Leica FlexLine plus Manuel utilisateur

Leica FlexLine plus

User Manual

Version 5.0

English

FlexLine plus, Introduction 2

Introduction

Purchase Congratulations on the purchase of a FlexLine plus instrument.

This manual contains important safety directions as well as instructions for setting up

the product and operating it. Refer to "1 Safety Directions" for further information.

Read carefully through the User Manual before you switch on the product.

Product identifica-

tion

The model and serial number of your product are indicated on the type plate.

Always refer to this information when you need to contact your agency or Leica

Geosystems authorised service workshop.

Trademarks • Windows is a registered trademark of Microsoft Corporation.

•

Bluetooth

®is a registered trademark of Bluetooth SIG, Inc.

All other trademarks are the property of their respective owners.

Validity of this

manual

WARNING

Description

General This manual applies to TS02 plus, TS06 plus, and TS09 plus instru-

ments. Where there are differences between the various instru-

ments they are clearly described.

For the Tunnel application, refer to the separate manual "Leica

FlexLine plus Tunnel Application".

Telescope •Measuring with Prism mode: When measuring distances to a

reflector with Electronic Distance Measurement (EDM) mode

"Prism", the telescope uses a wide visible red laser beam, which

emerges coaxially from the telescope's objective.

•Measuring with Non-Prism modes: Instruments that are

equipped with a reflectorless EDM additionally offer the EDM

mode "Non-Prism". When meauring distances with this EDM

mode, the telescope uses a narrow visible red laser beam, which

emerges coaxially from the telescope's objective.

Do NOT remove the battery during operation of the instrument, or during the shut-

down procedure.

This can result in a file system error and data loss!

Always switch off the instrument by pressing the On/Off key, and wait until the

instrument has shutdown completely before removing the battery.

TSOX_135

FlexLine plus, Introduction 3

myWorld@Leica Geosystems (https://myworld.leica-geosystems.com) offers a

wide range of services, information and training material.

With direct access to myWorld, you are able to access all relevant services whenever

it is convenient for you, 24 hours a day, 7 days per week. This increases your efficiency

and keeps you and your equipment instantly updated with the latest information from

Leica Geosystems.

Service Description

myProducts Add all products that you and your company own and explore your

world of Leica Geosystems: View detailed information on your prod-

ucts and update your products with the latest software and keep up-

to-date with the latest documentation.

myService View the current service status and full service history of your prod-

ucts in Leica Geosystems service centres. Access detailed informa-

tion on the services performed and download your latest calibration

certificates and service reports.

mySupport View the current service status and full service history of your prod-

ucts in Leica Geosystems service centres. Access detailed informa-

tion on the services performed and download your latest calibration

certificates and service reports.

myTraining Enhance your product knowledge with Leica Geosystems Campus -

Information, Knowledge, Training. Study the latest online training

material on your products and register for seminars or courses in

your country.

myTrusted

Services

Add your subscriptions and manage users for Leica Geosystems

Trusted Services, the secure software services, that assist you to

optimise your workflow and increase your efficiency.

FlexLine plus, Table of Contents 4

Table of Contents

In this manual Chapter Page

1SafetyDirections 8

1.1 General 8

1.2 Definition of Use 9

1.3 Limits of Use 9

1.4 Responsibilities 9

1.5 Hazards of Use 10

1.6 Laser Classification 12

1.6.1 General 12

1.6.2 Distancer, Measurements with Reflectors 12

1.6.3 Distancer, Measurements without Reflectors

(Non-Prism mode) 13

1.6.4 Red Laser Pointer 15

1.6.5 Electronic Guide Light EGL 17

1.6.6 Laser Plummet 17

1.7 Electromagnetic Compatibility EMC 19

1.8 FCC Statement, Applicable in U.S. 20

2 Description of the System 22

2.1 System Components 22

2.2 Container Contents 23

2.3 Instrument Components 24

3UserInterface 26

3.1 Keyboard 26

3.2 Screen 27

3.3 Status Icons 28

3.4 Softkeys 30

3.5 Operating Principles 31

3.6 Pointsearch 32

3.7 Graphic Symbols 33

4Operation 34

4.1 Instrument Setup 34

4.2 Working with the Battery 37

4.3 Data Storage 38

4.4 Main Menu 38

4.5 Q-Survey Program 39

4.6 Distance Measurements - Guidelines for Correct Results 40

5 Settings 41

5.1 Work Settings 41

5.2 Regional Settings 43

5.3 Data Settings 46

5.4 Screen & Audio Settings 47

5.5 EDM Settings 49

5.6 Interface Settings 53

6 Programs - Getting Started 55

6.1 Overview 55

6.2 Starting a Program 56

6.3 Setting the Job 57

6.4 Station Setup 58

FlexLine plus, Table of Contents 5

7Programs 59

7.1 Common Fields 59

7.2 Station Setup 60

7.2.1 Starting 60

7.2.2 Measuring the target points 62

7.2.3 Station Setup Results 63

7.3 Surveying 65

7.4 Stakeout 66

7.5 Reference Line 69

7.5.1 Overview 69

7.5.2 Defining the Base Line 69

7.5.3 Defining the Reference Line 70

7.5.4 Measure Line & Offset 72

7.5.5 Stakeout 73

7.5.6 Grid Stakeout 75

7.5.7 Line Segmentation 77

7.6 Reference Arc 79

7.6.1 Overview 79

7.6.2 Defining the Reference Arc 79

7.6.3 Measure Line & Offset 81

7.6.4 Stakeout 82

7.7 Reference Plane 84

7.8 Tie Distance 86

7.9 Area & DTM Volume 88

7.9.1 Overview 88

7.9.2 2D / 3D Area 89

7.9.3 Area to Reference Plane 90

7.9.4 DTM Volume 91

7.9.5 Area Division 93

7.10 Remote Height 95

7.11 COGO 96

7.11.1 Starting 96

7.11.2 Inverse and Traverse 96

7.11.3 Intersections 97

7.11.4 Offsets 98

7.11.5 Line - Extension 99

7.12 Road 2D 100

7.13 Road 3D 102

7.13.1 Starting 102

7.13.2 Basic Terms 103

7.13.3 Creating or Uploading Alignment Files 107

7.13.4 Stake 108

7.13.5 Check 109

7.13.6 Stake Slope 110

7.13.7 Check Slope 113

7.14 Traverse 114

7.14.1 Overview 114

7.14.2 Starting and Configuring Traverse 115

7.14.3 Measuring Traverse 116

7.14.4 Moving ahead 118

7.14.5 Closing a Traverse 119

7.15 Tunnel 121

FlexLine plus, Table of Contents 6

8Favourites 122

8.1 Overview 122

8.2 Target Offset 123

8.2.1 Overview 123

8.2.2 Cylindrical Offset Subprogram 124

8.3 Hidden Point 126

8.4 Check Tie 127

8.5 EDM Tracking 128

8.6 Backsight Check 128

8.7 SketchPad 129

9Coding 130

9.1 Coding 130

9.2 Quick Coding 132

10 MapView Interactive Display Feature 133

10.1 Overview 133

10.2 Accessing MapView 133

10.3 Configuring MapView 133

10.4 MapView Components 134

10.4.1 Screen Area 134

10.4.2 Keys, Softkeys and Toolbar 135

10.4.3 Point Symbols 135

10.5 Selecting Points 136

11 Imaging & Sketching 137

11.1 Screenshot 137

11.2 Sketching 137

11.3 Image Management 138

12 Tools 139

12.1 Adjust 139

12.2 Startup Sequence 140

12.3 System Information 141

12.4 Licence Keys 143

12.5 Instrument Protection with PIN 144

12.6 Loading Software 145

13 Data Management 146

13.1 Manage 146

13.2 Exporting Data 147

13.3 Importing Data 150

13.4 Working with a USB Memory Stick 152

13.5 Working with Bluetooth 153

13.6 Working with Leica Instrument Tools 154

14 Check & Adjust 155

14.1 Overview 155

14.2 Preparation 155

14.3 Adjusting Line-of-Sight and Vertical Index Error 156

14.4 Adjusting the Compensator 158

14.5 Adjusting the Tilting Axis Error 159

14.6 Adjusting the Circular Level of the Instrument and Tribrach 160

14.7 Inspecting the Laser Plummet of the Instrument 161

14.8 Servicing the Tripod 162

FlexLine plus, Table of Contents 7

15 mySecurity 163

16 Care and Transport 165

16.1 Care 165

16.2 Transport 165

16.3 Storage 166

16.4 Cleaning and Drying 166

17 Technical Data 167

17.1 Angle Measurement 167

17.2 Distance Measurement with Reflectors 167

17.3 Distance Measurement without Reflectors (Non-Prism mode) 169

17.4 Distance Measurement Reflector (>4.0 km) 170

17.5 Conformity to National Regulations 171

17.5.1 Products without Communication side cover 171

17.5.2 Products with Communication side cover 171

17.5.3 Dangerous Goods Regulations 172

17.6 General Technical Data of the Instrument 173

17.7 Scale Correction 176

17.8 Reduction Formulas 178

18 Software Licence Agreement 179

19 Glossary 180

Appendix A Menu Tree 182

Appendix B Directory Structure 184

FlexLine plus, Safety Directions 8

1SafetyDirections

1.1 General

Description The following directions enable the person responsible for the product, and the

person who actually uses the equipment, to anticipate and avoid operational hazards.

The person responsible for the product must ensure that all users understand these

directions and adhere to them.

About Warning

Messages

Warning messages are an essential part of the safety concept of the instrument. They

appear wherever hazards or hazardous situations can occur.

Warning messages...

• make the user alert about direct and indirect hazards concerning the use of the

product.

• contain general rules of behaviour.

For the users‘ safety, all safety instructions and safety messages shall be strictly

observed and followed! Therefore, the manual must always be available to all persons

performing any tasks described here.

DANGER, WARNING, CAUTION and NOTICE are standardised signal words for iden-

tifying levels of hazards and risks related to personal injury and property damage. For

your safety, it is important to read and fully understand the following table with the

different signal words and their definitions! Supplementary safety information

symbols may be placed within a warning message as well as supplementary text.

Type Description

DANGER Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING Indicates a potentially hazardous situation or an unintended

use which, if not avoided, could result in death or serious injury.

CAUTION Indicates a potentially hazardous situation or an unintended

use which, if not avoided, may result in minor or moderate

injury.

NOTICE Indicates a potentially hazardous situation or an unintended

use which, if not avoided, may result in appreciable material,

financial and environmental damage.

Important paragraphs which must be adhered to in practice as

they enable the product to be used in a technically correct and

efficient manner.

FlexLine plus, Safety Directions 9

1.2 Definition of Use

Intended use • Measuring horizontal and vertical angles.

• Measuring distances.

• Recording measurements.

• Visualizing the aiming direction and vertical axis.

• Data communication with external appliances.

• Computing by means of software.

Reasonably

forseeable misuse

• Use of the product without instruction.

• Use outside of the intended use and limits.

• Disabling safety systems.

• Removal of hazard notices.

• Opening the product using tools, for example screwdriver, unless this is permitted

for certain functions.

• Modification or conversion of the product.

• Use after misappropriation.

• Use of products with obvious damages or defects.

• Use with accessories from other manufacturers without the prior explicit approval

of Leica Geosystems.

• Deliberate dazzling of third parties.

• Controlling of machines, moving objects or similar monitoring application without

additional control and safety installations.

• Aiming directly into the sun.

• Inadequate safeguards at the working site.

1.3 Limits of Use

Environment Suitable for use in an atmosphere appropriate for permanent human habitation: not

suitable for use in aggressive or explosive environments.

DANGER Local safety authorities and safety experts must be contacted before working in

hazardous areas, or close to electrical installations or similar situations by the person

in charge of the product.

1.4 Responsibilities

Manufacturer of

the product

Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as Leica Geosys-

tems, is responsible for supplying the product, including the user manual and original

accessories, in a safe condition.

Person responsible

for the product

The person responsible for the product has the following duties:

• To understand the safety instructions on the product and the instructions in the

user manual.

• To ensure that it is used in accordance with the instructions.

• To be familiar with local regulations relating to safety and accident prevention.

• To inform Leica Geosystems immediately if the product and the application

becomes unsafe.

• To ensure that the national laws, regulations and conditions for the operation of

e.g. radio transmitters or lasers are respected.

FlexLine plus, Safety Directions 10

1.5 Hazards of Use

CAUTION Watch out for erroneous measurement results if the product has been dropped or has

been misused, modified, stored for long periods or transported.

Precautions:

Periodically carry out test measurements and perform the field adjustments indicated

in the user manual, particularly after the product has been subjected to abnormal use

as well as before and after important measurements.

DANGER Because of the risk of electrocution, it is dangerous to use poles, levelling staffs and

extensions in the vicinity of electrical installations such as power cables or electrical

railways.

Precautions:

Keep at a safe distance from electrical installations. If it is essential to work in this

environment, first contact the safety authorities responsible for the electrical instal-

lations and follow their instructions.

CAUTION Be careful when pointing the product towards the sun, because the telescope func-

tions as a magnifying glass and can injure your eyes and/or cause damage inside the

product.

Precautions:

Do not point the product directly at the sun.

WARNING During dynamic applications, for example stakeout procedures there is a danger of

accidents occurring if the user does not pay attention to the environmental conditions

around, for example obstacles, excavations or traffic.

Precautions:

The person responsible for the product must make all users fully aware of the existing

dangers.

WARNING Inadequate securing of the working site can lead to dangerous situations, for example

in traffic, on building sites and at industrial installations.

Precautions:

Always ensure that the working site is adequately secured. Adhere to the regulations

governing safety, accident prevention and road traffic.

CAUTION If the accessories used with the product are not properly secured and the product is

subjected to mechanical shock, for example blows or falling, the product may be

damaged or people can sustain injury.

Precautions:

When setting up the product, make sure that the accessories are correctly adapted,

fitted, secured, and locked in position.

Avoid subjecting the product to mechanical stress.

WARNING If the product is used with accessories, for example masts, staffs, poles, you may

increase the risk of being struck by lightning.

Precautions:

Do not use the product in a thunderstorm.

Autres manuels pour FlexLine plus

Table des matières

Autres manuels Leica Instrument de mesure

Leica

Leica FlexLine TS10 Manuel utilisateur

Leica

Leica NA2 Manuel utilisateur

Leica

Leica DISTO D410 Mode d'emploi

Leica

Leica TS13 Manuel utilisateur

Leica

Leica DISTO A5 Manuel utilisateur

Leica

Leica RANGEMASTER CRF 800 Manuel utilisateur

Leica

Leica PIPER 100 Manuel utilisateur

Leica

Leica RANGEMASTER CRF 1600-B Manuel utilisateur

Leica

Leica RANGEMASTER 1200 scan Manuel utilisateur

Leica

Leica AT930 Manuel utilisateur

Leica

Leica TS12P Manuel utilisateur

Leica

Leica DNA03 Manuel utilisateur

Leica

Leica TS01 Manuel utilisateur

Leica

Leica AT500 Manuel utilisateur

Leica

Leica RANGEMASTER CRF PRO Manuel utilisateur

Leica

Leica TPS1200 series Manuel du produit

Leica

Leica DS2000 Manuel utilisateur

Leica

Leica BLK3D Manuel utilisateur

Leica

Leica TM30 Series Manuel utilisateur

Leica

Leica Viva TS16 Manuel utilisateur

Leica

Leica RANGEMASTER CRF 1200 Manuel utilisateur

Leica

Leica T105 Manuel utilisateur

Leica

Leica Sprinter 250M Manuel utilisateur

Leica

Leica Viva TS16 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur