LevelOne IGP-0521 Manuel utilisateur

IGP-0521

5-Port Industrial Gigabit Ethernet PoE Switch, 4 PoE Outputs

+ 1 SFP/TX Combo, 126W, 12/24/48VDC

User Manual

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received; including interference that

may cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55022 class A for ITE, the essential protection requirement of

Council Directive 2004/108/EC on the approximation of the laws of the Member

States relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible

that information in this document is not up-to-date. Please check with your local

distributors for the latest information. No part of this document can be copied or

reproduced in any form without written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

Introduction

This rugged designed Industrial Ethernet switch / Industrial Giga -bit 4 port POE Injectors and

Super Booster Industrial Giga-bit 4 port POE Injectors, which comply with IEEE802.3af and

IEEE802.3at, has pass many rigorous environmental test. It delivers 30watts power (Max 36W) per

POE port. And it can generate total 120 watts power(Max 126W) to PD devices. the uplink 2 SFP

port (varied by models), can extend your environment to a much larger area.

The super voltage booster model uses 12/24/48VDC input to boo st voltage to 55VDC. It guaranty

to meet IEE802.3at and to delivery full POE power up to 36Watts per POE port to a PD. With its

multi-purpose design, it can also be used for Din-Rail or wall-mounted. It is an ideal unit for IP

surveillance, traffic monitoring and Security application in critical environment. It can tolerate -

40°C to 75°C in harsh environment to perform a reliable network.

Housing Dimension

MODELS –Super Booster Industrial Giga-bit 4 port POE Injector, 12/24/48 VDC input

This Super Voltage Booster --- The high power 4 port industrial POE+ Injector is

equipped with our high efficiency ColdDesign technology which allows low input

voltage, such as 12/24/48VDC be boost up to 55VDC to meet IEEE802.3at requirement.

The ColdDesign technology will not only boost up Input Voltage, also reduce the

excessive heat problem to a minimum. It accepts the input voltage as low as 12VDC, to

be boost up to 55VDC. And it is also equipped with 2 port SFP fiber that can be used as

fiber redundancy, cascaded to your other devices to expand your network application. It

is being rigorously tested for your Security, Transportation and Telco application.

Power connection

This unit provides 6 pin terminal block. The POE port can be operated from 44-56VDC power source. The

VDC power range can be 48VDC only or lower, or wide range from 44-56VDC. Always Make sure your

input voltage is within this supported voltage range for each model.

WARNING –any exceeded input voltage will not make this unit function and may damage this unit.

To make power connection –Follow the printed polarity for V1+, V1-,

V2+, V2-, and ground. Connect positive wire to V+ , connect negative

wire to V-, also connect neutral wire to the ground screw as shown .

Relay -- You may use 24V@1Arelay connection to your external

device for special purpose. When 2 powers are connected, the relay is

in SHORT mode. When any power source fails, the relay change to

OPEN status.

Power connecting procedure:

STEP 1 –Pull out 6 pin terminal block.

STEP 2 –Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.

STEP 3–Plug back 6 pin terminal block to its place.

WARNING –

Always ground the power source to maintain a clean power input. Due to too many cheap made power

supplies, it creates too much noise, and it will cause the power input fluctuates when connect to this

unit. To avoid this, always ground the power source to gain a clean power input.

Din Rail Bracket x 1

Wall mount bracket x 2

6 pin Terminal Block

Installation package

This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted

bracket are included.

Dip switch function

SPD

ON –1000M speed is detected.

OFF –10M or 100M speed is detected

PW1

ON -- when V1+, V1- is connected

LNK

ON—TX link is detected

OFF –TX port is not detected

Flashing –TX port is active

LED indicator

This unit is equipped with dip switches, located on the front panel. Adjusting the dip switches will change

the default function of this unit. This unit has set to manufacturer default as: Port 5 SFP and the speed is

set to 1000M for both port 5 and port 6 SFP ports. you may adjust dip switch setting to select port 5 as TX

( disable port 5 SFP) or set SFP speed to 100M. The detail setting as shown below:

PW2

ON -- when V2+, V2- is connected

ERR

ON –

connect only PW1 or PW2.

OFF-

both PW1 and PW2 are connected

ON –port 5 SFP fiber is detected

OFF –port 5 SFP fiber is not detected.

Flashing –port 5 SFP fiber is active

P1,P2,P3,P4

ON—PD is detected on designated port.

OFF –no PD is detected

Warning:

Dip switch function will not work if it is

changed when power is connected.

Always turn off or disconnect power

supply to change dip switch settings.

Specification:

IEEE Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE 802.3ab 1000Base-T Gigabit Ethernet

IEEE 802.3z 1000Base-X Gigabit Ethernet

IEEE802.3x Flow Control and Back Pressure,

IEEE802.3af for POE

IEEE802.3at for POE+

Switch Architecture

Back-plane (Switching Fabric): 12Gbps

Data Processing

Store and Forward

Flow Control:

IEEE 802.3x Flow Control and Back Pressure

Jumbo Frame

9KB

MAC address Table Size

Packet Buffer Size

Network Connector :

5xRJ-45 10/100/1000BaseT(X) auto negotiation,

4 Giga POE+ 802.3at/af PSE port

Auto MDI/MDI-X function, Full/Half duplex

1x SFP 100/1000M BaseX

Network Cable

UTP/STP above Cat.5e Cable

EIA/TIA-568 10-ohm (100m)

Fiber Cable (Multi-mode):50/125um,62.5/125um

Fiber Cable (Single-mode): 9/125um

Protocol

CSMA/CD

LED

PW1(Power 1) Green,

PW2(Power 2) Green,

ERR( Fault ) Amber,

TX/RJ-45 port:

LNK (Link/Active) Green,

SPD(Speed) 10/100(OFF ) ,1000 (Green)

SFP Fiber Per port:

Link (Green)

Active Flash

DIPSwitch

DIP 1: OFF: Port 5 SFP (DEFAULT)

ON: Port 5 TX

DIP 2: OFF: SFP 1000M (DEFAULT)

ON: SFP 100M

Reserve polarity protection

Present

Overload current protection

Present

Power Supply

Redundant Dual DC 9V-56V Power Input without

POE

Power Consumption

5.76W@12/24/48 VDC full load, Without POE

Alarm Relay Contact

Relay outputs with current carrying capacity of 1 A

@24VDC,

Relay in short circuit mode when 2 powers are

connected. in open circuit mode when only one

power supply is connected

Ethernet Switch power input

Ethernet switch power input 9VDC -56VDC

POE power

POE power per port 30watts. Maximum 36Watts

Maximum total power 126Watts at 24VDC and

48VDC power input.

Maximum total power 65W at 12VDC power input .

Removable Terminal Block

Provide 2 Redundant power , Alarm relay contact ,6

Wire range: 0.34mm^2 to 2.5mm^2

Solid wire (AWG):12-24/14-22

Stranded wire(AWG): 12-24/14-22

Torque:5lb-In/0.5Nm/0.56Nm

Wire Strip length: 7-8mm

Operating Temperature

-40℃~75℃fully tested.

Operating Humidity

5% to 95% (Non-condensing)

Storage Temperature

-40℃~85℃

MTBF (mean time between failure)

510,304 hrs ( MIL-HDBK-217F) at 25°C

Housing

Rugged Metal ,IP30 Protection

Case Dimension (L x W x D)

142mmx43mmx105mm (LxWxD)

Installation mounting

DIN Rail mounting and Wall Mounting

EMC/EMS

CE, FCC,VCCI

EMI

FCC Part 15 Subpart B Class A,

CE EN 55022 Class A

Table des matières

Autres manuels LevelOne Routeur réseau

LevelOne

LevelOne WBR-6006 Manuel utilisateur

LevelOne

LevelOne WBR-6802 Manuel utilisateur

LevelOne

LevelOne WBR-2401 Manuel utilisateur

LevelOne

LevelOne NetCon WBR-3408 Manuel utilisateur

LevelOne

LevelOne NetCon FBR-4000 Manuel utilisateur

LevelOne

LevelOne WBR-3470 Manuel utilisateur

LevelOne

LevelOne FEU-0510 Manuel utilisateur

LevelOne

LevelOne WBR-6801 Manuel utilisateur

LevelOne

LevelOne WAC-2003 Manuel utilisateur

LevelOne

LevelOne FSW-0511 Manuel utilisateur

LevelOne

LevelOne WBR-3405TX Manuel utilisateur

LevelOne

LevelOne WBR-3407 Manuel utilisateur

LevelOne

LevelOne FSW-0511 Manuel

LevelOne

LevelOne FBR-1700TX Manuel utilisateur

LevelOne

LevelOne FSW-0811 Manuel utilisateur

LevelOne

LevelOne GTL-2660 Manuel utilisateur

LevelOne

LevelOne FBR-1100TX Manuel utilisateur

LevelOne

LevelOne IFE-0501 Manuel utilisateur

LevelOne

LevelOne GEL-2670 Manuel utilisateur

LevelOne

LevelOne FBR-1406TX Manuel utilisateur

LevelOne

LevelOne FSW-1650 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

LevelOne

LevelOne GEU-0807 Manuel utilisateur

LevelOne

LevelOne PLI-2021 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité