Kicker 48BTCAN65 Manuel utilisateur
1English
Contents
Overview........................2
Package Contents:................ 2
Specifications........................ 3
Installation ......................5
Power & Auxiliary Wiring......... 5
Switch Install ......................... 6
LED Grille Wiring.................... 7
Speaker Wiring...................... 7
Mounting............................... 9
Operation.....................11
Multi-Function Button........... 11
Status LED.......................... 12
Setting Input Source ............ 13
Line Output & AUX IN .......... 13
Remote Control Install.......... 14
Remote Control Operation ... 16
Troubleshooting............17
Warranty ......................18
Int. Warranty.................71
2English
Overview
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR
SUBWOOFER IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER
CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING
FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS
AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1
INCH (2.5CM) CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND
ANY SURFACE. KICKER PRODUCTS ARE CAPABLE OF PRODUCING SOUND
LEVELS THAT CAN PERMANENTLY DAMAGE YOUR HEARING! TURNING UP A
SYSTEM TO A LEVEL THAT HAS AUDIBLE DISTORTION IS MORE DAMAGING
TO YOUR EARS THAN LISTENING TO AN UNDISTORTED SYSTEM AT THE
SAME VOLUME LEVEL. THE THRESHOLD OF PAIN IS ALWAYS AN INDICATOR
THAT THE SOUND LEVEL IS TOO LOUD AND MAY PERMANENTLY DAMAGE
YOUR HEARING. PLEASE USE COMMON SENSE WHEN CONTROLLING
VOLUME.
The PowerCans are the next generation in mobile
audio systems, combining the innovations of new
transfer protocols with KICKER’s finest speaker and
amp performance. This audio system has everything
you need ready to roll right out of the box. Bluetooth
5.0 and AUX Input, integrated amplifier, RGB lighting,
line output, and a wired remote control built to mount
in a standard marine panel. And at its heart, the high-
powered amp and 6.5” speakers pack a punch with
KICKER signature quality audio.
Use the following instructions to install and operate
your PowerCan and PowerCan Remote.
Package Contents:
(4) M6*14 Screws (8) Washers for mounting rings
(4) M8*16 Screws (4) Washers for mounting base
(2) 1.5” Round Rings (2) 1.75” Round Rings
(2) 2” Round Rings (2) Mounting Bracket Base
(2) 6-inch Rubber Strips for mounting rings
(1) RGB LED Pigtail (1) Ring Terminal – Black
(1) Wired Remote Control
(1) Fuse Accessory Wire with 15A ATC fuse
3English
Model: BTCAN65
Power Output
@ 14.4V, <10% THD+N
75W x 2
Height [in, mm] 6-5/8, 168
Width [in, mm] 6-5/8, 168
Depth [in, mm] 7-7/8,200
Weight [lbs, kg] 13.6, 6.2
Woofer [in, mm] 6-1/2, 160
Tweeter [in, mm] 1, 25
Wiring Harness Length [ft, m] 12, 3.66
Frequency Response [Hz] 80-20K
Signal-to-Noise Ratio >102, A-weighted,
re: rated power
Tweeter Magnet Material Neodymium
Tweeter Dome Material Titanium
Tweeter Design Dome
Woofer Cone Material Polypropolene
Woofer Surround Material Santoprene
Aux Input Stereo 3.5mm Female
1.0 V Sensitivity
Line Output Stereo 3.5mm Female
Buffered, 1V
Specifications
4English
Primary
(Right)
Secondary
(Left)
5English
Installation
Power & Auxiliary Wiring
Disconnect the vehicle’s battery to avoid an electrical
short. Run the black ground wire to a paint-and-
corrosion-free, solid, metal area of the vehicle’s
chassis or the negative battery terminal. Crimp the
provided 5/16” ring terminal to the ground wire. The
ring terminals have been left off so that power and
ground wires may be run through vehicle tubing. Do
not install the ring terminals until all wires have been
run to their final location.
Run the yellow +12V constant wire to the battery
location. Crimp the provided 15A ATC fuse to
the yellow wire, which includes a heat-shrink butt
connector. Once mechanically crimped, apply
heat to the connector to create a secure, insulated
connection. Then securely connect the fuse’s 5/16”
ring terminal to the positive battery terminal. Note that
while the ring terminals can be cut off if necessary,
the fuse should always be kept within 18 inches of
the battery.
6English
12V
15A ATC fuse
+12V
Ignition
(red)
+12V Constant
(yellow)
battery
wired
remote
ground
(black)
LINE OUT (1V,
3.5mm - grey)
AUX IN (1V,
3.5mm - black)
≤18”
(45cm)
Connect the Red +12V Ignition Wire to the switched
ignition power source, dash-mounted switch,
accessory or relay switch.
12V
Switch Install
If you’d like to use a switch to control power to your
PowerCan, wire it according to the following diagram.
battery
fuse
15A ATC
fuse
2A (sold
separately)
ground (black)
+12V Ignition (red)
+12V Constant (yellow)
7English
Speaker Wiring
The speaker wiring for the PowerCan comes pre-
installed with heat-shrink butt connectors on the
Right PowerCan for a fast and secure connection.
Connect the Right PowerCan’s speaker wire to the
left PowerCan’s speaker wire, then crimp and apply
heat.
Speaker wires
Speaker wires
LED Output &
Input wires
LED Grille Wiring
1. Connect the LED Output of the Right PowerCan
(female plug), located on the smaller wire loom, to the
LED Input (male plug) of the Left PowerCan.
2. To control LED Grille behavior, install the KICKER
KMLC (sold separately) by connecting the male LED
plug of the Right PowerCan, located on the larger
wire loom, to the KMLC female plug.
8English
12V
Ground
+12V
Switch 2A fuse ≤7”
(17.5cm)
battery
3. If you’re not using the KMLC, use the included
RGB Pigtail to hard-wire your LED. Connect the RGB
Pigtail to the male LED plug of the Right PowerCan.
When hard-wiring the LED lighting, the black lead is
+12V and the blue, red and green leads are ground.
Connect the black LED wire to the positive terminal of
the battery.
a. Place a 2-amp fuse (not included) no further than
7” away from the battery terminal.
b. Install a switch (not included) on the black LED
wire between the fuse and the speaker, so the LED’s
can be turned off. Without a switch to turn them off,
they will always be on.
Red Red
Green Green
Blue Blue
Red/Green Yellow
Red/Blue Magenta
Blue/Green Cyan
Red/Green/Blue White
Connect the red, blue and/or green LED wires to the
negative terminal of the battery. See the Venn diagram
below for available combinations.
Red
Yellow
Green BlueCyan
White
Magenta
9English
Mounting
The PowerCans mount out-of-the-box to round bars
with the included 1.5”, 1.75”, and 2” diameter Bar
Clamps. Use the KPB Square Clamps (47KPBSQ),
sold separately, to mount your PowerCans to square
bars. Choose a structurally sound location to mount
the PowerCans. The Mounting Base may be rotated
±30° to accommodate some curved bars. Make sure
there are no items interfering with the route of the
wiring. Installation tools are not provided. 5mm and
6mm Allen Wrenches are required. Using mounting
hardware, including clamps and screws, not
provided by KICKER will result in a voided
warranty.
1. Screw the Mounting Bases to the PowerCans
using the Mounting Screws.
±30°
6mm Allen
Wrench required
Table des matières
Langues :
Autres manuels Kicker Intervenants
Kicker
Kicker 41KPWB Manuel utilisateur
Kicker
Kicker KM44CW Manuel utilisateur
Kicker
Kicker Street Series Manuel utilisateur
Kicker
Kicker KSC350 Manuel utilisateur
Kicker
Kicker DS35 Manuel utilisateur
Kicker
Kicker KM4 Manuel utilisateur
Kicker
Kicker YJ-SPKUP Manuel utilisateur
Kicker
Kicker BT Cans Manuel utilisateur
Kicker
Kicker DSC4 Manuel utilisateur
Kicker
Kicker CSS65 Manuel utilisateur
Kicker
Kicker 48KSS269 Manuel utilisateur
Kicker
Kicker 41KM604W Manuel utilisateur
Kicker
Kicker KMTC9W Manuel utilisateur
Kicker
Kicker KM4 Manuel utilisateur
Kicker
Kicker PSC57 Manuel utilisateur
Kicker
Kicker KM10 Manuel utilisateur
Kicker
Kicker KPM50 Manuel utilisateur
Kicker
Kicker FKAVV09 Manuel utilisateur
Kicker
Kicker KM60 Manuel utilisateur
Kicker
Kicker KSS50 Manuel utilisateur
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur