Larson Electronics EPSW-1PH-20 Manuel utilisateur

EPSW-1PH-20

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1of 2

Single Phase Explosion Proof Switch

Non Fused - 2-Pole - 20 Amps - Lock Out / Tag Out

Instruction Manual

Thank you for your purchase of the Larson Electronics EPSW-1PH-20.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

WARNING

TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL

APPLICABLEELECTRICAL CODES.

TO AVOIDELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

IMPORTANT SAFEGUARDS; READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

1) Do not use this equipment other than the intended use as specified on the equipment nameplate.

2) Turn OFF the supplying circuit before beginning installation or performing any maintenance.

3) Service should be performed by qualified service personnel.

4) All installations must comply with the applicable local and/or National Electrical Code.

(Note: In the orientation of the enclosure (box & cover), the “TOP” is considered to be at the location of the cast-in part

numbers.)

The EPSW-1PH-20 from Larson Electronics is a 480V AC explosion proof switch with a 20 amp and 5 horsepower

rating. This explosion proof switch is rated explosion proof for Class I Divisions 1 & 2 Groups B, C and D, Class II

Divisions 1 & 2 Groups E, F and G, and Class III environments. This unit is available with multiple hub options including

1" and 3/4" NPT hub sizes. The EPSW-1PH-20 can be used in hazardous work locations both indoors and outdoors and

can also be used in areas where frequent washdowns, heavy rain or water spray occur.

EPSW-1PH-20

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2of 2

WIRING

Standard pigtail(flying leads) wiring

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 120V, 208V, 230V, 480V, or

600V AC.

Warning: Check product label for correct input voltage!

Attach supply line wires to the appropriate light fixture wires as shown

in thediagram 

Secure each pair of wires according to the diagram. Utilize ajunction box or

similar device and takeprecautionary steps for weatherproofing all

connectionsif installed in alocation where water may come in contact with the

unit. Ensurethe unit is properly grounded and that wiring is done according to

all local and national electrical/building codes.

•Disconnect power running to the unit and be sure the fixture iscool to the touch.

•Use a non-abrasive cleaning solution to clean the unit.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EPSW-1PH-20 is designed to provide years of reliable performance. Should the need for replacement parts arise,

please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

MAINTENANCE

There are no serviceable parts inside the fixture. However, itis good practice to routinely clean and check the

fixture for proper function.

INSTALLATION:

1) Install non-fused disconnect of your choice on din rail and align per instructions on page 3.

2) Install the two end blocks (provided) onto the din rail. Secure the blocks permanently on both sides of disconnect

by using a screw driver and tightening the recessed screws.

3) Cut “square shaft” provided, to the over-all length dimension shown in the chart on page 2, for the specific device

being used. (NOTE: smooth out the cut edge of the shaft)

4) Insert “square shaft bracket” into disconnect device interface opening per the orientation shown in the

picture on page 2.

5) Insert thecut shaft thru the square hole in the bracket, allowing it to rest at the bottom of the device interface

opening and in the orientation shown in the picture on page 2.

6) Terminate incoming cables to the line and load side of disconnect (field installation only).

7) Assemble cover on box making certain that the cross pinin the square shaft is engaged in the slot of the

operator in cover.

8) Tighten cover bolts.

Table des matières

Autres manuels Larson Electronics Changer

Larson Electronics

Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1 Manuel utilisateur

Larson Electronics

Larson Electronics EXP-RT-3PH-MIN.5-208V Manuel utilisateur

Larson Electronics

Larson Electronics EPS-1XPB-1XPL-M1-24V Manuel utilisateur

Larson Electronics

Larson Electronics EPCS-PL-2X-RG Manuel utilisateur

Larson Electronics

Larson Electronics MPD-DS-WML-NFDS Series Manuel utilisateur

Larson Electronics

Larson Electronics EPS-FS-B-2PSW Manuel utilisateur

Larson Electronics

Larson Electronics LED-ILS Manuel utilisateur

Larson Electronics

Larson Electronics VPLHL-7WLED-50-NP Manuel utilisateur

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V Manuel utilisateur

Larson Electronics

Larson Electronics EPSW-3PH-20 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-10HP-3PST Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-MS-SPDT Manuel utilisateur

Larson Electronics

Larson Electronics GAU-125V-20A-P Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-2XC-M2-YR Manuel utilisateur

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH Manuel utilisateur

Larson Electronics

Larson Electronics EPNFDS-MTS-200A-3P Manuel utilisateur

Larson Electronics

Larson Electronics LM HZ-EW-SP1097-HV Series Manuel utilisateur

Larson Electronics

Larson Electronics EPS-3PSW-MMS Manuel utilisateur

Larson Electronics

Larson Electronics EPSW-30A-WP Manuel utilisateur

Larson Electronics

Larson Electronics GAU-SW-4P-WW-24V Manuel utilisateur

Larson Electronics

Larson Electronics EXHL-TRN-LE1 Series Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-V4 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB20 Manuel utilisateur

Larson Electronics

Larson Electronics MPD-DS-WM-FDS Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur