Larson Electronics HID-A1830-WA Manuel utilisateur

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

HID-A1830-WA

H.I.D. SYSTEM WARNING

Do not stare directly into the light or shine directly into the eyes of another person as this may

cause temporary loss of vision.

Do not let water enter the case, while the light is both weather and water resistant, it is not

designed to be submersible.

Never disassemble the light as all parts must be factory serviced to insure proper operation.

The auxiliary light is to be mounted on the vehicle only in a vertical, bottom-mounting or in a

suspended position.

Do not allow objects or skin to contact a hot lens because of burn risk.

The auxiliary light must not adversely affect the performance of low beam, high beam, engine

cooling or the driver’s view.

Before working on the auxiliary Xenon light: disconnect the negative terminal (-) from the

battery. Make sure that the vehicle’s electrical system is de-energized.

Installation and lamp change may only be carried out by qualified or properly trained persons.

Use the supplied wire harness for electrical installation.

Before switching on the auxiliary light, the lens cover must be removed!

NOTICE

Completely read all instructions before installing.

Consult your local or state regulatory agency regarding the use of auxiliary lighting.

The placement of auxiliary lighting should not restrict airflow to the radiator or block

headlamps, turn signals or parking lights.

INSTALLING THE LIGHT

1. Disconnect the negative terminal (-) from the battery and wrap with electrical tape to prevent

contact.

2. Select a suitable attachment location and then mark and drill the 11 mm diameter hole for

mounting.

CAUTION: Consult your vehicle owner’s manual or manufacturer regarding location of airbag or

other sensors near the mounting location.

3. Fit the additional headlamp with washer, spring washer, and nut.

WIRING HARNESS INSTALLATION

The wiring harness is pre-assembled and fully insulated and sleeved.

1. Lay out wiring so that all connections (battery, relay, switch, & lights) will have more than

sufficient length.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

2. Find a suitable location to mount the relay on the battery side of the engine compartment.

Make sure the mounting location is not exposed to water spray, excessive heat, or moving parts.

3. Attach both power supply wires (red) to the positive (+) battery terminal.

4. Connect the ground wire (black) to the vehicle chassis or the negative (-) battery terminal,

connect the wiring to switch.

5. Locate an unused grommet on the firewall. If one cannot be found, drill a ½” hole with no

obstructions on either side and away from moving parts and other wiring.

6. Feed the switch connector through the firewall and into the vehicle interior to the switch

mounting location.

7. Select a suitable mounting location for the switch such as the dashboard or center console.

8. Clean and dry both the mounting surface and the back of the switch and use double sided

adhesive pad to secure.

9. Plug the switch connector into the wiring harness and secure all loose wiring to ensure safe

vehicle operation.

10. Feed the auxiliary light wiring to each light with the shorter length going to the light on the

battery side.

11. Plug the power supply socket to each light and attach the ground wire (black) to the vehicle

chassis.

OPTIONAL LOW/HIGH BEAM CONNECTION

Some states require auxiliary lighting to be connected to low/high beam wiring so that they may only be

used when your headlights are on. An additional benefit is to prevent battery draining in case the

headlights are accidentally left on. If you choose not to do this you may connect directly to the positive

terminal and your auxiliary lights will operate at any time using the switch.

Feed the single (red) wire to the positive (+) low or high beam wire and attach using the blue

wiretap connector.

TURNING ON AND TESTING OPERATION

1. Remove electrical tape from the negative (-) terminal and re-connect onto the battery.

2. Turn on ignition switch and activate the auxiliary light switch.

NOTE: If you attached the optional connector to the low or high beam you will need to turn on your

headlamps to that position before the auxiliary lamps will light.

If lamps do not light, check fuse(s) and all wiring connections.

Use wire ties to secure all loose wiring in the engine compartment, making sure all wiring is away from

moving parts and excessive heat.

CAUTION: IT IS STRONGLY RECOMMENDED THAT ANTI-SEIZE BE USED ON ALL MOUNTING

HARDWARE.

Table des matières

Autres manuels Larson Electronics Mettre en lumière

Larson Electronics

Larson Electronics LED10W-6RT-LT Manuel utilisateur

Larson Electronics

Larson Electronics HL-85-CPR-MS Manuel utilisateur

Larson Electronics

Larson Electronics Golight 51494 Manuel

Larson Electronics

Larson Electronics GL-3110-S-12-E Manuel

Larson Electronics

Larson Electronics LED10W-1SCB Manuel utilisateur

Larson Electronics

Larson Electronics LE Series Manuel utilisateur

Larson Electronics

Larson Electronics HUL-P10WR-DM-ILS-1227 Manuel utilisateur

Larson Electronics

Larson Electronics GL-9901 Manuel

Larson Electronics

Larson Electronics GL-3100-S-12-E Manuel

Larson Electronics

Larson Electronics GL-9100H-S Manuel

Larson Electronics

Larson Electronics EXPRA-06R-LED Manuel utilisateur

Larson Electronics

Larson Electronics GL-3610-S-E Manuel

Larson Electronics

Larson Electronics IL-LED-27R Manuel utilisateur

Larson Electronics

Larson Electronics LED10W-LT Manuel utilisateur

Larson Electronics

Larson Electronics HAL-RA-48-6L-LED Manuel utilisateur

Larson Electronics

Larson Electronics Golight GL-2 GT Series Manuel

Larson Electronics

Larson Electronics RL-85-3W1 Manuel utilisateur

Larson Electronics

Larson Electronics HL-85-LED-CPR-NC Manuel utilisateur

Larson Electronics

Larson Electronics GVP-48-2L-LED-D-V2 Manuel utilisateur

Larson Electronics

Larson Electronics Golight Radioray 2000 Manuel

Larson Electronics

Larson Electronics GL-30514-S-E Manuel

Larson Electronics

Larson Electronics GL-2100-E-F Manuel

Larson Electronics

Larson Electronics PML-90LED-DP-120 Manuel utilisateur

Larson Electronics

Larson Electronics MUL-30-LED Manuel utilisateur

Manuels Mettre en lumière populaires d'autres marques

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuel utilisateur

LIVARNO home

LIVARNO home 375304 2101 Instructions originales

Cameo

Cameo CLQS40WW Manuel utilisateur

Leviton

Leviton Ellipsoid 5/50 Manuel utilisateur

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuel utilisateur

Vector

Vector SL3AKV Manuel utilisateur

Quantum

Quantum Q262 Manuel d'exploitation

Philips

Philips Vari-lite VL3015LT Manuel utilisateur

EUROSPOT

EUROSPOT C51 Manuel utilisateur

DTS

DTS MINI BRICK ARC Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuel

ACME

ACME LED-MS350B Manuel utilisateur

EuroLite

EuroLite Akku flat light 1 Manuel utilisateur

Commercial Electric

Commercial Electric SPTM-1401 Manuel utilisateur

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuel utilisateur

Teknik

Teknik FLEXI Manuel utilisateur

Craftsman

Craftsman CMXLSB10 Manuel utilisateur

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuel utilisateur