Linear Multi-Code 4120 Manuel utilisateur

MODEL 4120 TWO CHANNEL TRANSMITTER

Congratulations! You have just purchased a MULTI-CODE Digital Transmitter,

which we believe to be the ﬁnest product of its kind on the market. With little care

this transmitter should provide you with many years of excellent service. Please

take a moment to read the following instructions and you will ﬁnd that setting your

now transmitter will be quite an easy matter.

ACCESSING THE CODE SWITCH

Insert a small coin into the slot located at the bottom end of the transmitter. Twist

the coin and remove the access cover to expose the code switches and battery

compartment.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,MC4120,2 CH,TX - LINEAR P/N: 214881 B - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 9.000” X 3.500” - SCALE: 1-1 - SIDE 1 OF 2

INSTALLATION INSTRUCTIONS

PLEASE NOTE

Linear LLC has devoted a great deal of time and research in order to provide the

most reliable equipment possible. Certain limitations must be observed.

(1) MULTI-CODE radio components must conform with FCC Part 15 requirements.

For this reason, the range and power of our radios is within speciﬁed limits.

(2) As with all manufacturers, Linear LLC radios must accept all signals that they

receive. This may, in rare instances, create difﬁculty.

(3) You should test your entire system occasionally in order to be sure that all

components areworking in good order.

(4) Linear LLC dealers can provide you with information regarding the use of our radio

controls, and can provide valuable installation and operation information, when

requested.

CAUTION: Any changes or modiﬁcations in intentional or unintentional radiators

which are not expressly approved by LINEAR LLC could void the user’s authority

to operate this equipment. This applies to intentional and unintentional radiators

certiﬁed per Part 15 of the F.C.C. rules and regulations.

LINEAR LLC

(800) 421-1587 • (760) 438-7000

www.linearcorp.com

Channel 1 on the receiver is selected by moving the 10th position of the transmitter

side A to the off (open) position. Channel 2 is selected by moving the 10th position

of the transmitter side B to the on (closed) position. Once the codes have been set,

check the operation and replace the lower cover.

TRANSMITTER INSTALLATION

The transmitter is completely self contained, including battery, and can be operated

while mounted in the car. It is supplied with a clip for attaching to the sun visor, if

desired. If the clip is used, attach to the case by sliding it into the recess provided

on the back of the transmitter until the small dimples ﬁt into the holes in the clip.

WARRANTY

ALL MULTI-CODE door related products carry a eighteen (18) month warranty

against defects in workmanship or material. This warranty begins at the date of

manufacture, for eighteen months. Linear LLC warranties our product only to our

authorized dealers and distributors, and not to the end customer. If you have nay

questions about our warranty, please ask your dealer to determine the nature and

scope of his warranty. Linear LLC does not assume, and is not responsible for,

any real or consequential damages from claims against the performance of our

product, nor is it liable for any costs related to loss of life, property, or revenue.

Further, Linear LLC is in no way responsible for installation of our product, and will

assume no costs to reinstallation or removal. Linear LLC Warranty is in lieu of all

other warranties, expressed, or implied.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,MC4120,2 CH,TX - LINEAR P/N: 214881 B - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 9.000” X 3.500” - SCALE: 1-1 - SIDE 2 OF 2

CODING

Before placing your transmitter into service, we urge you to set your codes, in

order not to interfere with neighboring systems, and to provide security for your

own system. You will note that the model 4120 transmitter has two, ten position

code switches (see ﬁgure 1). We strongly urge that several coding schemes be

avoided: ALL ON; ALL OFF; 2, 4, 6, 8, 10, ON; 1, 3, 5, 7, 9, ON. These positions

are similar to our or other manufacturer’s test positions, or are frequently used.

If you have two single channel receivers: Set your transmitter so that the ten

position switch on side A will match your receiver #1. Set the ten position switch

on transmitter side B to your receiver #2 (see ﬁgure 2).

If you have a MULTI-CODE™ 3021 or 3028 two channel receiver: Set the

receiver and transmitter (side A and B) code switch positions 1-9 to match. The

10th position on your transmitter code switches are used for channel selection.

CODE SWITCH

SIDE A

CODE SWITCH

SIDE B

Figure 2

Figure 1

CODE SWITCH

Table des matières

Autres manuels Linear Émetteur

Linear

Linear ET-2 Instructions d'utilisation

Linear

Linear MULTI-CODE 1051 Manuel utilisateur

Linear

Linear DXT-21/EC Manuel utilisateur

Linear

Linear MULTI-CODE 4140 Manuel utilisateur

Linear

Linear 1094 Manuel utilisateur

Linear

Linear DX DXS-65 Manuel utilisateur

Linear

Linear DOOR/WINDOW TRANSMITTER DXT-31 Manuel utilisateur

Linear

Linear DXS-32 Manuel utilisateur

Linear

Linear Mini-Code 3083 Manuel utilisateur

Linear

Linear GT-31 Manuel utilisateur

Linear

Linear ADVANCED AT7200 Manuel utilisateur

Linear

Linear Delta-3 Series Guide de l'administrateur

Linear

Linear 2 GIG 2GIG-Z-BRDG-433 Guide de configuration

Linear

Linear AT71-250 Manuel utilisateur

Linear

Linear Supervised Emergency Alarm Transmitter... Manuel utilisateur

Linear

Linear Multi-Code MCS1082 Manuel utilisateur

Linear

Linear Multi-Code MCS307010 Manuel utilisateur

Linear

Linear miniTransmitter Delta-3 Series Guide de l'administrateur

Linear

Linear DT-2A Guide de l'administrateur

Linear

Linear MVP Manuel utilisateur

Linear

Linear MDT Manuel utilisateur

Linear

Linear AT7400 Manuel utilisateur

Linear

Linear DX DXT-61 Manuel technique

Linear

Linear MULTI-CODE 3083 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur