Ledj LEDJ24 Manuel utilisateur
www.prolight.co.uk
LED 64 RGBA Can
(Order code: LEDJ24 -Black)
(Order code: LEDJ25 -Polished)
USER MANUAL
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
THIS UNIT ONLY ACCEPTS AN
INPUT VOLTAGE OF 240V
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
LEDJ LED RGBA Can Safety
LEDJ LED RGBA Can Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Do not expose to ammable sources or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
You should nd inside the LEDJ carton the following items:
1, LEDJ LED RGBA Can 2, Instruction manual
Technical Specications:
DMX channels: 7
400Hz icker free RGBA LEDs
Power supply: AC 240 ~ 50Hz
177 Ultra Bright 10mm LEDs (R: 30, G: 48, B: 54, A: 45)
Power Consumption: 25W
Beam angle: 25 degrees
Dimensions: 290 x 230 x 220mm
Weight: 2.0kgs
Operating modes: 1, Static Colour mode
2, Colour change mode
3, Colour Fade mode
4, Auto Run mode
5, Slave mode
6, LED mode
7, Sound active mode
8, DMX mode
LEDJ LED RGBA Can Technical specications
Overview:
1, DMX input
2, DMX output
3, LED display
4, Fuse (0.5A)
5, Mode selection button
6, Set up button
7, Function up button
8, Function down button
1
2
3
4
5
6
8
7
1, Static colour mode
Mode button - Press the “MODE” button under the LED display, to show “C000”, then press the
“ENTER” button to choose one of the static colours using the “UP” and “DOWN” buttons.
1, “C100” = R, 2, “C200” = G, 3, “C300” = B, 4, “C400” = A, 5, “CF00” = Strobe
Now press the “ENTER” button again and you can then select the output brightness using the
“UP” and “DOWN” buttons. The light output settings are from 00-99 (00 = off, 99 = full)
2, Colour change mode
Mode button - Press the MODE button until the LED display shows “JU00”, then press the
“ENTER” button to choose one of the colour changing modes using the “UP” and “DOWN” buttons.
1, “JU00” = RGBA (15 colours), 2, “JF00” = Strobe,
Now press the “ENTER” button again and you can then select the colour change speed using the
“UP” and “DOWN” buttons.
3, Colour fade mode
Mode button - Press the MODE button until the LED display shows “F000”, then press the
“ENTER” button to choose one of the colour fading modes using the “UP” and “DOWN” buttons.
1, “FA00” = RGBA (15 colours), 2, “FF00” = Strobe,
Now press the “ENTER” button again and you can then select the colour fade speed using the
“UP” and “DOWN” buttons.
4, Auto Run mode
Mode button - Press the MODE button until the LED display shows “AUTO”, the unit will now run
through it’s built-in programmes.
5, Slave mode
Link the units together using a 3-pin DMX cable, then press the MODE button to select one of the
above modes. On the Slave units press the mode button until the LED display shows “SLAV”. The
Slave units will then follow in sequence with the Master unit.
6, LED mode - Use this mode to switch the LED display On and Off
7, Sound active mode
Mode button - Press the MODE button until the LED display shows “SU00”, then press the
“ENTER” button to set the desired sensitivity level using the “UP” and “DOWN” buttons.
The sound sensitivity levels are from 00-99 (00 = low, 99 = high)
8), DMX Addressing mode
To access the DMX address mode, press the MODE button until the LED display shows “A001”,
then press the “ENTER” button and set the rst digit in the DMX address using the “UP” and
“DOWN” buttons. Now repeat this step to set the second and third digits for the desired DMX
address setting. Follow the DMX channel assignment and function table overleaf.
Note: The speed settings for operation modes 2 and 3 are from 00-99 (00 = slow, 99 = fast)
The strobe speed settings for operation modes 1, 2 and 3 are from 00-99 (00 = slow, 99 = fast)
LEDJ LED RGBA Can Operation
7 Channel DMX chart
LEDJ LED RGBA Can DMX Chart
Channel
1
2
3
4
5
6
7
Value
000-255
000-255
000-255
000-255
000-255
000-255
0-4
5-80
81-150
151-255
Function
Master dimmer
Strobe
Red (0 - 100%)
Green (0-100%)
Blue (0-100%)
Amber (0-100%)
No function
Colour Macro
Colour change
Colour fade
www.prolight.co.uk
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Ledj Équipement d'éclairage
Ledj
Ledj LEDJ377 Manuel utilisateur
Ledj
Ledj STAGE BAR 16 Manuel utilisateur
Ledj
Ledj STRATOS SPOT Manuel utilisateur
Ledj
Ledj LEDJ251 Manuel utilisateur
Ledj
Ledj STRATOS Manuel utilisateur
Ledj
Ledj Spectra Q40 MKII Manuel utilisateur
Ledj
Ledj STAR18 Manuel utilisateur
Ledj
Ledj LEDJ472 Manuel utilisateur
Ledj
Ledj Stage Par CZ200 3200K Manuel utilisateur
Ledj
Ledj Pixel Storm 6 Tri Batten Manuel utilisateur
Ledj
Ledj LEDJ266 Manuel utilisateur
Ledj
Ledj PERFORMER 54 RGBW LEDJ250 Manuel utilisateur
Ledj
Ledj LEDJ283A Manuel utilisateur
Ledj
Ledj BlockBuster 6 Manuel utilisateur
Ledj
Ledj LED-56 Manuel utilisateur
Ledj
Ledj Xterior Wash Tri Manuel utilisateur
Ledj
Ledj Aspect XL LEDJ302 Manuel utilisateur
Ledj
Ledj Slimline 12Q5 Series Manuel utilisateur
Ledj
Ledj STAGE PAR 64 Manuel utilisateur
Ledj
Ledj LEDJ254 Manuel utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
