LevelOne 55051007 Manuel utilisateur

IGP-0102

Industrial Gigabit POE Injector, 802.3at PoE+, 36W, 12 to 56 VDC

User Manual

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received; including interference that may cause

undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55022 class A for ITE, the essential protection requirement of

Council Directive 2004/108/EC on the approximation of the laws of the Member States

relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible that

information in this document is not up-to-date. Please check with your local distributors for the

latest information. No part of this document can be copied or reproduced in any form without

written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

NOTE:

Always make sure the total length of the TX cable DOES NOT exceed 100meter. Total length is

defined as length A + length B

Length A + Length B < 100 meter

PD Remote Switch

Maximum total cable length is 100meter.

During 100Mbps transmission, the maximum total cable length is 100 meter.

During 1000Mbps speed transmission, recommend maximum cable length less than 90 meter is

more desired.

POE signal attenuates every meter, the built-in transformer allows the attenuation to reach 100

meter long to follow IEEE802.3af / at standard. the higher quality of PD you connected to, the

more reliable the network will be. When connect to a poor quality PD, it can not generate strong

signal to send to remote switch. Always make sure you have a high quality PD to perform a

desired network.

Installation package

This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-

mounted bracket are included.

Wall mount bracket x 2

Din Rail Bracket x 1

4 pin Terminal Block x1

Power connection

The provided 4 pin terminal block can be connected with 48VDC to 56VDC power source. Always

Make sure your input voltage is within this supported voltage range.

Tomake power connection –Follow the printed polarity for V+, V-, Ground. Connect positive wire

to V+ , connect negative wire to V-, also connect neutral wire to ground. This unit can be

connected to two power input.

+V1- is for power input one connection,

+V2-(SW) is for power input two connection.

Connecting procedure

STEP 1 –

Take out 4 pin terminal block located in the included mounting kit package.

STEP 2 –

Connect power wire to +V1- or Connect +V2- (SW) as shown above

STEP 3 –

Plug into terminal block socket shown above. Polarity needs to match the V+ and V-

WARNING -- Always SHUTS OFF power source to connect power wire.

WARNING –any exceeded input voltage will not make this unit function and may damage this unit.

(SW)

+ V1 - + V2 -

LED indicator

PW—Power 1, Power 2

Mode A Green LED ON --

For End-Span POE power 1,2,3,6

NOTE:

Mode B Green LED is only for Mode B End-Span

model. with pin assignment 4,5,7,8. This LED will

not lit on for this model.

Specification:

IEEE Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE 802.3ab 1000Base-T Gigabit Ethernet

IEEE802.3af for POE

IEEE802.3at for POE+

Network Connector :

1xRJ-45 10/100/1000BaseT(X) Data

1xRJ-45 10/100/1000BaseT(X) Data with POE

Output power

Network Cable

UTP/STP above Cat.5e Cable

EIA/TIA-568 10-ohm (100m)

Protocol

CSMA/CD

LED

PW1(power 1) Green: ON- power good, OFF-

power failed

PW2(power 2) Green: ON- power good, OFF-

power failed

POE: ON- POE Normal working,

FLASH- Overload,

OFF- NO POE power detected

POE Pin Assignment

Mode A model, V+, V+, V-, V- for pin 1, 2, 3, 6

Reverse polarity protection

Present

Overload current protection

Present

Power Supply

2 Redundant power source

12V~56V VDC Power Input

Power Consumption

1 W@12/24/48 VDC full load, Without POE

POE power

Maximum POE power 36watts at 12/24/48VDC

input

Removable Terminal Block

Provide 4 pin terminal block

Wire range: 0.34mm^2 to 2.5mm^2

Solid wire (AWG):12-24/14-22

Stranded wire(AWG): 12-24/14-22

Torque:5lb-In/0.5Nm/0.56Nm

Wire Strip length: 7-8mm

Operating Temperature

-40℃~75℃fully tested.

Operating Humidity

5% to 95% (Non-condensing)

Storage Temperature

-40℃~85℃

MTBF (mean time between failure)

510,304 hrs ( MIL-HDBK-217F) at 25°C

Housing

Rugged Metal ,IP30 Protection

Case Dimension (L X W X D)mm

103.5mmx32mmx81.5mm (LxWxD)

Installation mounting

DIN Rail mounting and Wall Mounting

Certifications:

EN55022/24

ITE equipment

Safety

IEC EN60950-1

EMC/EMS

CE, FCC, VCCI

EMI

FCC Part 15 Subpart B Class A,

CE EN 55022 Class A

EN 50155 / EN 60068-2-6

Vibration

EN 50155 / EN 60068-2-27

Shock

EN 50155 / EN 60068-2-32

Free Fall

Housing Dimension

Multilingual Quick Guide

IGP-0102

Industrial Gigabit POE Injector

Power connection

This unit provides 4 pin terminal block. The PoE port can be operated from 48-56VDC power source

input.

Power connecting procedure:

STEP 1 – Pull out 4 pin terminal block.

STEP 2 – Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.

STEP 3– Plug back 4 pin terminal block to its place.

Stromanschluss

Dieses Gerät verfügt über einen 4-poligen Anschlussblock. Der PoE-Anschluss kann über den

Stromeingang mit 48 bis 56 V Gleichspannung betrieben werden.

Stromanschlussverfahren:

Schritt 1 – 4-poligen Anschlussblock herausziehen.

Schritt 2 – Draht mit V1+, V1- oder V2+, V2- und Erde, Neutralleiter mit Erdungsschraube verbinden.

Schritt 3 – 4-poligen Anschlussblock wieder anbringen.

Connexion de l’alimentation

Cet unité dispose d'un bornier à 4 broches. Le port PoE peut être utilisé avec une entrée d’alimentation

de 48-56Vcc.

Procédure de connexion de l’alimentation :

ÉTAPE 1 – Sortez le bornier à 4 broches.

ÉTAPE 2 – Connectez le fil à V1+, V1- ou à V2+, V2-, et reliez le fil neutre à la terre avec la vis de terre.

ÉTAPE 3– Rebranchez le bornier à 4 broches à sa place.

Conexión de alimentación

Esta unidad proporciona un bloque de terminales de 4 contactos. El puerto PoE se puede utilizar con

una entrada de fuente de alimentación de entre 48 y 56 VCC.

Procedimiento de conexión de alimentación:

PASO 1: Saque el bloque de terminales de 4 contactos.

PASO 2: Conecte el cable a V1+, V1-, o V2+, V2- y conecte el cable de tierra al tornillo de toma de tierra.

PASO 3: Vuelva a enchufar el bloque de terminales de 4 contactos en su lugar.

Ligação de alimentação

Esta unidade fornece um bloco terminal de 4 pinos. A porta PoE pode ser utilizada através da entrada

de fonte de alimentação 48-56VDC.

Procedimento de ligação de alimentação:

PASSO 1 – Puxe pelo bloco terminal de 4 pinos.

PASSO 2 – Ligue o cabo a V1+, V1-, ou V2+, V2-, e o cabo neutro ao parafuso de ligação à terra.

PASSO 3– Volte a ligar o bloco terminal de 4 pinos no seu lugar.

Collegamento dell'alimentazione

Questa unità fornisce una morsettiera a 4 pin. La porta PoE può essere azionata dall'ingresso della fonte

di alimentazione a 48-56 V CC.

Procedura di collegamento dell'alimentazione:

FASE 1 – Estrarre la morsettiera a 4 pin.

FASE 2 – Collegare il cavo a V1+, V1- o V2+, V2- e terra e il cavo neutro alla vite di messa a terra.

FASE 3 – Collegare di nuovo la morsettiera a 4 pin in posizione.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LevelOne Changer

LevelOne

LevelOne GEP-2681 Manuel utilisateur

LevelOne

LevelOne GSW-0503T Manuel utilisateur

LevelOne

LevelOne FSW-0513 Manuel utilisateur

LevelOne

LevelOne Infinity IES-2880 Manuel utilisateur

LevelOne

LevelOne ProCon GSW-1290 Manuel utilisateur

LevelOne

LevelOne FSW-0507TX Manuel utilisateur

LevelOne

LevelOne ProCon GSW-4896 Manuel utilisateur

LevelOne

LevelOne POH-0850TX Manuel utilisateur

LevelOne

LevelOne Infinity IES-1082 Manuel utilisateur

LevelOne

LevelOne ViewCon KVM-0850 Manuel utilisateur

LevelOne

LevelOne OfficeCon GSW-2440 Manuel utilisateur

LevelOne

LevelOne GTL-2872 Manuel utilisateur

LevelOne

LevelOne FEP-1601 Manuel utilisateur

LevelOne

LevelOne IFP-0503 Manuel utilisateur

LevelOne

LevelOne FEP-1601 Manuel utilisateur

LevelOne

LevelOne GEU-0520 Manuel utilisateur

LevelOne

LevelOne GEP-2450 Manuel utilisateur

LevelOne

LevelOne IES-0610 V2 Manuel utilisateur

LevelOne

LevelOne FEP-0800 Manuel utilisateur

LevelOne

LevelOne GSW-0509 Manuel utilisateur

LevelOne

LevelOne GEU-2429 Manuel utilisateur

LevelOne

LevelOne GEP-5070 Manuel utilisateur

LevelOne

LevelOne GEP-0820 Manuel utilisateur

LevelOne

LevelOne KVM-0260 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur