Larson Electronics EPS-2XPB-SG-600V-LKC Manuel utilisateur

EPS-2XPB-SG-600V-LKC

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 3

Explosion Proof Push Button 600V Stop/Start Switch

Class I, II, III - Motor Starter Switch - (2) Lockout

Instruction Manual

Thank you for your purchase of the Larson Electronics EPS-2XPB-SG-600V-LKC.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE EPS-2XPB-SG-600V-LKC MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

WARNING

TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL

APPLICABLEELECTRICAL CODES.

TO AVOIDELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

The EPS-2XPB-SG-600V-LKC from Larson Electronics is a 600V Explosion Proof Push Button Stop/Start Switch that is

Class I, Divisions 1 & 2 and Class II, Divisions 1 & 2 rated for hazardous locations. This explosion proof switch provides

manual starting and stopping of small AC and DC motors. Operators may access two stainless steel lockouts for the push

buttons.

EPS-2XPB-SG-600V-LKC

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 3

INSTALLATION

1. Mount the back box by means of mounting lugs. Install conduit nipple and sealing fittings, to be installed on each

conduit entrance or exit to the enclosure back box in Class I and Class II areas. Thread conduit into sealing fitting

(Note: For Class I areas, the conduit should engage [5] full threads.)

2. The conduit threads should be lubricated with a non-electrical insulating lubricant or pipe joint compound that will

not promote corrosion or chemically attack aluminum.

3. After conduit system has been properly installed, pull the wires and make electrical connections as required. The

electrical circuits and ground continuity should be checked with an instrument approved for the area. Notice:

Connect only copper wire to this device.

4. All conduits entering or leaving the enclosure must be sealed within 18” of the enclosure with listed sealing

fittings. Caution must be taken during installation to be sure that the ground flange flame joints of the cover and

box are not scratched, nicked, or damaged. Before assembly of the cover to the box, the mating ground surfaces

of both the box and cover should be wiped clean to assure that the ground flame joint will be free of all foreign

particles such as lint, dust or dirt.

5. After tightly bolting the cover assembly/assemblies to the enclosure, all box to cover flame joints should be

checked with a 0.0015” thick feeler gauge such that the gauge will not enter the flame path more than 1/8” at any

point.

WIRING

Standard pigtail(flying leads) wiring

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 600V.

Warning: Check product label for correct input voltage!

Attach supply line wires to the appropriate light fixture wires as shown

in thediagram 

Secure each pair of wires according to the diagram. Utilize a junction box or

similar device and take precautionary steps for weatherproofing all

connections if installed in a location where water may come in contact with the

unit. Ensure the unit is properly grounded and that wiring is done according to

all local and national electrical/building codes.

MAINTENANCE

All moving shafts should be lubricated

occasionally to prevent binding. Only use a

lubricant which is suitable for use with

aluminum or stainless steel. If devices are

to be installed in corrosive areas which will

attack aluminum alloys containing less than

0.4% copper (boxes and covers) and 303

stainless steel (mostly shafts), the device

should be suitably protected from the

corrosive material.

CAUTION: To prevent ignition of

hazardous atmospheres, disconnect from

the supply circuits before opening the

enclosure; keep tightly closed while circuits

are energized.

EPS-2XPB-SG-600V-LKC

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

3of 3

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EPS-2XPB-SG-600V-LKC is designed to provide years of reliable performance. Should the need for replacement

parts arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Table des matières

Autres manuels Larson Electronics Changer

Larson Electronics

Larson Electronics EXHL-TRN-LE1 Series Manuel utilisateur

Larson Electronics

Larson Electronics EPS-SW1-ESTP Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-N4X-V3 Manuel utilisateur

Larson Electronics

Larson Electronics EPL-SW Series Manuel utilisateur

Larson Electronics

Larson Electronics EPO-20A Manuel utilisateur

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V Manuel utilisateur

Larson Electronics

Larson Electronics EPSW-3PH-20 Manuel utilisateur

Larson Electronics

Larson Electronics GAU-SW-4P-WW-24V Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-2XC-M2-YR Manuel utilisateur

Larson Electronics

Larson Electronics EXP-EL-CSS-250A-R1-NO Manuel utilisateur

Larson Electronics

Larson Electronics EPSW-1PH-20 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-2XPB-SG-DPMS Manuel utilisateur

Larson Electronics

Larson Electronics EPNFDS-MTS-200A-3P Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-V4 Manuel utilisateur

Larson Electronics

Larson Electronics MPD-DS-WM-FDS Series Manuel utilisateur

Larson Electronics

Larson Electronics LED-ILS Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB20 Manuel utilisateur

Larson Electronics

Larson Electronics EPS-1XPB-1XPL-M1-24V Manuel utilisateur

Larson Electronics

Larson Electronics MPD-DS-WML-NFDS Series Manuel utilisateur

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH Manuel utilisateur

Larson Electronics

Larson Electronics EPS-3PSW-MMS Manuel utilisateur

Larson Electronics

Larson Electronics EPS-PB10-GRN-2XC Manuel utilisateur

Larson Electronics

Larson Electronics EPCS-PB10-1XMPB-3PSW Manuel utilisateur

Larson Electronics

Larson Electronics EPS-25A Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur