pad

PREPARING WIRED DOOR SENSOR

(P)

Step 3

continued

Trim excess here for

2 ⅜" (60mm) backset*

*Backset = distance of the door edge to the center of the cross-bore

door hole.

Autres manuels pour ACCESS TOUCH PRO

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lockly Serrure de porte

Lockly

Lockly PRO Manuel utilisateur

Lockly

Lockly VISION ELITE Mode d’emploi

Lockly

Lockly Secure LUX Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION 7S Manuel utilisateur

Lockly

Lockly SECURE PRO Manuel utilisateur

Lockly

Lockly MORTISE EDITION SECURE LUX PGD829AFUS Manuel utilisateur

Lockly

Lockly FLEX TOUCH Manuel utilisateur

Lockly

Lockly FLEX TOUCH PRO Manuel utilisateur

Lockly

Lockly LUX COMPACT PGD688F-MB Mode d’emploi

Lockly

Lockly DEADBOLT SECURE PLUS Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION PGD1128 Manuel utilisateur

Lockly

Lockly LATCH EDITION SECURE PGD628 Manuel utilisateur

Lockly

Lockly FLEX TOUCH Manuel utilisateur

Lockly

Lockly LATCH EDITION SECURE PLUS Manuel utilisateur

Lockly

Lockly LATCH EDITION 6S Manuel utilisateur

Lockly

Lockly Satin Nickel Secure Plus Smart Lock Deadbols Manuel utilisateur

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION 7S Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION PGD1128FPW Manuel utilisateur

Lockly

Lockly DEADBOLT EDITION 7S Manuel utilisateur

Lockly

Lockly Vision Manuel utilisateur

Lockly

Lockly PGD728F Manuel utilisateur

Lockly

Lockly DEADBOLT SECURE PLUS Manuel utilisateur

Lockly

Lockly LUX Compact Manuel utilisateur

Manuels Serrure de porte populaires d'autres marques

Assa Abloy

Assa Abloy effeff 827A-IP Manuel utilisateur

We.lock

We.lock SECBNEBL51 Manuel utilisateur

Iseo

Iseo MA1A Manuel utilisateur

ID Lock

ID Lock 150 Manuel utilisateur

iLoq

iLoq G50S Manuel utilisateur

SDC

SDC Z7835 Manuel utilisateur

ilco

ilco 452 Manuel utilisateur

Samsung

Samsung shs-h705 Manuel utilisateur

TRU-BOLT

TRU-BOLT 08102017 Manuel utilisateur

CDVI

CDVI 500-LADJ Manuel utilisateur

Igloohome

Igloohome Deadbolt 2S Metal Grey Instructions d'installation et d'entretien

eSSL

eSSL FL-300 Manuel utilisateur

JAKO

JAKO JKBTNX4 Manuel utilisateur

Dorma

Dorma MUNDUS PREMIUM GK 50 Guide de l'utilisateur

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Manuel utilisateur

Siegenia

Siegenia KFV AS3500 Manuel utilisateur

Saflok

Saflok Quantum ädesē RFID Manuel utilisateur