Knick Stratos Pro A201N-CC Manuel utilisateur

User Manual Stratos Pro A201N-CC

Dual Conductivity Measurement

Read before installation.

Keep for future use. www.knick.de

Supplemental Directives

Read this document and retain it for future reference. Before assem-

bling, installing, operating, or maintaining the product, ensure that

you fully understand the instructions and risks. Observe all safety

instructions. Failure to follow the instructions in this document may

result in serious injury and/or property damage.

This document is subject to change without notice.

These supplemental directives explain how safety information is laid

out in this document and what content it covers.

Safety Chapter

This document's Safety chapter is designed to give the reader a basic

understanding of safety. It illustrates general hazards and gives strate-

gies on how to avoid them.

Safety Guide

The external Safety Guide is designed to give the reader a basic

understanding of safety. It illustrates general hazards and suggests

strategies on how to avoid them.

Warnings

This document uses the following warnings to indicate hazardous

situations:

Symbol Category Meaning Remark

WARNING Designates a situation that can lead to death or

serious (irreversible) injury.

The warnings

contain information

on how to avoid

the hazard.

CAUTION Designates a situation that can lead to slight or

moderate (reversible) injury.

None NOTICE Designates a situation that can lead to property

or environmental damage.

Additional Safety Information

Stratos Safety Guide

Documents Supplied

Safety Guide

In ocial EU languages and others

Quickstart Guides

Installation and rst steps:

• Operation

• Menu structure

• Calibration

• Error messages and recommended actions

Test Report 2.2 According to EN 10204

Electronic Documentation

www.knick-international.com:

Manuals + software

Table of Contents

Supplemental Directives............................................................... 2

Documents Supplied ..................................................................... 3

Safety ................................................................................................ 6

Always Read and Observe the Safety Instructions!................. 6

Intended Use ......................................................................................... 6

Introduction .................................................................................... 8

Overview of Stratos Pro A201N-CC...........................................10

Assembly........................................................................................11

Package Contents ..............................................................................11

Electrical Installation ...................................................................15

Rating Plates / Terminal Assignments........................................16

Wiring of Stratos Pro A201N-CC...................................................17

Wiring Examples.................................................................................18

User Interface, Keypad ................................................................21

Display............................................................................................22

Signal Colors (Display Backlighting)...........................................22

Measuring Mode...........................................................................23

Selecting the Mode / Entering Values......................................24

Color-Coded User Interface........................................................26

Operating Modes..........................................................................27

HOLD Mode .........................................................................................29

Alarm ......................................................................................................30

Alarm and HOLD Messages............................................................31

Configuration ................................................................................32

Menu Structure of Configuration.................................................32

Setup and Channel Selection on the Device ..........................33

Calculations (CALC) ......................................................................34

Calculating the pH Value by Means of Dual Conductivity

Measurement ......................................................................................36

Table of Contents

Configuration (Template for Copy)...........................................42

Configuring Sensors A, B.................................................................44

Current Output 1................................................................................48

Current Output 2................................................................................56

CONTROL Input (TAN SW-A005) .....................................................58

Alarm Settings.....................................................................................60

Time and Date.....................................................................................62

Measuring Point (TAG) ....................................................................64

Display Backlighting .........................................................................64

Calibration .....................................................................................66

Calibration by Input of Cell Factor...............................................67

Measurement ................................................................................68

Diagnostics ....................................................................................69

Service ............................................................................................74

Operating States...........................................................................77

Supply Units and Connection ....................................................78

Product Line and Accessories ....................................................79

Specifications ................................................................................80

Error Handling...............................................................................84

Error Messages..............................................................................85

Decommissioning.........................................................................87

Disposal .................................................................................................87

Returns...................................................................................................87

Sensocheck and Sensoface ........................................................88

HART: Typical Applications.........................................................90

FDA 21 CFR Part 11 ......................................................................91

Electronic Signature – Passcodes.................................................91

Audit Trail..............................................................................................91

Index ...............................................................................................92

Safety

Always Read and Observe the Safety Instructions!

The device is constructed in accordance with the latest technology

and generally accepted safety rules and regulations.

Under certain circumstances, however, usage may pose risks to users

or cause damage to the device.

Commissioning must be carried out by specialist personnel authorized

by the operating company. If safe operation is not possible, the device

must not be switched on or, if it is already on, must be switched o

properly and secured against unintended operation.

Reasons to assume safe operation is not possible:

• the device shows visible damage

• failure to perform the intended function

• prolonged storage at temperature of below -30°C/-22°F or above

70°C/158°F

• severe transport stresses

Before recommissioning the device, a professional routine test must

be performed. This test should be carried out by the manufacturer at

its factory.

Intended Use

Stratos Pro A201N-CC is a 2-wire device for two-channel measurement

of electrical conductivity and temperature in liquids. The device has

been designed for measurements before and after cation exchangers

using commercial analog 2-electrode sensors. Dierent parameters

can be calculated from the two conductivity values, e.g. dierence,

ratio, rejection, but also the pH value of feed water.

The dened rated operating conditions must be observed when using

this product. They can be found in the Specications chapter of this

User Manual; see page 80.

Safety

Function Check Mode (HOLD Function)

After activating conguration, calibration, or service, StratosPro

enters function check mode (HOLD).

The current outputs respond in accordance with the conguration.

Operations must not be carried out while StratosPro is in function

check(HOLD) mode, as the system may behave unexpectedly and put

users at risk.

Devices Not Intended for Use in Hazardous Locations

Devices identied with an N in their product name must not be used

in hazardous locations.

Conguration

Replacing components may aect intrinsic safety. The modules

are not intended to be replaced on devices in the Stratos Pro A201

product line.

Housing and Mounting Options

• The sturdy molded enclosure is designed for IP66/IP67/ TYPE4X

Outdoor protection, is made of PBT glass ber reinforced PC, and

has the following dimensions: H148mm, W148mm, T117mm.

Knockouts in the housing enable

• wall mounting (with sealing plugs to seal the housing)

see page 12

• pipe mounting (Ø 40 … 60 mm, 30 … 45 mm)

see page 13

• panel mounting (cutout 138 mm x 138 mm acc. to DIN43700)

see page 14

Protective Hood (Accessory)

The protective hood, which is available as accessory, provides ad-

ditional protection against direct weather exposure and mechanical

damage; see page 13.

Connection of Sensors, Cable Glands

For connecting the cables, the enclosure provides

• 3 knockouts for M20x1.5 cable glands

• 2 knockouts for ½” conduit

Display

Plain-text messages on a large, backlit LC display enable intuitive op-

eration. You can specify which values are to be displayed in standard

measuring mode (“Main Display,” see page 25).

Color-Coded User Interface

The colored display backlighting indicates dierent operating states

(e.g., alarm: red, HOLD mode: orange; see page 26). The display

backlighting can be switched o; see page 64.

Introduction

Diagnostic Functions

“Sensocheck” automatically monitors sensor and cables; and the

“Sensoface“ function clearly indicates the sensor condition; see

page88.

Data Logger

The internal logbook (TAN SW-A002) can handle up to 100 entries –

upto 200 with AuditTrail (TAN SW-A003); see page 72.

Password Protection

Password protection (passcodes) for granting access rights during

operation can be congured; see page 76.

TC Process Medium: Selecting the Compensation Method

The following temperature compensation methods are provided:

linear (by entering a temperature coecient), natural waters (nLF),

ultrapure water with traces of NaCl, HCl, NH3, NaOH, see page 44.

Control Inputs (TAN SW-A005)

The oating, digital control input “HOLD“ allows remote controlled

switching to HOLD mode. The “CONTROL“ input allows evaluation of

external monitoring equipment, such as a ow monitoring system.

For that purpose, you can also monitor the current input for keeping a

desired value.

Signal Outputs

The device provides two current outputs (for transmission of

measured value and temperature, for example). The output curve is

adjustable (linear or bilinear), see page 48.

Options

Additional functions can be enabled by entering a TAN (p. 76).

Overview

Overview of Stratos Pro A201N-CC

Output 1

Output 2

RS 485

Current

input

HOLD

input

CONTROL

input

ACC

input

Table des matières

Autres manuels Knick Instrument de mesure

Knick

Knick Stratos Pro A4..MSPH series Manuel utilisateur

Knick

Knick Protos 3400X Manuel utilisateur

Knick

Knick Stratos Pro A*** COND Series Manuel utilisateur

Knick

Knick Portavo 904 COND Manuel utilisateur

Knick

Knick Stratos PROFIBUS 2222X CondI Manuel utilisateur

Knick

Knick Protos 3400X Manuel utilisateur

Knick

Knick Protos 3400X Manuel utilisateur

Knick

Knick Stratos Pro A2 COND Series Manuel utilisateur

Knick

Knick Stratos Pro A2 COND Series Manuel utilisateur

Knick

Knick SensoGate WA 131 H Manuel utilisateur

Knick

Knick Stratos PROFIBUS 2221X Cond Manuel utilisateur

Knick

Knick Protos II 4400 Manuel utilisateur

Knick

Knick Stratos Eco 2405 Oxy Manuel utilisateur

Knick

Knick Portavo 904X COND Manuel utilisateur

Knick

Knick Protos II 4400 Manuel utilisateur

Knick

Knick PORTAVO 904X PH Manuel utilisateur

Knick

Knick Protos CONDI 3400(X)-051 Manuel utilisateur

Knick

Knick Protos 3400X Manuel utilisateur

Knick

Knick ARD 50 Manuel utilisateur

Knick

Knick Stratos MS A405 Manuel utilisateur

Knick

Knick Stratos Pro A2 PH Series Manuel utilisateur

Knick

Knick Stratos Eco 2405 Cond Manuel utilisateur

Knick

Knick Protos 3400 Instructions originales

Knick

Knick Stratos Eco 2405 CondI Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur