Kramer VP-440H2 Manuel utilisateur

VP-440H2 Quick Start

P/N:

2900- 300930QS

Rev:

Scan for full manual

VP-440H2 Quick Start Guide

This guide helps you install and use your VP-440H2 for the first time.

Go to www.kramerav.com/downloads/VP-440H2 to download the latest user manual and

check if firmware upgrades are available.

Step 1: Check what’s in the box

VP-440H2 4K Presentation Switcher / Scaler

1 Power cord

4 Rubber feet

1 Power supply (48V DC)

1 Quick start guide

Step 2: Get to know your VP-440H2

Feature

Function

48 V () Slide Switch

Slide up (48V) to select a condenser type microphone; slide down to select a dynamic

type microphone (we recommend that you slide down if a microphone is not connected to

the VP-440H2).

MIC 6.3mm Jack

Connect to the microphone source.

Input Selector

Buttons

HDBT IN

Press to select the HDBT input.

HDMI IN

Press to select the HDMI input (from 1 to 3).

PC IN

Press to select the computer graphics input.

MENU Button

Displays the OSD menu.

Navigation

Buttons



Press to decrease numerical values or select from several definitions.

When not in the OSD menu, press to reduce the output volume.



Press to move up the menu list values.



Press to increase numerical values or select from several definitions.

When not in the OSD menu, press to increase the output volume.



Press to move down the menu list.

ENTER

Press to accept changes and change the SETUP parameters.

RESET TO XGA/1080p Button

Press and hold for about 5 seconds to toggle the output resolution between XGA and

1080p, alternatively.

PANEL LOCK Button

Press and hold for about 5 seconds to lock/unlock the front panel buttons.

Feature

Function

CONTROL (Tx, Rx, GND) Terminal

Block Connectors

Connect to the PC or the serial controller to control the device.

HDBT IN (Tx, Rx, GND) Terminal

Block Connectors

Connect to a controller to control peripheral devices that are connected to the

HDBT transmitter (for example, a Blu-ray player connected to WP-20).

HDBT OUT (Tx, Rx, GND) Terminal

Block Connectors

Connect to a controller to control peripheral devices that are connected to the

HDBT receiver (for example, a projector connected to TP-580Rxr).

AUDIO INPUT

Unbalanced

Stereo 3.5 Mini

Jack

HDMI

Connect to the analog audio HDMI source (from 1 to 3).

Connect to the analog audio computer graphics source.

AUDIO OUT 3.5 Mini Jack

Connect to an unbalanced stereo audio acceptor.

ETHERNET Connector

Connects to the PC or other controller through computer networking.

VIDEO INPUT

Connectors

HDBT IN RJ-45

Connect to an HDBT transmitter (for example, WP-20).

Can supply PoE (up to 13W) to the transmitter.

HDMI IN

Connect to the HDMI source (from 1 to 3).

PC IN on15-pin

Connect to the computer graphics source.

HDBT OUT RJ-45 Connector

Connect to an HDBT receiver (for example, TP-580Rxr).

HDMI OUT Connector

Connect to the HDMI acceptor.

48V DC Power Terminal Block

+48V DC connector for powering the unit.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Step 3: Install VP-440H2

Install VP-440H2 using one of the following methods:

•Attach the rubber feet and place the unit on a flat surface.

•Mount the unit in a rack using the recommended rack adapter

(see www.kramerav.com/product/VP-440H2)

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VP-440H2. For best results, we recommend that

you always use Kramer high-performance cables to connect AV equipment to VP-440H2.

RJ-45 Pinout:

Microphone Pinout:

For the Ethernet connector, see the wiring

diagram below

The microphone 6mm jack pinout for a condenser microphone

The microphone 6mm jack pinout for a dynamic microphone.

PIN EIA /TIA 568B

Wire Color

Orange /

White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

For optimum range and performance use the recommended Kramer cables available at

www.kramerav.com/product/VP-440H2.

For HDBT cables, it is recommended that the cable ground shielding be connected/soldered to the connector

shield.

Step 5: Connect the power

Connect the power cord to VP-440H2 and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 6: Control and operate VP-440H2 via the front panel buttons and via

Web pages:

OSD Menu:

Menu Items

Picture

Adjust contrast brightness and color and fine-tune the image.

Input

Select input source.

Output

Select method for 4K input to 4K output handling, image size and

resolution.

Audio

Select audio source, audio parameters (bass, treble and so on),

microphone settings and volume per input.

OSD

Set OSD position, transparency and so on.

Advanced

Select HDCP on each of the inputs and outputs, manage the EDID and

define IP settings.

Info.

View device information.

Factory

Reset to factory default settings.

Autres manuels pour VP-440H2

Autres manuels Kramer Changer

Kramer

Kramer VM-114H4C Manuel utilisateur

Kramer

Kramer VS-21HDCP-IR Manuel utilisateur

Kramer

Kramer VP-740 ProScale Manuel utilisateur

Kramer

Kramer VS-211HA Manuel utilisateur

Kramer

Kramer VM-3H2 Manuel utilisateur

Kramer

Kramer VP-550X Manuel utilisateur

Kramer

Kramer VP-730 Manuel utilisateur

Kramer

Kramer VS-812 Manuel utilisateur

Kramer

Kramer VS-41H2 Manuel utilisateur

Kramer

Kramer VP-774AMP Manuel utilisateur

Kramer

Kramer VP-725XLA Manuel utilisateur

Kramer

Kramer VS-34FD Manuel utilisateur

Kramer

Kramer Wall Plate Series Manuel utilisateur

Kramer

Kramer SWT3-31-HU Manuel utilisateur

Kramer

Kramer PL-15 Manuel utilisateur

Kramer

Kramer WP-20 Manuel utilisateur

Kramer

Kramer VS-4x4FW Manuel utilisateur

Kramer

Kramer VP-440 Manuel utilisateur

Kramer

Kramer VM-218DTxr Manuel utilisateur

Kramer

Kramer 6241HDx1 Manuel utilisateur

Kramer

Kramer VS-24xl Manuel utilisateur

Kramer

Kramer VS-21A Manuel utilisateur

Kramer

Kramer VS-24x1 Manuel utilisateur

Kramer

Kramer VP-734 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur