Keysight Technologies CXA Manuel d'installation et d'exploitation

Option PRC - Portable Configuration

Keysight CXA/EXA/MXA Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9020-90133

Supersedes N9020-90044

Edition

Edition 1, April 2015

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9020-90133 3

Option PRC, Portable Configuration Installation Kit

Option PRC,

Portable Configuration Installation Kit

Introduction

This installation note is part of a retrofit kit that enables the installation of Option PRC, Portable

Configuration. This retrofit kit provides the bumpers and handle hardware needed to convert a

bench top signal analyzer into a portable signal analyzer.

CAUTION While the parts in this upgrade kit could also be installed onto a PXA N9030A

signal analyzer, this kit is NOT to be used with these instruments.

The bail handle for the portable configuration, and its attachment to the

instrument, has NOT been designed to support the added weight of the PXA

N9030A signal analyzer.

The use of this portable configuration upgrade kit with a PXA N9030A signal

analyzer, or any other unintended use, could result in either personal injury or

instrument damage.

Products Affected: CXA N9000A

EXA N9010A

MXA N9020A

Serial Numbers: All

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time: 0.5 Hours

N/A

4Installation Note N9020-90133

Option PRC, Portable Configuration Installation Kit

Contents

Tools Required

— T-20 Torx driver

—Smallflatheadscrewdriver

Quantity Description Keysight Part

Number

1 Installation Note This note

1 Trim Strip, Top with Bumper W1312-40004

4 Bumper Assembly, Front W1312-40020

4 Bumper Assembly, Rear W1312-40021

4 Hole Plug, Strap Handle W1312-40024

1 Cover, Impact W1312-40025

4 Hole Plug, Bottom Foot W1312-40032

1 Bail Handle Assembly W1312-60036

12 Screw M4 X 0.7 14 mm-LG 0515-0435

4 Screw M5 X 0.8 14 mm-LG 0515-5209

4 Screw M4 X 0.7 25 mm-LG Pan head 0515-1619

4 Washer, Flat 3050-0893

Installation Note N9020-90133 5

Installation Procedure

1. Refer to Figure 1. Locate and remove both strap handle assemblies (1) (N9020-60002). Each

handle is attached to the instrument case with two Torx 20 screws. Set aside the two strap

handle assemblies as they are no longer needed.

Figure 1 Strap Handle Removal

2. Locate four strap handle hole plugs (W1312-40024) and four screws (0515-5209) from the kit.

Install strap handle hole plugs and secure with screws. Torque to 21 in-lbs.

3. Locate and remove the four key locks (5021-2840) from the four instrument feet located on the

bottom of the instrument. Set aside the four key locks as they are no longer needed.

4. Locate and remove the four instrument feet (2) (5041-9167) located on the bottom of the

instrument. Set aside the four instrument feet as they are no longer needed.

5. Locate and remove the four rear feet (3) (5041-9611). Each foot is attached with one Torx 20

screw and a washer. Set aside the four rear feet, the four screws and the four washers as they

are no longer needed.

6Installation Note N9020-90133

Installation Procedure

NOTE 1. It is recommended that all of the parts that have just been removed be

stored away somewhere together in case you need to return the instrument to

the bench top configuration.

2. The screws attaching the four rear bumpers are what hold the instrument

cover in place. Once these have been removed, be careful not to disturb the

instrument cover placement as it is seated into the EMI gasketing in the front

frame. Also, removal or excessive movement of the instrument cover may

break any calibration or security seals that may have been placed on the

instrument.

6. Refer to Figure 2. Locate four rear bumper feet (1) (W1312-40021), four screws (0515-1619)

and four washers (3050-0893) from the kit. Install the rear bumper feet. Secure with screws

and washers. Torque to 21 in-lbs.

Figure 2 Rear Bumper Installation

7. Locate and install four foot hole plugs (2) (W1312-40032) from the kit.

Installation Note N9020-90133 7

Installation Procedure

8. Refer to Figure 3. Locate the top trim strip on the front panel. The top trim strip snaps into

place. Use a small flathead screw driver to remove the top trim strip as shown. Ensurethat you

do not scratch the front panel. Discard the top trim strip.

Figure 3 Top Trim Strip Removal

9. Refer to Figure 4. Locate and remove the adhesive side trim strips from both sides of the front

panel. Discard the side trim strips.

8Installation Note N9020-90133

Installation Procedure

Figure 4 Side Trim Strip Removal

10.Locate the top trim strip (W1312-40004) from the kit. Snap top trim strip into place in the

cavity on the top of the front frame.

11.Refer to Figure 5. Locate four front bumpers (1) (W1312-40020) and eight screws

(0515-0435) from the kit. Install front bumpers with long side facing forward. Secure each

front bumper with two screws. Torque to 21 in-lbs.

Installation Note N9020-90133 9

Installation Procedure

Figure 5 Front Bumper Installation

10 Installation Note N9020-90133

Installation Procedure

12.Refer to Figure 6. Locate Bail Handle assembly (1) (W1312-60036) and four screws

(0515-0435) from the kit. Adjust handle as shown. Snap handle into place on the instrument

front frame. Secure the Bail Handle assembly with screws. Torque to 21 in-lbs.

Figure 6 Bail Handle Installation

13.Locate Impact Cover (W1312-40025). This cover is used to protect the instrument front panel

during transport. Since it must be removed to use the instrument, you may or may not put it on

the instrument at this time depending on your need.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Keysight Technologies Instrument de mesure

Keysight Technologies

Keysight Technologies MXA N9020A-508 Manuel utilisateur

Keysight Technologies

Keysight Technologies X-Series Manuel utilisateur

Keysight Technologies

Keysight Technologies P5000A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N9030B Manuel utilisateur

Keysight Technologies

Keysight Technologies P939 A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies UXA N9040B Manuel utilisateur

Keysight Technologies

Keysight Technologies BT2152A Manuel de service

Keysight Technologies

Keysight Technologies B2901A Manuel utilisateur

Keysight Technologies

Keysight Technologies E5080B Manuel utilisateur

Keysight Technologies

Keysight Technologies N432A Manuel utilisateur

Keysight Technologies

Keysight Technologies N77 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies BT2152B Manuel de service

Keysight Technologies

Keysight Technologies U9361F Manuel utilisateur

Keysight Technologies

Keysight Technologies N9322C Manuel utilisateur

Keysight Technologies

Keysight Technologies U1281A Manuel utilisateur

Keysight Technologies

Keysight Technologies N1060A Manuel utilisateur

Keysight Technologies

Keysight Technologies N5251A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N5221B Manuel utilisateur

Keysight Technologies

Keysight Technologies E5072A Manuel utilisateur

Keysight Technologies

Keysight Technologies N8480 Series Manuel de service

Keysight Technologies

Keysight Technologies E4981A Manuel utilisateur

Keysight Technologies

Keysight Technologies N9020B Manuel d'installation et d'exploitation

Keysight Technologies

Keysight Technologies M9451A Guide de l'utilisateur

Keysight Technologies

Keysight Technologies N5224/5A Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur