Kramer VS-44H2 Manuel utilisateur

VS-44H2 Quick Start

P/N:

2900- 301297QS

Rev:

Scan for full manual

VS-44H2 Quick Start Guide

This guide helps you install and use your VS-44H2 for thefirst time.

Go to www.kramerav.com/downloads/VS-44H2to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VS-44H2 4K 4x4 Matrix Switcher

4 Rubber feet

1 Quick start guide

1 Set of rackears

1 Power cord

Step 2: Get to know your VS-44H2

Feature

Function

IN Select Buttons (1 to 4)

Press to select the input to switch after selecting an output (also used for storing

machine setups).

OUT Select Buttons (1 to 4)

Press to select an output to switch followed by an input.

MUTE/PATTERN Button

Press to view the current pattern status and select the output/s to which a pattern is

routed.

Press to mute audio and video on a selected output.

ALL Button

Press followed by an input button to connect the selected input to all outputs.

For example, press ALL and then Input button # 2 to connect input # 2 to all the

outputs.

STO Button

Press STO followed by an IN or OUT (1 to 4) button to store the current switching

configuration to the location corresponding to that INPUT number.

RCL Button

Press RCL followed by the corresponding IN or OUT (1 to 4) button to recall the

preset switching configuration saved in that location.

LOCK Button

Press and hold to toggle between locking and releasing the front panel buttons.

EDID Button

Press to enter the EDID mode.

OUTPUT/INPUT 7-segment LED

Display

Displays the input currently switched to the output which is marked above each input.

Feature

Function

HDMI™ IN Connectors (1 to 4)

Connect to up to 4 HDMI sources.

HDMI OUT Connectors (1 to 4)

Connect to up to 4 HDMI acceptors.

5V/2A USB Port

Use to charge a device.

PROG USB Mini port

Connect to a PC/serial controller to control the device.

Reset Button

Press and hold for about 8 seconds to reset IP settings to factory default values.

ETHERNET RJ-45 Connector

Connect to a PC via a LAN.

RS-232 9-pin D-sub Connector

Connect to a PC/serial controller to control the device.

Mains Power Connector Fuse

Plug in the power cord.

Power Illuminated Switch

Turn the device on and off.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Step 3: Mount VS-44H2

To rack mount the machine, attach both rack ears

(by removing the screws from each side of the

machine and replacing those screws through the

rack ears) or place the machine on a table.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-44H2. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the VS-44H2.

Step 5: Connect power

Connect the power cord to VS-44H2 and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection,located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 6: Operate the VS-44H2

Operate via RS-232 and Ethernet communication parameters:

RS-232/Ethernet

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII Protocol 3000

Stop Bits:

Example (route video HDMI IN 4 to video HDMI OUT 1):

“#X-ROUTE

OUT.HDMI.1.VIDEO.1,IN.HDMI.4.VIDEO.1”,0x0D

Ethernet Parameters

IP Address:

192.168.1.39

Default TCP Port #:

5000

Subnet Mask:

255.255.0.0

Default UDP Port #:

50000

Default Gateway:

192.168.0.1

Username/Password:

Admin/Admin

Full Factory Reset

Front panel:

There is no option for factory reset from front panel.

Protocol 3000:

“#factory” command.

Web Pages:

Device Settings page, Soft Factory Reset resets all parameters to factory default except for network

parameters.

Operate via Front Panel Buttons

Switch an input to an output via front panel buttons

Press an output button followed by an input button to switch the selected input to the selected output.

Switch an input simultaneously to all 4 outputs

1. Press ALL. All 4 outputs on the 7-segment display flash.

2. Press an input button. The selected input is routed to all the outputs.

Store a switching setting

1. Configure the switching as required for the preset.

2. Press STO. The STO button flashes.

3. Press an input or output button (1-4). The input or output button flashes

and the STO button stops flashing.

Recall a switching setting

1. Press RCL. The RCL button flashes.

2. Press the relevant input or output button that stored the preset.

Once the stored preset is recalled, the RCL button stops flashing.

Acquiring the EDID

Acquire EDID from:

•One output to one or more of the inputs.

•Different outputs to different inputs.

•The default EDID (by reading EDID from an output that is not connected to an acceptor).

To acquire an EDID from an output to one or more inputs:

1. Make sure that the output is connected to an acceptor.

2. Press EDID (short press). EDID button lights.

The 7-segment display shows the current EDID status.

3. Press one or more input buttons (to which the EDID is copied) or press ALL (to copy EDID to all the inputs).

The corresponding 7-segment LEDs flash.

4. Press the output button (from which the EDID is acquired).

The 7-segment LEDs show the output number from which the EDID is read.

5. Press and hold EDID until the device acquires the EDID and device exits EDID mode (EDID and STO button lights

turn off).

If the output is not connected to an acceptor, the 7-segment display shows “d”. When reading the EDID from

an unconnected output, the default EDID is restored.

Autres manuels pour VS-44H2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kramer Commutateur matriciel

Kramer

Kramer Sierra Pro XL 1608V5S Manuel utilisateur

Kramer

Kramer VP-4x4K Manuel utilisateur

Kramer

Kramer 6464V5XL Manuel utilisateur

Kramer

Kramer Sierra Video 1608V3S Manuel utilisateur

Kramer

Kramer VP-8x4 Manuel utilisateur

Kramer

Kramer VS-3232DN-EM Manuel utilisateur

Kramer

Kramer VS-606xl Manuel utilisateur

Kramer

Kramer VS-6464DN-EM Manuel utilisateur

Kramer

Kramer VS-88HDxl Manuel utilisateur

Kramer

Kramer XL 1204V2 Manuel utilisateur

Kramer

Kramer Sierra Video 1204V5S Manuel utilisateur

Kramer

Kramer VP-12x8 Manuel utilisateur

Kramer

Kramer VS-62HA Manuel utilisateur

Kramer

Kramer VS-162V Manuel utilisateur

Kramer

Kramer XL 1616V2S Manuel utilisateur

Kramer

Kramer XL 1204V Manuel utilisateur

Kramer

Kramer 88HD Manuel utilisateur

Kramer

Kramer VS-1604 Manuel utilisateur

Kramer

Kramer VP-128H Manuel utilisateur

Kramer

Kramer VS-44UHD Manuel utilisateur

Kramer

Kramer XL 1608V4S Manuel utilisateur

Kramer

Kramer Sierra Video 3232V3S Manuel utilisateur

Kramer

Kramer VS-4x4YCx1 Manuel utilisateur

Kramer

Kramer Sierra Pro XL 1208V5S Manuel utilisateur

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Roland

Roland XS-1HD Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes

Lindy

Lindy 38042 Manuel utilisateur

Extron electronics

Extron electronics MTPX Plus Series Manuel utilisateur

Key Digital

Key Digital Champion KD-16x16CS Manuel utilisateur

Shinybow USA

Shinybow USA SB-8811 Manuel utilisateur

Optimus

Optimus Compact Manuel utilisateur