Kramer VS-3232DN-EM Manuel utilisateur

-3232DN-EM Quick Start (P/N: 2900-300932QS REV 1)

P/N:

2900- 300932QS

Rev:

Scan for full manual

VS-3232DN-EM Quick Start Guide

This guide helps you install and use your VS-3232DN-EM for the first time.

Go to www.kramerav.com/downloads/VS-3232DN-EM to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VS-3232DN-EM 4x4 to 32x32 Modular Multi-

Format Managed Digital Matrix Switcher

1 Set of rack ears (attached) 1 Quick start guide

Infrared remote control transmitter with batteries

1 Power cord

Step 2: Get to know your VS-3232DN-EM

# Feature Function

Double-

function

Selector

Buttons

Area

Button

Functions

ESC

Press to exit the current operation.

2 EDID Press to assign EDID channels.

3 STO Press to store the current setup in a preset. After pressing the MENU button, this button lights

and is enabled.

4 ALL Press to connect an input to all outputs. After pressing the MENU button, this button lights and

is enabled.

OFF

Press to turn off an output. After pressing the MENU button, this button lights and is enabled.

6 RCL Press to recall a preset. After pressing the MENU button, this button lights and is enabled.

7 DELAY Press to set the delay between confirming an action and the execution of the action.

8 ENT Press to complete the input-output setup when using a one-digit number instead of two digits.

For example, to enter input 5, you can press either 05 or 5, ENTER.

Press to enter the options in a setup menu.

BREAKAWAY Button

Press to exit a menu.

# Feature Function

DEFAULT SETUP Button

Press to recall the default setup.

11 OUTPUTS/INPUTS

LCD Display

Displays the outputs (upper row) switched to the selected inputs (lower row).

Displays user interface messages and menus.

12 IR Receiver Infrared remote control sensor.

13 IR LED Lights yellow when receiving commands from the IR remote control transmitter.

TAKE Button

Press to confirm actions.

15 MENU Button Press once to enable the ALL, OFF, STO and RCL buttons.

Press again to enter the configuration menu.

When in a Menu, press to cycle through the menu items.

16 LOCK Button Press and hold for approximately 2 sec to lock/unlock the front panel buttons.

17 Power Supply Supplies power to the device.

POWER LED

Lights green when power supply is active and the device is powered on.

20 ERROR LED Lights red when an error is detected. Briefly lights red immediately following a power disruption

(e.g., cable disconnection, power off, and so on).

21 ◄ (Backward) Press to shift the display right (the LCD display only shows 13 cross-points out of a total of 32).

1, 2, 3, 4, 5, 6, 7, 8, 9, 0

Numeric keypad, 1 to 0.

► (Forward)

Press to shift the display left (the LCD display only shows 13 cross-points out of a total of 32).

# Feature Function

AC Mains Power Module

Fuse holder and power cord socket. Connect to the AC mains supply.

RESET Button

Press to restart the VS-3232DN-EM.

26 USB Virtual Comm Port Mini USB

Connector

Connect to a computer to communicate with the unit and to upgrade the firmware of the

control card and compatible input/output cards.

27 IN 1~16 Connectors INPUTS Connect to the relevant video sources, depending on the cards installed (1 to 16).

IN 17~32 Connectors

Connect to the relevant video sources, depending on the cards installed (7 to 32).

TEST Module

Signal generator module for testing video outputs.

30 RESOLUTION DIP-switches Set the resolution for video generated by the Test module.

31 RS-232 9-pin D-sub Port Connects to the remote operation PC or remote controller.

32 NET Ethernet RJ-45 Connector Connect to a PC or controller via the Ethernet LAN.

The LINK LED flashes when communication is active. The POWER LED

lights when the

interface receives power.

OUT 1~16 Connectors

OUTPUTS

Connect to the relevant video acceptors, depending on the cards installed (1 to 16).

34 OUT 17~32 Connectors Connect to the relevant video acceptors, depending on the cards installed (17 to 32).

35 PATTERN Button Press the button repeatedly to change the video pattern generated by the Test module.

36 Test Module DVI Molex 24-pin Video

Connector

Connect to one of the relevant video inputs/outputs to aid in troubleshooting.

Step 3: Install the VS-3232DN-EM

To rack mount the machine, the

VS-3232DN-EM

is pre-assembled with ear brackets attached.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-3232DN-EM. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the VS-3232DN-EM.

Port Numbering:

All cards (except DVI dual link

cards) have four physical ports.

Numbering of ports is sequential

from top to bottom and left to right.

Each DVI dual link card provides

two physical ports which causes the

loss of two numbers in the

numbering sequence of that card

only.

Note:the maximum number of

ports may vary.

Diagram #

Actual Port #

1 IN 1, IN 2, IN 3, IN 4

IN 5, IN 6

3 IN 9, IN 10, IN 11, IN 12

OUT 1, OUT 2, OUT 3, OUT 4

5 OUT 5, OUT 6, OUT 7, OUT 8

OUT 9, OUT 10

Note: There is no IN 7, IN 8, OUT 11 or OUT 12

because these slots contain DVI dual link cards.

Step 5: Connect the power

Connect the AC power cord to the rear of the VS-3232DN-EM, switch on its power and then switch on the power of connected

devices.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Set operation parameters

The VS-3232DN-EM does not have separate output and input

buttons. Instead, the front panel includes a numeric keypad.

When the unit is powered-on, the last matrix setup that was

used is loaded. Use either the setup recall (records a stored

configuration from a preset) or default setup recall (for quick

retrieval of a commonly used programmable default setup)

functions to retrieve other setups.

The LCD display can show only 13 out of the 32 available matrix

combinations at once. To view any of the matrix combinations

use the ◄ or the ► buttons on the front panel to shift the display

to the right or left.

After switching on the power, the LCD display shows the following screens

in sequence:

Step 7: Operate via the front panel buttons, remote control, and via the:

RS-232 and Ethernet:

RS-232

Protocol 3000

Baud Rate: 9600

Data Bits: 8

Stop Bits: 1

Parity:

None

Command Format:

HEX

P3000, to switch Input 4 to Output 2:

#AV 4>2

Ethernet

IP Address: 192.168.1.39

TCP Port #: 5000

UDP Port #: 50000

Concurrent TCP Connections: 32

Full Factory Reset

Front Panel:

Press MENU twice. Select Total Matrix Reset > Factory default. Press TAKE twice.

EDID

EDID data is passed between Output 1 and Input 1

Autres manuels pour VS-3232DN-EM

Autres manuels Kramer Commutateur matriciel

Kramer

Kramer VS-6EIII Manuel utilisateur

Kramer

Kramer VP-4x4K Manuel utilisateur

Kramer

Kramer VS-44H Manuel utilisateur

Kramer

Kramer XL 1204V2 Manuel utilisateur

Kramer

Kramer XL 1208V2S Manuel utilisateur

Kramer

Kramer VS-1202YC Manuel utilisateur

Kramer

Kramer XL 1608V2 Manuel utilisateur

Kramer

Kramer VS-1616D-MD Manuel utilisateur

Kramer

Kramer VP-1608 Manuel utilisateur

Kramer

Kramer 3232S Manuel utilisateur

Kramer

Kramer VS-88UT Manuel utilisateur

Kramer

Kramer VS-3232Vxl Manuel utilisateur

Kramer

Kramer VS-169TP Manuel utilisateur

Kramer

Kramer VP-772T Manuel utilisateur

Kramer

Kramer XL 1204V4S Manuel utilisateur

Kramer

Kramer VS-84HN Manuel utilisateur

Kramer

Kramer VS-88UHDA Manuel utilisateur

Kramer

Kramer VS-3232A Manuel utilisateur

Kramer

Kramer VS-6464DN-EM Manuel utilisateur

Kramer

Kramer Sierra Viddeo 84V3S Manuel utilisateur

Kramer

Kramer VS-4216 Manuel utilisateur

Kramer

Kramer VS-42HDMI Manuel utilisateur

Kramer

Kramer VS-44HDCP Manuel utilisateur

Kramer

Kramer VS-1616AD Manuel utilisateur

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Roland

Roland XS-1HD Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes

Lindy

Lindy 38042 Manuel utilisateur

Extron electronics

Extron electronics MTPX Plus Series Manuel utilisateur

Key Digital

Key Digital Champion KD-16x16CS Manuel utilisateur

Shinybow USA

Shinybow USA SB-8811 Manuel utilisateur

Optimus

Optimus Compact Manuel utilisateur