KROHNE OPTIPROBE Manuel utilisateur

The cost efficient flow indicator

OPTIPROBE

OPTIPROBEOPTIPROBE

OPTIPROBE Quick Start

Quick StartQuick Start

Quick Start

CONTENTS

2 www.krohne.com 01/2014 - 4003344001 - QS OPTIPROBE R02 en

OPTIPROBE

1 Safety instructions 3

2 Installation 4

2.1 General notes on installation ........................................................................................... 4

2.2 Scope of delivery............................................................................................................... 4

2.3 Nameplate ........................................................................................................................ 5

2.4 Installation conditions ...................................................................................................... 6

2.4.1 Inlet and outlet ........................................................................................................................ 6

2.4.2 Mounting position.................................................................................................................... 6

2.4.3 T-section ................................................................................................................................. 7

2.4.4 Vibration .................................................................................................................................. 7

2.4.5 Magnetic field.......................................................................................................................... 7

2.4.6 Pump ....................................................................................................................................... 7

2.4.7 Control valve ........................................................................................................................... 8

2.4.8 Bends ...................................................................................................................................... 8

2.4.9 Open discharge ....................................................................................................................... 9

2.4.10 Temperatures ....................................................................................................................... 9

2.5 Mounting and dismounting............................................................................................. 10

3 Electrical connections 11

3.1 Safety instructions.......................................................................................................... 11

3.2 Connection diagram ....................................................................................................... 11

SAFETY INSTRUCTIONS 1

OPTIPROBE

www.krohne.com01/2014 - 4003344001 - QS OPTIPROBE R02 en

Warnings and symbols used

HANDLING

• This symbol designates all instructions for actions to be carried out by the operator in the

specified sequence.

iRESULT

RESULTRESULT

RESULT

This symbol refers to all important consequences of the previous actions.

Safety instructions for the operator

DANGER!

This information refers to the immediate danger when working with electricity.

DANGER!

These warnings must be observed without fail. Even partial disregard of this warning can lead to

serious health problems and even death. There is also the risk of seriously damaging the device

or parts of the operator's plant.

WARNING!

Disregarding this safety warning, even if only in part, poses the risk of serious health problems.

There is also the risk of damaging the device or parts of the operator's plant.

CAUTION!

Disregarding these instructions can result in damage to the device or to parts of the operator's

plant.

INFORMATION!

These instructions contain important information for the handling of the device.

CAUTION!

Installation, assembly, start-up and maintenance may only be performed by appropriately

trained personnel. The regional occupational health and safety directives must always be

observed.

LEGAL NOTICE!

The responsibility as to the suitability and intended use of this device rests solely with the user.

The supplier assumes no responsibility in the event of improper use by the customer. Improper

installation and operation may lead to loss of warranty. In addition, the "Terms and Conditions of

Sale" apply which form the basis of the purchase contract.

INFORMATION!

•

Further information can be found on the supplied CD-ROM in the manual, on the data sheet,

in special manuals, certificates and on the manufacturer's website.

•

If you need to return the device to the manufacturer or supplier, please fill out the form

contained on the CD-ROM and send it with the device. Unfortunately, the manufacturer

cannot repair or inspect the device without the completed form.

2INSTALLATION

OPTIPROBE

www.krohne.com 01/2014 - 4003344001 - QS OPTIPROBE R02 en

2.1 General notes on installation

2.2 Scope of delivery

The OPTIPROBE is available in two models. You receive the ordered version.

INFORMATION!

Inspect the cartons carefully for damages or signs of rough handling. Report damage to the

carrier and to the local office of the manufacturer.

INFORMATION!

Do a check of the packing list to make sure that you have all the elements given in the order.

INFORMATION!

Look at the device nameplate to ensure that the device is delivered according to your order.

Check for the correct supply voltage printed on the nameplate.

1 Model A, for fixed mounting with welded-on flange.

2 Model B, for mounting with variable insertion lengths.

INSTALLATION 2

OPTIPROBE

www.krohne.com01/2014 - 4003344001 - QS OPTIPROBE R02 en

2.3 Nameplate

1 OPTIPROBE, model A or B

2 Quick Start

3 Factory calibration certificate

INFORMATION!

Look at the device nameplate to ensure that the device is delivered according to your order.

Check for the correct supply voltage printed on the nameplate.

1 Name and address of the manufacturer.

2 Type designation of the flowmeter and CE sign.

3 Calibration data.

2INSTALLATION

OPTIPROBE

www.krohne.com 01/2014 - 4003344001 - QS OPTIPROBE R02 en

2.4 Installation conditions

2.4.1 Inlet and outlet

2.4.2 Mounting position

Figure 2-1: Recommended inlet and outlet sections

1 ≥10 DN

2 ≥5 DN

Figure 2-2: Mounting position

1 Flow profile must be fully developped.

2 Welding instructions: the electrodes must point to the side of the pipeline!

3 Insert the OPTIPROBE perpendicular.

4 Insertion length ≥25mm.

5 DN ≥80mm.

CAUTION!

The OPTIPROBE is a sensor which measures flow speed at one point in the pipe.

In case the flow speed has to be converted into a volume, please note that the measured value

depends on the used diameter and the insertion length, because the OPTIPROBE decreases the

inner surface of the pipe at the measuring section. The corrected GKl value for any other

installation condition can be calculated as:

All measures in mm

GKl

cal

is GKl on nameplate

INSTALLATION 2

OPTIPROBE

www.krohne.com01/2014 - 4003344001 - QS OPTIPROBE R02 en

2.4.3 T-section

2.4.4 Vibration

2.4.5 Magnetic field

2.4.6 Pump

Figure 2-3: Distance after T-sections

1 ≥30 DN

Figure 2-4: Avoid vibrations

Figure 2-5: Avoid magnetic fields

Figure 2-6: Installation after pump

2INSTALLATION

OPTIPROBE

www.krohne.com 01/2014 - 4003344001 - QS OPTIPROBE R02 en

2.4.7 Control valve

2.4.8 Bends

Figure 2-7: Installation before control valve

Figure 2-8: Installation in bending pipes

Figure 2-9: Installation in bending pipes

INSTALLATION 2

OPTIPROBE

www.krohne.com01/2014 - 4003344001 - QS OPTIPROBE R02 en

2.4.9 Open discharge

2.4.10 Temperatures

Figure 2-10: Installation before an open discharge

1 Process temperature

2 Ambient temperature

CAUTION!

Protect the device from direct sunlight.

Temperature range [ºC] [ºF]

min. max. min. max.

Process temperature 0100 32 212

Ambient temperature -30 55 -22 131

2INSTALLATION

OPTIPROBE

www.krohne.com 01/2014 - 4003344001 - QS OPTIPROBE R02 en

2.5 Mounting and dismounting

The following instruction is to be used when it is necessary to mount or dismount the

OPTIPROBE measuring sensor (model B only !).

Dismounting

1. Make sure that the safety chain is correctly installed to secure the OPTIPROBE

2. Loosen the bolt 1in picture below, until the unit can be slided out of the gland. Be aware that

if the pressure is sufficiently high the unit can slide out without pulling, or even force out when

pressure in the installation is high.

3. Slide out the OPTIPROBE unit as far as possible (allowed by the chain).

4. Close the valve. Remind that the volume above the valve is still pressurized.

5. Loosen the bolts 2in picture below, to release pressure.

6 Dismount the chain and remove the OPTIPROBE.

Mounting the OPTIPROBE

1. Loosen the bolt 1in picture above, until the unit can be slided in the gland.

2. Loosen the bolts 2in picture above ( if necessary, it can make it easier to slide the unit back

in).

3 Mount the security chain and make sure it is correctly assembled

4. Tighten the bolts 2in picture above. Be sure the safety chain is attached and the bolts are

tighted !

5 Carefully open the valve.

6. Slide in the OPTIPROBE into the desired position. This might require force, depending on the

pressure in the installation.

7. Tighten bolt 1in picture above.

Table des matières

Autres manuels KROHNE Instrument de mesure

KROHNE

KROHNE OPTISONIC 1400 Manuel utilisateur

KROHNE

KROHNE OPTISWITCH 3000 C Manuel utilisateur

KROHNE

KROHNE OPTISWIRL 4200 Manuel utilisateur

KROHNE

KROHNE OPTISWIRL 2100 Manuel utilisateur

KROHNE

KROHNE VFC 200 Schéma de câblage

KROHNE

KROHNE OPTISWITCH 3300 C Manuel utilisateur

KROHNE

KROHNE OPTIFLUX 7300 Manuel utilisateur

KROHNE

KROHNE AF-E 400 Manuel utilisateur

KROHNE

KROHNE OPTIFLUX 7300 Manuel utilisateur

KROHNE

KROHNE SMARTPAT COND 5200 Schéma de câblage

KROHNE

KROHNE BATCHFLUX 5500 C Manuel utilisateur

KROHNE

KROHNE OPTISONIC 6300 F Manuel utilisateur

KROHNE

KROHNE optiplex 1300 c Manuel utilisateur

KROHNE

KROHNE BATCHFLUX 3200 C Schéma de câblage

KROHNE

KROHNE OPTISONIC 3400 Schéma de câblage

KROHNE

KROHNE Optisonic 6300 P Manuel utilisateur

KROHNE

KROHNE Optisonic 6300 P Manuel utilisateur

KROHNE

KROHNE WATERFLUX 3070 Manuel utilisateur

KROHNE

KROHNE BM 70 A Manuel utilisateur

KROHNE

KROHNE OPTIWAVE 3500 C Manuel utilisateur

KROHNE

KROHNE OPTISONIC 6300 Mode d’emploi

KROHNE

KROHNE OPTIMASS 1400 Manuel utilisateur

KROHNE

KROHNE WATERFLUX 3070 Manuel utilisateur

KROHNE

KROHNE OPTISONIC 3400 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur