LevelOne FSW-1650 Manuel utilisateur

FSW-1650

FSW-2450

User Manual

16/24 10/100 Rackmount Switch

V3.0..0906

Specifications are subject to change without notice. LevelOne is a registered

trademark of Digital Data Communications Asia Co., Ltd. Other brands and

product names are trademarks or registered trademarks of their respective

holders.

No part of the specifications may be reproduced in any form or by any means or

used to make any derivative such as translation, transformation, or adaptation

without permission from Digital Data Communications Asia Co., Ltd. All rights

reserved.

FCC STATEMENT

The Switch has been tested and found to comply with the limits for a class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

¾Reorient or relocate the receiving antenna.

¾Increase the separation between the equipment and receiver.

¾Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

¾Consult the dealer or an experienced radio/TV technician for help.

EC DECLARATION OF CONFORMITY (EUROPE)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/

EEC, this product meets the requirements of the following standards:

¾EN55022

¾EN55024

¾EN60950

SAFETY NOTICES

Caution:

Do not use this product near water, for example, in a wet basement or near a

swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk

of electric shock from lightning.

Package Contents:

The following contents should be found in your box:

¾One FSW-1650 / FSW-2450 Switch

¾One power cord

¾This User's Guide

¾Mounting screws and two “L” planks

)Note:

Make sure that the package contains the above items. If any of the

listed items are damaged or missing, please contact with your

distributor.

CONTENTS

Chapter 1 Introduction of the Product ...........................................1

1.1Overview of the product ............................................................... 1

1.2Features.......................................................................................1

1.3IEEE 802.1p QoS.........................................................................2

Chapter 2 Installation.......................................................................3

2.1Mounting the Switch on a Desk....................................................3

2.2Mounting the Switch in a Rack.....................................................3

2.3Power on......................................................................................4

Chapter 3 Identifying External Components..................................4

3.1Front Panel................................................................................... 4

3.2Rear Panel...................................................................................5

Appendix A: Specifications.............................................................6

Appendix B: Troubleshooting.........................................................7

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Chapter 1 Introduction of the Product

This chapter describes the features of the model of FSW-1650/FSW-2450

16/24- port 10/100 Rackmount Switch. FSW-1650 and FSW-2450 just

differ in the number of LED indicators and ports, all figures in this guide

are of FSW-2450.

1.1 Overview of the product

FSW-1650/FSW-2450 6/24-port 10/100 Rackmount Switch provides

16/24 10/100Mbps Auto-Negotiation RJ45 ports. Each port of the FSW-

1650/FSW-2450 supports auto MDI/MDI-X function, eliminating the need

for crossover cables or Uplink ports. The Switch is Plug- and-Play and

any port can be simply plugged into a server, a hub or a switch, using

straight cable or crossover cable.

The LevelOne FSW-1650/FSW-2450 16/24-port 10/100 Rackmount

switch provides you with a low-cost, easy-to-use, high-performance,

seamless and standard upgrade to improve your old network to a

100Mbps network. It will boost your network performance up to full duplex

data transfer.

1.2 Features

¾Complies with IEEE802.3, IEEE802.3u standards

¾Support IEEE 802.1p QoS

¾16/24 10/100M Auto-NegotiationRJ45portssupporting Auto-

MDI/MDIX

¾Supports IEEE802.3X flow control for full-duplex mode and

backpressure for half-duplex mode

¾LED indicators for monitoring power, link, activity, speed (FSW-2450)

¾Standard 19” rack-mountable steel case

¾Internal power supply

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

1.3 IEEE 802.1p QoS

The FSW-1650/2450 16/24-Port 10/100M switch supports 802.1p priority

queuing Quality of Service, which is an implementation of the IEEE

802.1p standard. With 802.1p QoS function, you can reserve

bandwidth for important functions that require a large bandwidth or have a

high priority, such as VoIP (voice-over Internet Protocol), web browsing

applications or video conferencing. The switch has separate hardware

queues on every physical port which packets from various applications

are mapped to and assigned a priority to. The illustration below shows

how 802.1p priority queuing is implemented on the switch.

The switch has two priority queues labeled 0 and 1. The untagged

packets and the eight IEEE 802.1p priority levels defined by the standard

are mapped to the two class queues used on the switch. Class 1 has

the higher priority of the two priority queues on the switch. The untagged

packets and eight priority tags, specified in IEEE 802.1p are mapped to

the switch’s priority as follows:

The untagged packets and priority 0,1,2 and 3 are assigned to the

switch’s class 0 queue.

Priority 4,5,6, and 7 are assigned to the switch’s Class 1 queue.

The Switch uses WRR( Weighted Robin Round) for scheduling. WRR

queue-scheduling algorithm schedules all the queues in turn and every

queue can be assured of a certain service time. The default weight

value of Class 0 queue and Class 1 queue is 1 to 8.

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Chapter 2 Installation

2.1 Mounting the Switch on a Desk

Before placing the Switch on a desk, attach four rubber feet to the flutes

on the Switch bottom, then lay the Switch on the desktop,

where it is able to withstand 5kg of weight.

)Note:

Make sure there is a grounded AC outlet within 1.5 meters, and

working well. Make sure there is free space for radiating heat

and air.

Make sure not to place anything to heavy on top of the switch.

2.2 Mounting the Switch in a Rack

The dimension of FSW-1650 / FSW-2450 is designed according to the

standard 19” rack-mountable steel case of Electronic Industries

Association.

Powers off all the equipment connected to the Switch before mounting it

in the rack, then rivet the two “L” brackets onto each side of the Switch,

and fasten it with screws in the rack.

Figure 2-1 Rivet the ‘L’brackets onto the Switch

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Figure 2-2 Fasten the Switch in the rack

2.3 Power on

The FSW-1650/FSW-2450 16/24-port 10/100 Rackmount switch is

by power cord. Powering on the Switch, it will be automatically initialized

and the LED indicators should respond as follows:

1) All of the LED indicators will flash momentarily for one second,

which represent a resetting of the system.

2) The Power LED indicator will light up.

Chapter 3 Identifying External Components

This Chapter describes the front panel, rear panel and LED indicators of

the Switch.

3.1 Front Panel

The front panel of FSW-2450 consists of switch model, switch LED

indicators, and 24 10/100Mbps RJ-45 ports.

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Figure 3-1 FSW-2450 Switch Front Panel sketch

3.2 Rear Panel

The rear panel of FSW-2450 only features an electrical outlet, which is an

AC electrical outlet. Connect the female of the power cord head here, and

the male head to the AC power.

Figure 3-2 FSW-2450 Switch Rear Panel sketch

LED indicators

The LED indicators include Power, Link/Act LED indicators, which are

used for monitoring and pre-troubleshooting of the Switch. The following

section shows the LED indicators of the Switch along with an explanation

of each indicator.

Figure 3-3 FSW-2450 Switch LEDs sketch

¾Power LED: This indicator will light solid red when the Switch

powers up. If the LED is not lit, please check the power supply and

connection.

¾LINK/ACT LED: The LED indicates Link/Active status. The

corresponding LED indicator will light solid green when connected to

a network device. It flashes green when data is being transmitted or

received on the working connection.

¾100Mbps: The corresponding gigabit port LED indicator will light

solid green when it's working on 100Mbps speed, not lit when

working on 10Mbps speed.

Autres manuels pour FSW-1650

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LevelOne Routeur réseau

LevelOne

LevelOne NetCon FBR-4000 Manuel utilisateur

LevelOne

LevelOne WBR-3405TX Manuel utilisateur

LevelOne

LevelOne GSW-2473 Manuel utilisateur

LevelOne

LevelOne WBR-3600 Manuel utilisateur

LevelOne

LevelOne FEP-1611 Manuel utilisateur

LevelOne

LevelOne FBR-1700TX Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

LevelOne

LevelOne WBR-6802 Manuel utilisateur

LevelOne

LevelOne NetCon FBR-4000 Manuel utilisateur

LevelOne

LevelOne PLI-2030 Manuel utilisateur

LevelOne

LevelOne WAP-0004 Manuel utilisateur

LevelOne

LevelOne GSW-5150 Manuel utilisateur

LevelOne

LevelOne IFE-0501 Manuel utilisateur

LevelOne

LevelOne PLI-2021 Manuel utilisateur

LevelOne

LevelOne FRT-2101TX Manuel utilisateur

LevelOne

LevelOne WBR-3470 Manuel utilisateur

LevelOne

LevelOne NetCon WBR-3408 Manuel utilisateur

LevelOne

LevelOne GEL-2461 Manuel utilisateur

LevelOne

LevelOne FHU-0803TXD Manuel utilisateur

LevelOne

LevelOne FBR-1407 Manuel utilisateur

LevelOne

LevelOne WGR-8032 Manuel utilisateur

LevelOne

LevelOne WBR-6603 Manuel utilisateur

LevelOne

LevelOne FSW-0508TX Manuel utilisateur

LevelOne

LevelOne GEU-0822 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité