Larson Electronics GL-4600-XD Manuel

24 Volt Visible/Infrared LED Remote

Control Spotlight –Light Only

INSTRUCTION GUIDE

Part# GL-4600-XD

Congratulations

You are now the owner of one of the ﬁnest remote control searchlights available today. Thank you for

letting Larson Electronics assist you in your lighting application needs. We're proud of our products and

the technology that we've developed to ensure our customers the most durable, versatile and powerful

searchlights in the lighting industry.

Please read these instructions before using your new Remote Control Spotlight from Larson Electronics.

The GL-4600 is a 1-Speed Searchlight with

Directional Flexibility which gives the operator a full

360° horizontal rotation and a 180° vertical tilt with

fingertip control. The GL-4600 provides superior light

penetration with the new LED/PVEX lens technology.

MOUNTING INSTRUCTIONS

Light Unit/Permanent Mount

Determine the location for the light on your vehicle or

boat. Remove the mounting plate from the light.

Center the mounting plate. Mark the hole locations

for the four mounting screws and drill a pilot hole for

each with 1/8 inch bit. Fasten the stainless steel

mounting plate with the 3 #10 –16x3/4 type AB

cross recessed pan head tapping screws. Drill a 1

1/4” hole in the center of the mounting plate opening

to accommodate the wiring harness and connector.

Attach the connector that is affixed to the underside

of the light to the corresponding connector on the

wiring harness. Position the connection point

beneath the mounting surface, and apply silicone

sealant around wire to seal the drilled opening. Place

the light over the mounting plate. Install the set

screws (provided) and tighten.

Light Unit/Magnetic Mount

Select the best location on your vehicle for the

magnetic mount Stryker. Make sure the metal area

under the magnetic base is flat and clean to ensure a

strong bond. Route the power cord into the vehicle

through a door frame and connect to power outlet.

The magnetic mount GL-4600-M should be removed

from vehicle’s exterior while traveling at excessive

speeds and in strong wind conditions.

Dash Control/Permanent Mount

Determine the appropriate location for the dash

mount control and create an opening to

accommodate the board on the rear of the remote.

Affix the control to the dash with four screws. The

words should be facing upright and should be

situated accordingly. All wiring should be undertaken

with power removed from the system. First, attach

the connector that is affixed to the control to the

corresponding connector on the wiring harness.

Next, join the leads at the remote to 23-32V DC

power with appropriate automotive wire attachments;

the wire with (+) is the positive lead and the opposite

black wire is the negative lead--the unit is polarity

sensitive and care must be taken to observe this. As

a safety feature, the power switch is backlit to

indicate bulb illumination. Each spotlight needs to be

wired on a single dedicated circuit and the power

fused at 5 amps. With the power connected, your

light is ready for operation.

OPERATION OF GL-4600

1.Using the remote control, turn on the light by

moving the on/off switch.

2.With the joystick on the dash control, rotate your

light to the desired location. Movement speed

starts off slow and increases speed as the joystick

is held down.

3.Position the dial to use the desired light. WHITE

indicates the visible white LED light. IR indicates

infrared LED.

4.Move the power switch ON to power on the

selected light.

5.Press the HOME button to return the GL-4600

back to its original home position.

USAGE:

» This light is intended for off-road and utility use only

» This light is intended to be mounted outside the

vehicle while in use

» This light may only be disassembled and repaired

by an authorized representative

MISUSE:

» This light is not approved for road or highway use

» This light is not approved for underwater use

» This light is not approved for inverted mounting

» This light is not approved for use inside a vehicle or

enclosure and power should be disconnected prior to

placing the light in such circumstance

» This light may be damaged if operated in icing

conditions

» This light may only be dismantled by an authorized

Larson Electronics representative.

» Any violation of the above referenced misuses

will be considered grounds for warranty refusal

IMPORTANT SAFETY INFORMATION

This symbol is to alert you to important operating

or servicing instructions that appear in your

instructions.

Always follow basic safety

precautions when using

this product to reduce the

risk of injury, fire or electric shock.

This light is for off road and utility use only. It

is not designed for road use as a driving light.

The GL-4600 complies with Part. 15.105 of the

FCC Rules. This equipment has been tested and

found to comply with the limits for a Class B

digital device. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment

and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced

radio/TV technician for help.

FCC RULE Part. 15.21 - Changes or

modiﬁcations made by the user not expressly

approved by Larson Electronics, LLC. for

compliance could void the user’s authority to

operate the equipment.

PARTS / ACCESSORIES

GL-4600 parts and accessories may be

purchased through Larson Electronics.

Should further information not covered by these

instructions be required, please contact Larson

Electronics at 1-800-369-6671 or

sales@larsonelectronics.com for further assistance.

Please visit LarsonElectronics.com for Warranty

and Return information.

LARSON ELECTRONICS, LLC

9419 E US-HWY 175

KEMP, TX 75143

800.369.6671 | 903.498.3363

www.larsonelectronics.com

sales@larsonelectronics.com

Autres manuels Larson Electronics Mettre en lumière

Larson Electronics

Larson Electronics PTB-1 Manuel utilisateur

Larson Electronics

Larson Electronics GL-8130-M Manuel utilisateur

Larson Electronics

Larson Electronics GL-3110-S-12-E Manuel

Larson Electronics

Larson Electronics LED3W-LT-IR Manuel utilisateur

Larson Electronics

Larson Electronics RML-8 Manuel utilisateur

Larson Electronics

Larson Electronics Golight 51674 Manuel

Larson Electronics

Larson Electronics RCL700 Manuel d'exploitation et d'entretien

Larson Electronics

Larson Electronics GL-30514-S-E Manuel

Larson Electronics

Larson Electronics GL-2000-S-E Manuel

Larson Electronics

Larson Electronics 2000-M Manuel

Larson Electronics

Larson Electronics LEDWL 1227 Series Manuel

Larson Electronics

Larson Electronics HUL-P10WR-DM-ILS-1227 Manuel utilisateur

Larson Electronics

Larson Electronics HAL-RA-48-6L-LED Manuel utilisateur

Larson Electronics

Larson Electronics GAU-LTL-500W-LED-IR Manuel utilisateur

Larson Electronics

Larson Electronics HL-85-HID Manuel utilisateur

Larson Electronics

Larson Electronics GVP-48-2L-LED-D-V2 Manuel utilisateur

Larson Electronics

Larson Electronics GL-3100-S-12-E Manuel

Larson Electronics

Larson Electronics HL-85-3W1-IR Manuel utilisateur

Larson Electronics

Larson Electronics RL-20 Manuel utilisateur

Larson Electronics

Larson Electronics Golight 51494 Manuel

Larson Electronics

Larson Electronics GL-9100H-S Manuel

Larson Electronics

Larson Electronics Golight Radioray 2000 Manuel

Larson Electronics

Larson Electronics APM-GL20004 Manuel utilisateur

Larson Electronics

Larson Electronics GL-3610-S-E Manuel

Manuels Mettre en lumière populaires d'autres marques

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuel utilisateur

LIVARNO home

LIVARNO home 375304 2101 Instructions originales

Cameo

Cameo CLQS40WW Manuel utilisateur

Leviton

Leviton Ellipsoid 5/50 Manuel utilisateur

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuel utilisateur

Vector

Vector SL3AKV Manuel utilisateur

Quantum

Quantum Q262 Manuel d'exploitation

Philips

Philips Vari-lite VL3015LT Manuel utilisateur

EUROSPOT

EUROSPOT C51 Manuel utilisateur

DTS

DTS MINI BRICK ARC Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuel

ACME

ACME LED-MS350B Manuel utilisateur

EuroLite

EuroLite Akku flat light 1 Manuel utilisateur

Commercial Electric

Commercial Electric SPTM-1401 Manuel utilisateur

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuel utilisateur

Teknik

Teknik FLEXI Manuel utilisateur

Craftsman

Craftsman CMXLSB10 Manuel utilisateur

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuel utilisateur