Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1 Manuel utilisateur

EPCS-PB10-2XMPB-2PS-N4X-M1

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 3

10A Explosion Proof Push Control Station

Class I, II, III - (2) Momentary PBs, (1) 2-Pos Switch - Labels

Instruction Manual

Thank you for your purchase of the Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE EPCS-PB10-2XMPB-2PS-N4X-M1 MUST BE WIRED IN ACCORDANCE WITH NATIONAL

ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

The Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1 Explosion Proof Control Station is suitable for use in Class I, II and III rated

combustible sites. This weatherproof unit contains three operators: (2) momentary push buttons and (1) 2-position switch. The operators

are labeled for proper use. Protected by a copper-free aluminum enclosure, the control device is offered with 1/2" or 3/4" hub size.

WIRING

Standard pigtail(flying leads) wiring

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 600V.

Warning: Check product label for correct input voltage!

Attach supply line wires to the appropriate light fixture wires as shown

in thediagram 

Secure each pair of wires according to the diagram. Utilize a junction box or

similar device and take precautionary steps for weatherproofing all

connections if installed in a location where water may come in contact with the

unit. Ensure the unit is properly grounded and that wiring is done according to

all local and national electrical/building codes.

EPCS-PB10-2XMPB-2PS-N4X-M1

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 3

Ratings/Approvals

Class I, Divisions 1&2 Groups C,D

Class II, Division 1, Groups E, F, G

Class III

NEMA 3R, 4, 4X, 7 (C,D) 9 (E,F,G)

NRTL Listed to UL 508A, UL 1203

NRTL Listed to CSA C22.2 No 14, 25, 30

CAUTION: Before installing, make sure you are compliant with area classifications, as

failure to do so may result in bodily injury, death and property damage. Do not attempt

installation until you are familiar with the following procedures. All installation must comply

with the applicable Electrical Code(s).

Make sure that the circuit is de-energized before starting installation or maintenance. Verify

that the installation is grounded. Failure to ground will create electrical shock hazards,

which can cause serious injury and or death.

MOUNTING INSTRUCTIONS

To install the product correctly, follow the steps below:

PUSHBUTTONS:

1. Disconnect the contact block from the assembly by sliding the cage locking tab

clockwise.

2. Remove the nut and protective sleeve from the threaded body.

3. Place the legend plate when used under the knob, or attach to the enclosure, if

applicable.

4. Make sure the operator threads and surface being attached to are clean and free of

debris. Screw the pushbutton assembly into the enclosures 3/4” NPSM or M22x1,5

threaded entry and torque 3 N-m to 6 N-m (27 in.-lbs. to 53 in.-lbs.). Ensure legend

plate is held in place to prevent rotation, if applicable.

5. Install the nut onto the assembly threaded body and torque to 2 N-m (18 in.-lbs.) with an

appropriate tool.

6. Installing the contact block to the assembly:

a. With the cage locking tab held in the clockwise position, align the assembly channel

with the locking cage ID tabs on the contact block and slide the block onto the

assembly.

b. Move the cage tab counterclockwise to lock switch in place.

c. Verify orientation of block is such that control wires and certification tag won't be

directed into flame path of cover/body.

After performing the connections described above, the product can be safely used, and the

ingress of protection is assured.

EPCS-PB10-2XMPB-2PS-N4X-M1

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 3of 3

MAINTENANCE

There are no serviceable parts inside the fixture. However, itis good practice to routinely clean and check the

fixture for proper function.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EPCS-PB10-2XMPB-2PS-N4X-M1 is designed to provide years of reliable performance. Should the need for

replacement parts arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Table des matières

Autres manuels Larson Electronics Changer

Larson Electronics

Larson Electronics EPCS-PB10-1XMPB-3PSW Manuel utilisateur

Larson Electronics

Larson Electronics EXHL-TRN-LE1 Series Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-V4 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-1XPB-1XPL-M1-24V Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB20 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V Manuel utilisateur

Larson Electronics

Larson Electronics EXP-RT-3PH-MIN.5-208V Manuel utilisateur

Larson Electronics

Larson Electronics EPCS-PL-2X-RG Manuel utilisateur

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH Manuel utilisateur

Larson Electronics

Larson Electronics EPS-FS-B-2PSW Manuel utilisateur

Larson Electronics

Larson Electronics EPO-20A Manuel utilisateur

Larson Electronics

Larson Electronics MPD-DS-WML-NFDS Series Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-MS-SPDT Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-2XC-M2-YR Manuel utilisateur

Larson Electronics

Larson Electronics EPS-25A-3W Manuel utilisateur

Larson Electronics

Larson Electronics MPD-DS-WM-FDS Series Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-GRN-2XC Manuel utilisateur

Larson Electronics

Larson Electronics EPS-2XPB-SG-DPMS Manuel utilisateur

Larson Electronics

Larson Electronics C1D2 Manuel utilisateur

Larson Electronics

Larson Electronics EPSW-1PH-20 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-2XPB-SG-600V-LKC Manuel utilisateur

Larson Electronics

Larson Electronics EPS-SW1-ESTP Manuel utilisateur

Larson Electronics

Larson Electronics GAU-SW-4P-WW-24V Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur