La Crosse Technology TX10U Manuel utilisateur
TX10U Rain Sensor
The TX10U rain sensor is used in conjunction with the TX15U wind
sensor and TX8U temperature/ humidity sensor to gather and transmit
information to the wireless weather station. The TX15U wind sensor
measures the wind speed and direction and sends the information to
the TX8U temperature/ humidity sensor. This sensor then transmits all
outdoor weather information from the three outdoor sensors to the
display indoors.
INVENTORY OF CONTENTS
1. TX10U rain sensor
2. Mounting hardware
3. Instruction manual and warranty card
1
SETTING UP
BATTERY INSTALLATION
The first step to powering up the weather station is to insert the
connector (RJ11) at the end of the wire attached to the wind speed
sensor to the remote temperature/humidity sensor. Please ensure
when doing this that the connector is inserted with the proper
orientation. When seated properly you will hear the connector ‘click’ in
place.
A. REMOTE TEMPERATURE/HUMIDITY
1. Remove the mounting bracket and humidity hood.
2. Remove the battery cover by sliding the cover down.
3. Observing the correct polarity install 2 AA batteries.
The batteries will fit tightly (to avoid start-up problems
make sure they do not spring free).
4. Replace the battery cover by sliding upwards. Be
sure battery cover is on securely.
5. Replace the humidity hood.
B. INDOOR WEATHER STATION
1. Remove the battery cover. To do this, insert a solid
object in the space provided at the lower-central
position of the battery cover, then push up and pull
out on the battery cover.
2. Observe the correct polarity, and install 3 AA
batteries.
3. Replace the battery cover.
2
C. RAINFALL SENSOR (optional)
The optional Rain Sensor does not need batteries to operate. Simply
insert the telephone plug (RJ-11) of the rain sensor into the receptacle
on the remote temperature/humidity sensor.
Important: To avoid operating problems, please take note of
battery polarity if inserting any batteries. Also do not
3
Sensor
sockets
Thermo-Hygro
Sensor
Battery
Cover
Battery
Compartment
Sensor
sockets
press any buttons after start up until all sensor
information has been displayed and the radio controlled
time has set. Doing so may interrupt communication
between the sensors and display or interrupt the
WWVB time reception.
1) Pull away the rain cover of the thermo-hygro
sensor to reveal the three sockets (for the wind
sensor, rain sensor and the base station)
2) Connect the attached cables of wind and rain
sensors to the corresponding sockets of the
thermo-hygro sensor by clicking them into place
3) Open the battery cover of the thermo-hygro sensor
located below the three sockets and insert 2 x AA,
IEC LR6, 1.5V batteries and close the cover
4) Open the base station’s battery cover located at
the back of the unit and insert 3 x AA, IEC LR6,
1.5V batteries into the battery compartment and
close the battery cover
Every time the thermo-hygro sensor is powered up (for example after a
change of batteries), a random security code is transmitted and this
code must be synchronized with the base station to receive weather
data.
NOTE FOR WWVB RADIO CONTROLLED TIME:
The time and date display is based on the signal provided by the highly
accurate government operated atomic clock in Ft. Collins, Colorado.
This radio-controlled clock does not only provide for the weather
station’s time and date display but also functions as the time and date
4
source for all of this weather station’s memory values using time and
date information.
MOUNTING THE RAIN SENSOR
For accurate results, the rain sensor should be securely mounted onto
a horizontal surface about 2-3ft above the ground and in an open area
away from trees or other coverings where rainfall may be reduced
causing inaccurate readings.
When securing into place, check that rain excess will not collect and
store at the base of the unit but can flow out between the base and the
mounting surface (test by pouring clean water).
After mounting the rain sensor, connect the cable to the thermo-hygro
sensor at the corresponding socket so power supply can be received
and data be transmitted to the base station
Base
portion
Funnel
p
ortion
The rain sensor is now operable. For testing purposes, very slowly
pour a small amount of clean water into the rain sensor funnel. The
water will act as rainfall and will be received and displayed at the base
5
station after about 2 minutes delay i.e. when the reading interval is
reached.
MAINTENANCE AND CARE
1. Extreme temperatures, vibrations, and shock should be avoided
to prevent damage to the units
2. Clean displays and units with a soft, damp cloth. Do not use
solvents or scouring agents, they may mark the displays and
casings
3. Do not submerge in water.
4. Do not subject the units to unnecessary heat or cold by placing
them in the oven or freezer.
5. Opening the casings invalidates the warranty. Do not try to repair
the unit. Contact La Crosse Technology for repairs.
SPECIFICATIONS
Resolution .01 in
Cable Length 32 feet
Power source Supplied from
temperature/humidity sensor
Dimensions 5.51” x 2.75” x 5.39”
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this
product against manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid
only on products purchased and used in North America and only to the
original purchaser of this product. To receive warranty service, the
purchaser must contact La Crosse Technology, Ltd for problem
6
determination and service procedures. Warranty service can only be
performed by a La Crosse Technology, Ltd authorized service center.
The original dated bill of sale must be presented upon request as proof
of purchase to La Crosse Technology, Ltd or La Crosse Technology,
Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our
option and at no charge as stipulated herein, with new or reconditioned
parts or products if found to be defective during the limited warranty
period specified above. All replaced parts and products become the
property of La Crosse Technology, Ltd and must be returned to La
Crosse Technology, Ltd. Replacement parts and products assume the
remaining original warranty, or ninety (90) days, whichever is longer.
La Crosse Technology, Ltd will pay all expenses for labor and
materials for all repairs covered by this warranty. If necessary repairs
are not covered by this warranty, or if a product is examined which is
not in need or repair, you will be charged for the repairs or
examination. The owner must pay any shipping charges incurred in
getting your La Crosse Technology, Ltd product to a La Crosse
Technology, Ltd authorized service center. La Crosse Technology, Ltd
will pay reasonable return shipping charges to the owner of the
product.
Your La Crosse Technology, Ltd warranty covers all defects in material
and workmanship with the following specified exceptions: (1) damage
caused by accident, unreasonable use or neglect (including the lack of
reasonable and necessary maintenance); (2) damage occurring during
shipment (claims must be presented to the carrier); (3) damage to, or
deterioration of, any accessory or decorative surface; (4) damage
resulting from failure to follow instructions contained in your owner’s
7
manual; (5) damage resulting from the performance of repairs or
alterations by someone other than an authorized La Crosse
Technology, Ltd authorized service center; (6) units used for other than
home use (7) applications and uses that this product was not intended
or (8) the products inability to receive a signal due to any source of
interference. This warranty covers only actual defects within the
product itself, and does not cover the cost of installation or removal
from a fixed installation, normal set-up or adjustments, claims based
on misrepresentation by the seller or performance variations resulting
from installation-related circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY
FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER
SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR
MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO
BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC
INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other
rights specific to your State. Some States do no allow the exclusion of
consequential or incidental damages therefore the above exclusion of
limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology, Ltd
190 Main Street
La Crescent, MN 55947
Phone: 507.895.7095
Fax: 507.895.2820
8
e-mail:
sales@lacrossetechnology.com (information on other products)
web:
www.lacrossetechnology.com
All rights reserved. This handbook must not be reproduced in any form, even in
excerpts, or duplicated or processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors. The information in this
handbook is regularly checked and corrections made in the next issue. We
accept no liability for technical mistakes or printing errors, or their consequences.
All trademarks and patents are acknowledged.
9
Table des matières
Autres manuels La Crosse Technology Accessoires
La Crosse Technology
La Crosse Technology TX-23U Manuel utilisateur
La Crosse Technology
La Crosse Technology TX24U Manuel utilisateur
La Crosse Technology
La Crosse Technology TX141TH-BV4 Manuel utilisateur
La Crosse Technology
La Crosse Technology TX8U Manuel utilisateur
La Crosse Technology
La Crosse Technology CA82738-1 Manuel utilisateur
La Crosse Technology
La Crosse Technology CA79097 Manuel utilisateur
La Crosse Technology
La Crosse Technology TX15U Manuel utilisateur
La Crosse Technology
La Crosse Technology TX-63U-IT Manuel utilisateur
La Crosse Technology
La Crosse Technology TX141-Bv2 Manuel utilisateur
La Crosse Technology
La Crosse Technology D012.104.E1 Manuel utilisateur
La Crosse Technology
La Crosse Technology TX9U Manuel utilisateur
La Crosse Technology
La Crosse Technology LTV-W2 Manuel utilisateur
La Crosse Technology
La Crosse Technology TX21U Manuel utilisateur
La Crosse Technology
La Crosse Technology LTV-R1 Manuel utilisateur
La Crosse Technology
La Crosse Technology LTV-R2 Manuel utilisateur
La Crosse Technology
La Crosse Technology TX7U Manuel utilisateur
La Crosse Technology
La Crosse Technology WCLTV-WSDR1 Manuel utilisateur
La Crosse Technology
La Crosse Technology TX141-B4 Manuel utilisateur
La Crosse Technology
La Crosse Technology CYCLONE PRO SENSOR Manuel utilisateur
La Crosse Technology
La Crosse Technology LTV-R3 Manuel utilisateur
