Kohler K-97260X Instructions de montage

Installation and Care Guide

Dual System Bath





K-97260X

Thank You for Choosing Kohler Company

Building materials and wiring should be routed away from the pump body and other heat-producing components

of the unit.

A pressure wire connector marked “Earth/Ground” is provided within the wiring compartment. To reduce

the risk of electric shock, connect this connector to the grounding terminal of your electric service or supply

panel with copper wire equivalent in size to the circuit conductor supplying this equipment.

Grounding is required. The unit should be installed by a qualied service representative, and grounded.

NOTE: Install to permit access for servicing.

NOTICE : Follow all local plumbing and electrical codes.

B. Factory-Assembled Features

Your bath has been manufactured to the highest possible standard, it has been factory tested and approved.

WARNING : Unauthorized modication may cause unsafe operation or aect performance of the bath

with airjets. Do not relocate the blower motor, or make other modications to the system in the absence of

kit instructions, as this could adversely aect the performance and safe operation of the bath with airjets.

Kohler Thailand shall not be liable under its warranty or otherwise for personal injury or damage caused

by any such unauthorized modication.

We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before

you start installation. If you encounter any installation or performance problems, please call 0-2204-6222 for

Call Center (Thailand). Thank you again for choosing Kohler Company.

Important Information

IMPORTANT SAFETY INSTRUCTION

□ Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all operating and safety instructions.

□ All information is based on the latest product information available at the time of publication. Kohler Co.

reserves the right to make changes in product characteristics, packaging, or availability at any time without notice.

□ These instructions contain important care, cleaning, and warranty information, please leave these instructions

for the consumer.

A. InstallationHazardNotication

DANGER : Risk of re, electric shock, or injury to persons. Read important safety instructions included

in these instructions.

WARNING : Risk of electrical shock. A licensed electrician should make all electrical connections.

WARNING : Risk of electrical shock. Disconnect power before servicing.

WARNING : Risk of injury or property damage. Please read all instructions thoroughly before beginning

installation, including the following product requirements.

DANGER : Risk of electric shock. Connect only to circuits protected by a Ground-Fault Circuit-Interrupter

(GFCI) or Earth-Leakage Circuit-Breaker (ELCB).

1241693-X2-B 2 Kohler Co.

Tools

Before You Begin

Product Requirement

CAUTION : Risk of product damage. Do not lift the bath by the piping or pump, or use the piping or pump

for structural support of the bath.

□ We recommend this bath for drop-in.

□ Inspect the bath for damage before you begin installation.

□ You must install this bath to an adequately supported, level suboor.

□ Conrm adequate support for a rim-mounted faucet, large faucets that may be inadvertently used as a means

of support are not appropriate or safe for this installation.

Plus:

• Conventional woodworking or

concrete installation tools and materials

• Drop cloth

Silicone Sealant Measuring Tape LevelPencil

Pipe WrenchSafety Glasses

A. Summary of Key Requirements

□ Observe all local plumbing codes.

□ Install the unit to a level suboor.

□ Provide properly-dimensioned framing.

B. PlumbingSpecications

If using a rim-mounted bath faucet, exible connections between the valves and spout may be required. Conrm

adequate mounting, connection space of specied faucet for your installation.

C. Product Inspection

Carefully unpack and inspect the bath with airjets for damage. Leave all materials in the carton during constructions

to prevent damage.

D. Electrical Requirements

The installation must have a Earth-Leakage Circuit-Breaker (ELCB). The ELCB protects against Line-to-ground

shock hazard. Use a 220-240 V, 20 A (minimum), 50/60 Hz dedicated service for the bath with airjets.

E. Connections and Service Access

Before installation, ensure proper access to the nal connections.

NOTICE : Provide generous, unrestricted service access to the pump. You must provide access for servicing

the pump and controls. The access must be located immediately next to the pump. Study the roughing-in

information packed with the whirlpool (the size of access panel should not less than 500 x 450 mm).

Kohler Co. 3 1241693-X2-B

CAUTION : Risk of product damage. Do not support the bath by the rim.

Prepare the Site

Concrete Construction

NOTICE : Adequate oor support must be provided. Consult the roughing-in sheet packed with your bath for

specic oor loading requirements.

NOTICE : Unless otherwise specied, oor support under the bath must provide for a minimum 390 kg/square

meter loading.

NOTICE: Provide adequate ventilation and a minimum of 15 cubic feet (0.4 cubic meters) in the installed location

for cooling the motor and to supply sucient air for the blower. Do not install the blower motor closer than 2.5 mm

from the wall or other objects.

□ Make sure the ooring oers adequate support for your bath, and verify that the suboor is at and level.

□ This bath may be installed next to the wall or in an island installation. An island installation requires a four

side surround. In both instances, make sure the deck is supported by brick or concrete.

□ Install an access panel to allow the pump to be serviced.

□ Construct brick or concrete supports.

□ Provide 2 mm gap between the bath rim and the concrete or brick framing. Frame the oor, or construct

a frame for a raised installation, in accordance with the roughing-in information packed with the bath.

□ Position the plumbing according to the roughing-in information packed. Cap the supplies, and check for leaks.

Typical

Access

Panel

Whirlpool may be installed next to

the wall or as an island installation.

Install an access panel to allow

the pump to be serviced.

Bath

2 mm

Approved

Tile Backing

Approved

Tile Backing

Tile

Brick

Tile Brick

1/2" Water Supply

Power Supply

300-400

Ø2" Outlet

1500

500-700

1241693-X2-B 4 Kohler Co.

CAUTION : Risk of product damage. Do not lift the bath by the piping or pump, or use the piping or pump

for structural support of the bath.

Bath Installation

Prepare the Bath

□ When removing bath. Do not lift bath by pipe work. Inspect for any possible damage that may have occurred

in transit.

□ Insert the drain tailpiece into the trap. Make sure the bath is level. Use silicone to seal between drain and trap.

□ Seal the joint between the bath rim and the nished tiled wall using silicone sealant.

□ Ensure adjustable feet are ed through holes drilled in support frame.

□ Locate bath in proposed position. The protect lm originally covering your spa has been recovered to t its

equipment, therefore, carefully protect its surface during installation.

□ Make sure the bath is level (and resting on all support blocks).

□ Install the drain to the bath according to the drain manufacturer’s instructions. Do not connect the trap

at this time.

□ To adjust the height, loosen the nut A, adjust the height by tightening the nut B, and then tighten the nut A.

□ Position the bath on the support, adjust the level.

Bath rim must be fully supported.

560-600 mm

Bath

Pipe

Adjust and lock to recommended height.

Adjust the nut A to lock/unlock

the adjustable feet.

Adjust the height of the bath

by tightening the nut B.

Bath must be installed level on all top edges.

Plumbing Installation

NOTE : An access panel will simplify future maintenance.

□ Connect the drain to the trap according to the drain manufacturer’s instructions.

□ Open the hot and cold water supplies, and check the supply connections for leakage.

□ Run water into the bath, and check the drain connections for leakage.

CAUTION : Risk of product damage. Ensure a watertight seal on the bath drain.

Kohler Co. 5 1241693-X2-B

WARNING : Risk of electric shock. Make sure the power has been disconnected before performing the

following procedures.

WARNING : Risk of re, electric shock, or injury to persons. Be sure to insert the grounding pin of the

power cord plug in to the grounding contact of the electrical outlet or power strip and make sure it works.

Improper insertion, no insertion or noneective grounding can result in eletric shock, re of damage to

your bath

Make Electrical Connection

□ The whirlpool controls and system have been prewired at the factory. A licensed electrician must install ELCB

(Earth-Leakage Circuit-Breaker).

□ Provide a separate equipment earthing conductor for the earth lug located inside the junction box. The earthing

conductor must not be connected to any current-carrying conductor. Follow local electrical codes. Bond in

accordance with national and local codes.

EControl Box

Power Supply

LINE

LOAD

OFF

2 P

20 A

120-240V

50/60 Hz

SENSITIVITY 15 mA OPERATING TIME MAX. 0.1s

TEST

BUTTON

LEAKAGE

INDICATOR

INPUT

OUTPUT

DANGER : Risk of re, electric shock, or injury to persons. To reduce the risk of electric shock, connect

the pump to a properly grounded Earth-Leakage Circuit-Breaker (ELCB). This will provide additional

protection against line-to-ground shock hazard. A 220 - 240 V, 20 A, 50/60 Hz dedicated circuit is required.

WARNING : Risk of re, electric shock, or injury to persons. When using electrical products, basic

precautions should always be followed, including the following:

The above units must be connected by a registered electrician.

IMPORTANT : Access to power connections must be provided and must comply with local authority regulations.

Earth-Leakage Circuit-Breaker (ELCB) Connection

1241693-X2-B 6 Kohler Co.

Air Blower Connection

Assemble nozzle connection onto blower.

IMPORTANT : Maximum standard length of exible blower hose 1.5 metres. If blower installation is greater

than specied distance then an extension kit will be required

NOTE : Hose connection to manifold is factory ed.

□ Push the rubber cu onto blower nozzle and secure in position with hose clip.

□ Connect the blower to the control box.

Hose Clip

Connector

Rubber Cuff

Flexible Hose

Manifold

Push rubber cuff onto blower nozzle

and secure in position with hose clip.

Connect the blower to the control box.

Maximum Distance 1.5 metres

Kohler Co. 7 1241693-X2-B

ConrmProperOperation

NOTE : Please read these steps carefully before you operate your dual system bath.

(refer to the “Switch Function and Operation” section)

□ Check all electrical connections, and make sure the electrical power to the whirlpool is turned on.

□ Make sure all union connections to the pump and heater are securely hand tightened.

□ Position the jet nozzles so they face down toward the basin. Turn the jet trim ring fully counterclockwise.

□ Fill the bath to a level above the top of the higher jet around 40 mm.

□ Press the Power On/O buon to turn on the whirlpool. The whirlpool will start at medium ow. Check all

bath piping connections, on the back side, for leaks.

□ Turn the jet trim clockwise to decrease the ow, and counterclockwise to increase the ow

□ Press the Power On/O buon a second time to turn the bath o.

NOTE : The water temperature in the bath should not exceed 40° C (104° F). The heater will automatically turn o

as the water temperature approaches 40° C (104° F), and will remain o until the water cools.

Complete the Brick

□ Cover the constructed brick with cement. Seal the joints between the bath rim edge and the brick with silicone

sealant.

□ Cover the outer side of the constructed brick with tiles. Seal the joints between the bath rim and tile with silicone

sealant.

Cement

Brick

Bath

Wall

Finished Material

Apply Silicone Sealant

Turn the jet trim ring counterclockwise

to increase the ﬂow.

Turn the jet trim ring clockwise

to decrease the ﬂow.

Fill with water (40 mm) above the highest jet.

Position the jet nozzles to direct

the water ﬂow as desired.

Pop-Up Drain Control Knob

Turn counterclockwise

to close the pop-up drain.

Turn clockwise to

open the pop-up drain.

1241693-X2-B 8 Kohler Co.

Switch Function and Operation

IMPORTANT : If the running system cannot detect the presence of water level (power indicator ashes in green),

the motor / heater / pump will shut o automatically.

A. Light Indicators

B. Air Massage Operation

Power

Water

Fault

ON/OFF

AUTO SANITISING CYCLE

OSCILLATING CYCLE-PRESS BOTH

Power available indicator

Red light indicates power available to control box and electronic switch.

Water level indicator

Fill bath with water ensuring that the water level 40mm above spa jets.

After you press Motor pump / heater on/o, the water level indicator

will light in green.

Fill the bath with warm water ensuring that the water level is 40 mm

above spa jet. Press on/o buon.

To increase Air Blower speed: press until desired speed reached.

To decrease Air Blower speed: press until desired speed reached.

Press both switches together for Auto High-Low cycle (Wave Action).

Press on/o buon.

Power

Water

Fault

Indicator lights in red

Power

Water

Fault

Indicator lights in green

ON/OFF

Turning off

ON/OFF

Turning on

High Speed

Low Speed

Oscillating cycle

Kohler Co. 9 1241693-X2-B

1st push

Motor Pump on / Heater on.

2nd push

Motor Pump on / Heater o.

3rd push

Motor Pump o / Heater o.

D. Air Bubble Volume Control

Turn the knob clockwise to increase air bubble volume and turn counterclockwise to decrease air bubble volume in

whirlpool system.

Switch Function and Operation (Cont.)

C. Motor Pump/Heater On/Off Control

Allows bather to switch o the heater when not required.

E. Auto Sanitising Cycle

Auto clean up cycle will commence 20 minutes after the bath has been emptied of water. The blower and heater

will then restart and operate for 2 minutes sanitising the system with hot air before automatically shuing down.

F. Auto Timer

The auto safety timer will shut the air/spa system down automatically after 30 minutes of continual operation,

and can be restarted again by pressing the electronic ON/OFF switch.

IMPORTANT : Air spa system will only operate for 5 seconds if insucient water level is detected, automatically

shuing down.

G. Leakage Detection

Leakage Detection indicator

When the fixture is powered on and the bath has run out of water,

press Blower Speed Decrease buon, Blower Speed Increase buon and

Motor/Pump-Heater buon simultaneously for more than 3 seconds to

create a simulation of electricity leakage, then the indicator will ash in

red and green alternatively. This indicates the leakage detection function

is well in use, otherwise, there’s possibility that this function fails to

operate normally and may result in electric shock accident.

Release three buons and the bath will not function anymore if any key

is pressed. Make the bath powered-on again and the bath will restore its

function.

Power

Water

Fault

Indicator ﬂashes in red

and green alternatively.

Indicator lights in red

Indicator lights in blue

Indicator turns off

Turn counterclockwise to decrease

air bubble volume in whrilpool

Turn clockwise to increase

air bubble volume in whirlpool

1241693-X2-B 10 Kohler Co.

Table des matières

Langues :

Autres manuels Kohler Baignoire

Kohler

Kohler K-1159-L Guide de démarrage rapide

Kohler

Kohler K-1170-H2 Instructions de montage

Kohler

Kohler K-1101-S Manuel utilisateur

Kohler

Kohler System II K-712-H Manuel utilisateur

Kohler

Kohler EVOK 2.0 25163A-0 Manuel utilisateur

Kohler

Kohler Underscore K-1822-GVB Manuel utilisateur

Kohler

Kohler Underscore Cube K-1969-VB Guide de l'utilisateur

Kohler

Kohler K-870 Instructions de montage

Kohler

Kohler K-1339-H2 Instructions de montage

Kohler

Kohler Iron Works Tellieur K-727 Instructions de montage

Kohler

Kohler Windward K-1114-L Guide de démarrage rapide

Kohler

Kohler BIRTHDAY BATH Manuel utilisateur

Kohler

Kohler K-1124 Manuel utilisateur

Kohler

Kohler K-790 Instructions de montage

Kohler

Kohler K-792 Manuel utilisateur

Kohler

Kohler Mira Flight Freestanding Bath Manuel d'utilisation

Kohler

Kohler Archer K-2595-G Manuel utilisateur

Kohler

Kohler K-1112-GLF Guide de démarrage rapide

Kohler

Kohler K-1477 Instructions de montage

Kohler

Kohler K-1239-H Guide de démarrage rapide

Kohler

Kohler K-1947-XHGL-33 Instructions de montage

Kohler

Kohler K-1800X Instructions de montage

Kohler

Kohler Underscore K-5716-GCR Manuel utilisateur

Kohler

Kohler K-1108-LA Instructions de montage

Manuels Baignoire populaires d'autres marques

Agua

Agua BARTOLI-66 Manuel utilisateur

PAA

PAA PRELUDE Manuel utilisateur

BETTE

BETTE SILHOUETTE Manuel utilisateur

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Manuel utilisateur

Oliveri

Oliveri Naples Manuel utilisateur

Lyons

Lyons Elite ETLxx663219 Series Manuel utilisateur

Woodbridge

Woodbridge BJ500 Instructions de montage

Whirlpool

Whirlpool Ariel ARL-702 Manuel utilisateur

TEIKO

TEIKO EXCELLENT DUO Manuel utilisateur

American Standard

American Standard Colony 5-1/2' x 32" Manuel utilisateur

American Standard

American Standard 3052OD.X0X Guide de démarrage rapide

agape

agape MARSIGLIA AVAS1075 Manuel utilisateur

Kallista

Kallista P50045-G5 Instructions de montage

Ariel

Ariel AM Series Manuel utilisateur

Agua

Agua BAHLI-60 Manuel utilisateur

DURAVIT

DURAVIT XViu 700443 Manuel utilisateur

American Standard

American Standard Colony 2740 Series Manuel utilisateur

Rapsel

Rapsel OFURO Manuel