KTM 450 EXC-F 2021 Manuel

SETUP INSTRUCTIONS 2021

450 EXC‑F

450 EXC‑F SIX DAYS

500 EXC‑F

500 EXC‑F SIX DAYS

500 XCF‑W

Art. no. 3214378en

INTRODUCTION

*3214378en*

3214378en

02/2021

INTRODUCTION

Perform the work described in these setup instructions before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make

changes in the interest of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop

are not specified here. It is assumed that the work will be performed by a fully trained mechanic.

All specifications contained herein are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right

to modify or delete technical specifications, prices, colors, forms, materials, services, designs, equipment, etc.,

without prior notice and without specifying reasons, to adapt these to local conditions, as well as to stop produc-

tion of a particular model without prior notice. KTM accepts no liability for delivery options, deviations from fig-

ures and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that

does not belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission

of the copyright owner.

ISO 9001(12 100 6061)

KTM applies quality assurance processes that lead to the highest possible product quality as

defined in the ISO 9001 international quality management standard.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

Stallhofnerstraße 3

5230 Mattighofen, Austria

This document is valid for the following models:

450 EXC‑F EU (F8403U9)

450 EXC‑F SIX DAYS EU (F8403U2)

500 EXC‑F EU (F8503U9)

500 EXC‑F US (F8575U9)

500 EXC‑F SIX DAYS EU (F8503U2)

500 EXC‑F SIX DAYS US (F8575U2)

500 XCF-W US (F8575U1)

1 MEANS OF REPRESENTATION

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Indicates a voltage measurement.

Indicates a current measurement.

Indicates a resistance measurement.

Indicates the end of an activity including potential rework.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Indicates a proprietary name.

Name®Indicates a protected name.

Brand™ Indicates a brand available on the open market.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which

are explained in the glossary.

SETUP 2

2.1 Transport mode

H02712-01

This vehicle was blocked for transport in the software.

To operate the vehicle, the vehicle electronics must be enabled.

This process is conducted during initial setup in KTM Dealer.net.

Enabling ensures that the initial setup in KTM Dealer.net is docu-

mented.

Enabling can be performed either temporarily, e.g. for a test ride,

or permanently for vehicle handover.

Info

Make sure that the vehicle is permanently enabled before

handing it over to the customer.

2.2 Unpacking and setting up the vehicle

E00851-10

Condition

Packaging V2

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling

over.

To avoid damaging the motorcycle during the setup,

leave the protective film on the vehicle until you

have finished.

–Remove the separate enclosure and unpack it. Check that

the scope of supply is complete using the enclosed pack-

ing list.

–Have a lift stand available.

Lift stand (78129955100)

–Carefully loosen and remove the tension belt of the footrest

mount.

Info

An assistant prevents the motorcycle from falling

over.

402050-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

–Remove the headlight mask with the headlight. ( p. 19)

2 SETUP

H01768-10

–Position turn signal indicator lamp 1in the combination

instrument rack.

E00850-10

Condition

Packaging V12

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling

over.

To avoid damaging the motorcycle during the setup,

leave the protective film on the vehicle until you

have finished.

–Remove and unpack the separate enclosure and compo-

nents. Check that the scope of supply is complete using

the enclosed packing list.

–Have a lift stand available.

Lift stand (78129955100)

–Remove the two cable ties on the triple clamp.

402051-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle and components for transport damage.

–Install the shock absorber. ( p. 22)

H01768-10

–Position turn signal indicator lamp 1in the combination

instrument rack.

SETUP 2

402736-10

–Position the connector board and combination instrument

on the upper triple clamp.

–Mount and tighten screws 2.

Guideline

Remaining screws,

chassis

M6 10 Nm (7.4 lbf ft)

–Route the clutch line with the clutch master cylinder

toward the front between the upper and lower triple

clamps.

–Install the fork legs. ( p. 22)

S01414-10

(EXC‑F EU/US, XCF‑W)

–Remove screws 3and take off the handlebar supports.

–Move the handlebar supports to the desired position and

mount and tighten screws 3.

Guideline

Screw, handle-

bar holder

M10 40 Nm (29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports

evenly.

E00483-01

Warning

Danger of accidents A repaired handlebar poses a

safety risk.

If the handlebar is bent or straightened, the mate-

rial becomes fatigued. The handlebar may break

as a result.

–Change the handlebar if the handlebar is dam-

aged or bent.

–Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Position the handlebar clamps. Mount and tighten the

screws evenly.

Guideline

Screw, handlebar

clamp

M8 20 Nm

(14.8 lbf ft)

2 SETUP

Info

The markings on the handlebar should be at the

center of the handlebar clamps.

Keep the installed gap widths equal when tighten-

ing.

S01415-10

(EXC‑F SIX DAYS)

–Remove screws 3and take off the handlebar supports.

–Move the handlebar supports to the desired position and

mount and tighten screws 3.

Guideline

Screw, handle-

bar holder

M10 40 Nm (29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports

evenly.

S01413-01

Warning

Danger of accidents A repaired handlebar poses a

safety risk.

If the handlebar is bent or straightened, the mate-

rial becomes fatigued. The handlebar may break

as a result.

–Change the handlebar if the handlebar is dam-

aged or bent.

–Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Position the handlebar clamps. Mount and tighten the

screws evenly.

Guideline

Screw, handlebar

clamp

M8 20 Nm

(14.8 lbf ft)

SETUP 2

Info

The markings on the handlebar should be at the

center of the handlebar clamps.

Keep the installed gap widths equal when tighten-

ing.

S03665-01

(All EU models)

–Position the controls on the right half of the handlebar.

E01235-01

(500 EXC‑F US, 500 EXC‑F SIX DAYS US)

–Position the controls on the right half of the handlebar.

S03667-01

(XCF‑W)

–Position the controls on the right half of the handlebar.

S01423-01

(All EU models)

–Position the controls on the left handlebar half.

2 SETUP

S01410-01

(500 EXC‑F US, 500 EXC‑F SIX DAYS US)

–Position the controls on the left handlebar half.

S03666-01

(XCF‑W)

–Position the controls on the left handlebar half.

S01422-01

(EXC‑F SIX DAYS EU, XCF‑W)

Warning

Voiding of the government approval for road use and

the insurance coverage If the combination switch

is mounted, the vehicle’s road permit, if any,

expires.

–Only operate the vehicle in closed-off areas

remote from public road traffic if the combina-

tion switch is installed.

–(Optional) Mount combination switch on the left side.

Info

The figure shows a possible installation position of

the left side combination switch.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KTM Moto

KTM

KTM 1290 Super Duke R EU 2014 Mode d'emploi

KTM

KTM 890 Adventure 2021 Manuel

KTM

KTM 250 XC-F, XCF-W, EXC-F, 400 XC-W, EXC RACING, 450 XC, XC-W, EXC RACING, 525 XC, XC-W, EXC RACING, 525 XC DESERT... Manuel utilisateur

KTM

KTM Freeride 250 R EU Manuel utilisateur

KTM

KTM 350 EXC-F EU 2014 Manuel

KTM

KTM 2013 1190 RC8 R JP Manuel utilisateur

KTM

KTM 640 DUKE II 2001 Guide de l'utilisateur

KTM

KTM 85 SX Manuel utilisateur

KTM

KTM 60 65 SX Manuel utilisateur

KTM

KTM 2010 690 SMC EU Manuel

KTM

KTM 250 EXC-F EU 2013 Manuel

KTM

KTM 65 SX 2006 Manuel utilisateur

KTM

KTM 450 EXC-F 2020 Manuel

KTM

KTM 790 Adventure 2020 Manuel

KTM

KTM 250 SX F PRADO 2020 Manuel

KTM

KTM 790 Adventure 2019 Manuel utilisateur

KTM

KTM 125 DUKE EU Manuel utilisateur

KTM

KTM 350 EXC-F 2019 Manuel utilisateur

KTM

KTM 65 SX 2009 Mode d'emploi

KTM

KTM 350 EXC-F EU 2019 Manuel

KTM

KTM 890 DUKE 2022 Manuel

KTM

KTM 690 Duke 2018 Manuel utilisateur

KTM

KTM 1290 Super Adventure EU 2015 Manuel

KTM

KTM 400 SX RACING 2000 Guide de l'utilisateur

Manuels Moto populaires d'autres marques

OHVALE

OHVALE GP-0 Manuel de la liste des pièces

Yamaha

Yamaha Star XV19CTSZ 2009 Manuel utilisateur

HYOSUNG

HYOSUNG ST7 Manuel utilisateur

Husqvarna

Husqvarna FC 250 2016 Manuel utilisateur

Ducati

Ducati SCRAMBLER 800 Manuel d'instructions

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Manuel utilisateur

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manuel utilisateur

Yamaha

Yamaha 2006 YZF-R1V Manuel utilisateur

Fantic

Fantic Enduro 125 Manuel utilisateur

Ducati

Ducati Supersport 750 desmodue Manuel utilisateur

MV Agusta

MV Agusta 2008 F4 312RR 1078 Manuel d'instructions

Yamaha

Yamaha XVS650A Manuel utilisateur

Yamaha

Yamaha YZF-R6T(C) Manuel

Ducati

Ducati 748 monoposto strada Manuel utilisateur

ATK

ATK 1988 250 Manuel utilisateur

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Manuel utilisateur

Triumph

Triumph Thunderbird Manuel utilisateur

Yamaha

Yamaha 2006 FJR1300A Manuel utilisateur