La Crosse Technology 513-1417v6 Manuel utilisateur
SET UP GUIDE
MODEL: 513-1417v6
ATOMIC DIGITAL WALL CLOCK
WITH INDOOR/OUTDOOR TEMPERATURE & MOON PHASE
1. Insert 2-AA batteries into your Outdoor Sensor.
2. Insert 2-AA batteries Into your Clock.
3. Enter the Settings Menu to adjust your time and date.
4. Once the sensor is reading to your clock, place the sensor outside in a
shaded location. View our sensor mounting video here:
bit.ly/th_sensor_mounting
2
POWER UP
Atomic Clock
513-1417v6
Outdoor Sensor
TX141-Bv4
Atomic Time Signal
AA
AA
AA
AA
• The clock will search for the Atomic Time Signal at power up and at UTC
7:00, 8:00, 9:00, 10:00, and 11:00.
• The Atomic Time Signal Icon will flash while searching and be solid
when it has connected.
• From the normal time display, press the SET button to manually start or
stop a search for the WWVB time signal. For information about WWVB
visit: bit.ly/atomic_time.
3
SETTINGS MENU
Language: Whichever language is selected, the following instructions and
weekday will be presented in that language.
Atomic Off: When Atomic O is selected your next setting will be the Hour.
Weekday: Your weekday display will adjust automatically once you
have your Year, Month, and Date settings set correctly.
1. Hold the SET button until the display changes to enter the Settings
Menu. Press and release the + or - buttons to adjust values. Hold to
adjust quickly.
2. Press and release the SET button to confirm values and move to the
next setting.
3. Press and release the SNOOZE button at any time to exit.
Settings Menu Order:
• Language English | Spanish
• Beep ON | OFF
• Atomic ON | OFF
• DST ON | OFF (Daylight Saving Time)
• Time Zone
• Hour
• Minutes
• Year
• Month
• Date
• Fahrenheit | Celsius
TIME ZONES
Atlantic: ZONE-AST
Eastern: ZONE-EST
Central: ZONE-CST
Mountain: ZONE- MST
Pacific: ZONE-PST
Alaska: ZONE-AKT
Hawaii: ZONE-HAT
4
Silence a Sounding Alarm: Press any button except SNOOZE to silence the
alarm for 24 hours.
Activate/Deactivate Alarm:
• Press and release the ALARM button to view the Alarm Time. Press
and release again to activate or deactivate the alarm.
• The Alarm Icon will show when alarm is active.
Snooze: When the alarm is active, press the SNOOZE button to silence
the alarm for 10 minutes. The alarm Icon will flash while snoozing.
Note: The alarm will sound with increasing frequency for two minutes,
then shut off automatically if not silenced.
Set Alarm:
1. Hold the ALARM button to enter alarm setting mode. ALARM will show
and the hour will flash. Press and release the + or - buttons to choose the
hour.
2. Press and release the ALARM to confirm and move to the minutes. The
minutes will flash. Press and release the + or - buttons to choose the
minutes.
3. Press and release the ALARM button to confirm and exit.
4. Press and release the SNOOZE button at any time to exit.
TIME ALARM
MOON PHASE
The moon phase is based on the Lunar Calendar and the year, month, and date
settings.
Full Moon
New Moon
Small Waning
Crescent
Large Waxing
Gibbous
Large Waning
Crescent
Small Waxing
Gibbous
Last Quarter
First Quarter
Small Waning
Gibbous
Large Waxing
Crescent
Large Waning
Gibbous
Small Waxing
Crescent
HI / LO TEMPERATURE
High and Low Temperature Records will automatically reset daily at
midnight.
• Press and release the + (PLUS) button once to view High Indoor and
Outdoor Temperatures.
• Press and release the + (PLUS) button twice to view Low Indoor and
Outdoor Temperatures.
• Press again to return to normal time display.
Manually Reset Records:
• Hold the + (PLUS) button to manuall reset the High and Low records.
5
6
TEMPERATURE TREND ARROWS
Both the Indoor and Outdoor Temperature values have Trend Arrows to
indicate changes (1°C / 2°F or more) over the past three hour period.
Temperature has risen over the past three hours.
Temperature has been steady over the past three hours.
Temperature has fallen over the past three hours.
SEARCH FOR OUTDOOR SENSOR
If you are seeing NO for your outdoor readings, please try the
following steps:
1. Hold the - (MINUS) button to search for your outdoor sensor. The
Reception Indicator will begin to animate.
2. If after 3 minutes the sensor still isn’t connected, bring the sensor inside
next to the display and remove power from both the sensor and clock.
3. Press any button on the clock 20 times and leave the parts sit for a few
moments with the power o.
4. Install a new set of alkaline batteries into the sensor, then into your clock.
For additional help visit: bit.ly/basic_restart
LOW BATTERY INDICATOR
Low Battery Icon by Outdoor Temperature, replace batteries in the
Outdoor Sensor.
Low Battery Icon by the Time, replace batteries in the Clock.
7
Designed in La Crosse, Wisconsin •Made in China •Printed in China •DC 061223
CA WARNING:
This product can expose you to chemicals including acrylonitrile, butadiene, and styrene,
which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information, go to: www.P65Warnings.ca.gov
If you require additional assistance, get in touch with our
friendly customer support team based in La Crosse, WI.
Self Help: bit.ly/513-1417v6_support
Online: bit.ly/contact_techsupport
Phone: 1.608.782.1610
Our knowledgable customer support team is available:
Mon-Fri 8am-6pm CST
We’re Here to Help SCAN HERE
Additional Info
and Support
Ask questions, watch setup videos, and provide feedback on our social media
outlets. Follow La Crosse Technology on YouTube, Twitter, Facebook and Instagram.
Stay in Touch!
8
SPECIFICATIONS
Atomic Clock (513-1417v6)
Temperature Range: 32°F to 122°F (0°C to 50°C)
Update Interval: About every 51 seconds
Power: 2-AA, IEC, LR6 batteries (not included)
Battery Life: Over 12 months
Dimensions: 11.10” W x 1.14” D x 6.75” H (28.19 W x 2.89 D x 17.15 H cm)
Outdoor Sensor (TX141-Bv4)
Temperature Range: -40°F to 140°F (-40°C to 60°C)
Transmission Range: Over 330 ft. open air
(100 meters) RF 433MHz
Update Interval: About every 51 seconds
Power: 2-AA, IEC, LR6 batteries (not included)
Battery Life: Over 18 months
Dimensions: 1.58” L x 0.83” W x 5.08” H
(3.99cm L x 2.1cm W x 12.99 H cm)
9
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
All rights reserved. This manual may not be reproduced
in any form, even in part, or duplicated or processed using
electronic, mechanical or chemical process without the
written permission of the publisher.
This booklet may contain errors or misprints. The information
it contains is regularly checked and corrections are included
in subsequent editions. We disclaim any responsibility for
any technical error or printing error, or their consequences.
All trademarks and patents are recognized.
FCC Statment
Warranty & Patents
La Crosse Technology, Ltd. provides a 1-year
limited time warranty (from date of purchase) on
this product relating to manufacturing defects in
materials & workmanship.
La Crosse Technology, Ltd,
2830 S. 26th St.
La Crosse, WI 54601
For Full Warranty Details, Visit:
www.lacrossetechnology.com/pages/warranty
Patents:
www.lacrossetechnology.com/pages/patents
Battery Replacement Instructions
When batteries of dierent brand or type are used together,
or new and old batteries are used together, some batteries
may be over-discharged due to a dierence of voltage or
capacity. This can result in venting, leakage, and rupture and
may cause personal injury.
•Always purchase the correct size and grade of battery
most suitable for the intended use.
•Always replace the whole set of batteries at one time,
taking care not to mix old and new ones, or batteries of
dierent types.
•Clean the battery contacts and also those of the device
prior to battery installation.
•Ensure the batteries are installed correctly with regard to
polarity (+ and -).
•Remove batteries from product during periods of non-use.
Battery leakage can cause corrosion and damage to this
product.
•Remove used batteries promptly.
•For recycling and disposal of batteries, and to protect the
environment, please check the internet or your local phone
directory for local recycling centers and/or follow local
government regulations.
Care & Maintenance
Table des matières
Autres manuels La Crosse Technology Horloge
La Crosse Technology
La Crosse Technology WT-8112U Manuel utilisateur
La Crosse Technology
La Crosse Technology WT-3143A Manuel utilisateur
La Crosse Technology
La Crosse Technology WT-3161BKx1 Manuel utilisateur
La Crosse Technology
La Crosse Technology 513-1918S Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-1220 Manuel utilisateur
La Crosse Technology
La Crosse Technology 513-1919 Manuel utilisateur
La Crosse Technology
La Crosse Technology WT-3181 Manuel utilisateur
La Crosse Technology
La Crosse Technology BBB86088 Manuel utilisateur
La Crosse Technology
La Crosse Technology 616-1410B Manuel utilisateur
La Crosse Technology
La Crosse Technology WS-8007U Manuel utilisateur
La Crosse Technology
La Crosse Technology WS-8256-AL Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-1210S Manuel utilisateur
La Crosse Technology
La Crosse Technology 513-1417 Manuel utilisateur
La Crosse Technology
La Crosse Technology WT-3181PLQ Dimensions
La Crosse Technology
La Crosse Technology WT-8008U Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-3451 Manuel utilisateur
La Crosse Technology
La Crosse Technology C86224 Manuel utilisateur
La Crosse Technology
La Crosse Technology 513-1419v4-WA Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-1235UA-SS Manuel utilisateur
La Crosse Technology
La Crosse Technology WS-8011UM-TWC Manuel utilisateur
Manuels Horloge populaires d'autres marques
Silicon Laboratories
Silicon Laboratories SI5324 Manuel utilisateur
Heathkit
Heathkit GC-1005 Manuel utilisateur
Oregon Scientific
Oregon Scientific PRYSMA RMR221P Manuel utilisateur
Andrew O'Malley
Andrew O'Malley DOTKLOK Manuel utilisateur
ALGE-Timing
ALGE-Timing ASC3 Manuel utilisateur
Bodet
Bodet Profil 960 Manuel utilisateur
