Kentec Electronics S793 Manuel technique

4 Channel NAC Module (S793)

Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

CONTENTS

Contents 2

Compliance 4

Underwriters Laboratories (UL) 4

FCC 4

Installation 4

Introduction 5

Technical Support 5

Return Material Authorization (RMA) 5

Warranty Service 6

Advanced Replacements 6

Overview 7

Package Contents 7

Installation 9

Before You Begin 10

Setting the Address 10

Placement 11

Wiring 12

Circuits 12

Field Wiring 13

Testing the Installation 14

Configuration 15

NACModule Properties 15

Channel Properties 16

4 Channel NAC Module (S793) Information Guide

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 2

Pattern Output 17

Strobe Output 17

Power Output 17

ULCompliance Limitations 18

Troubleshooting 19

Specifications 22

Overall Module Electrical Ratings 22

Operating Environment 22

Physical Specifications 22

NAC Outputs 23

Regulated NAC Outputs 23

Special Application NAC Outputs 24

NACPower Output Modes 25

Connections for NACPower Output Modes 25

Continuous Constant Power 25

Door Holder 26

Resettable 26

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 3

4 Channel NAC Module (S793) Information Guide

COMPLIANCE

Underwriters Laboratories (UL)

Fire Alarm Subassembly

Kentec Electronics Ltd

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the Installation Manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense. Any

changes or modifications not expressly approved by Kentec Electronics Ltd could void the user's authority to

operate this equipment under the rules and regulations of the FCC.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

Installation

Install this product in accordance with NFPA 13, NFPA 72, NFPA 70, and NEC 70 and all local codes.

All field wiring should be installed using fire rated cables according to the NFPA 72. Riser conductors shall be

installed in accordance with the survivability from attack by fire requirements in National Fire Alarm Code, NFPA

72, Section 12.3. Riser conductors shall employ either a 2 hour rated cable system, or meet requirements

approved by the AHJ.

4 Channel NAC Module (S793) Information Guide

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 4

INTRODUCTION

Technical Support

For technical support, contact Kentec Electronics, Ltd at +44 (0)1322 222121 or techsupport@kentec.co.uk.

Prior to contacting technical support, have the following information available:

nProduct part number

nPurchase order or order number

nProduct serial number

nCurrent function of the product

nExpected function of the product

nInstallation of the product

Return Material Authorization (RMA)

Contact Technical Support to obtain an RMAfor any product to be returned. Returns will not be accepted

without an accompanying RMA number. An RMA number is assigned when:

lTech Support acknowledges a possible product failure.

lA product was damaged during shipping

lAn incorrect product was shipped

lAn order was placed using an incorrect part number *

lAn order was placed using an incorrect part quantity *

lAn order is no longer required *

* Restocking fees may apply.

All returned products are tested to confirm operating failures experienced in the field. If the product is found to be

functional, contractors must absorb expenses for return shipping, as well as the cost and shipping of the

advanced replacement product.

Prominently display the RMA number on all packages sent for return.

Ship all return products to:

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 5

4 Channel NAC Module (S793) Information Guide

Attention: RMA # _____________

Kentec Electronics, Ltd

Units 25-27 Fawkes Avenue

Questor, Dartford

Kent. DA1 1JQ

United Kingdom

Warranty Service

Technical Support can replace or repair a defective product when the original purchase is within the warranty

period defined in the sales contract. Check your contract for more information, or contact your sales

representative about your specific warranty period.

Advanced Replacements

Products that fail to operate in the field can be replaced quickly using the advanced replacement process. The

advanced replacement process is available to all contractors who maintain an acceptable line of credit.

Initiate the advanced replacement process by requesting an RMA number from a Tech Support representative.

Advanced replacements can be shipped to your location when the product is covered under warranty and when

a replacement product is in stock.

lAdvanced replacements can be expedited at the request of the contractor. Shipping costs associated with this

process are the responsibility of the contractor.

lProducts returned using the advanced replacement process must be received within 30 days of the RMA issue date.

4 Channel NAC Module (S793) Information Guide

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 6

OVERVIEW

4 Channel NAC Module (S793)

The 4 Channel NACpanel modules are typically used in applications that require more than the standard panel

NAC outputs. Each of these modules adds 4 additional supervised NAC outputs, each of which can be

individually programmed.

These modules may be mixed with 16 Channel I/O modules, 8 Channel Conventional Zone modules, or 8

Channel Relay modules to provide a very flexible system of I/O to satisfy almost any requirement. All inputs and

outputs are configurable in the same way as devices connected to the loops and all may contribute to, or be

acted upon, by cause and effect logic.

Package Contents

l(1) Installation sheet

l(1) Wiring Terminal Labels

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 7

4 Channel NAC Module (S793) Information Guide

l(1) S793 4 Channel NAC Panel Module

l(4) End-of-Line Diode (S2029)

4 Channel NAC Module (S793) Information Guide

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 8

INSTALLATION

This section explains the installation procedure for the 4 Channel NAC Panel Module.

qUsing Loop Explorer 2, add the panel module to the existing configuration and configure it as required for the

system. For detailed information on the configuration settings, refer to the Configuration section.

qNotify the monitoring center and location security that the Taktis Fire Alarm ControlPanel will be temporarily out of

service.

qRemove the module from its packaging and check its contents.

qSet the address of the module as configured in Loop Explorer 2. Refer to Setting the Address for details.

qDetermine the slot (D or higher) where the panel module will be installed and place the provided sticker label on the

corresponding field terminals.

qConnect field wiring and install appropriate end-of-line diodes (included with module).

qTransfer the new configuration from Loop Explorer 2 into the panel.

qWait for the "Sending configuration to panel" (in LE2) and "Saving configuration" (on the panel) steps to complete.

qRemove AC and battery power from the panel.

qRemove the black plastic cover.

qInstall the module into selected slot on the Main Back Board or an Extension Board of the panel.

qRestore AC and battery power.

qWait for the panel start-up process to complete. Refer to the Taktis Fire Alarm ControlPanel

InstallationManual (MAN-1431KE) for more information.

qTest communication from the panel via the LEDStatus Indicators

qResolve any troubles related to the new NACs.

qActivate each circuit and verify that all connected devices function properly.

qReplace the black plastic cover.

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 9

4 Channel NAC Module (S793) Information Guide

Install this product in accordance with NFPA 72, the National Electrical Code, and all local codes.

IMPORTANT! The module must be installed by personnel familiar with electronic components. Electronic

components within the module are vulnerable to damage from electrostatic discharge. Ground straps must be worn by

installers before handling to prevent electrostatic discharge damage.

Before You Begin

Before you begin the installation, take a few minutes to review the installation information, gather the required

items, and complete the tasks listed below to make the installation as quick and easy as possible:

1. Acquire the following items that are not included with the 4 Channel NAC Module, but may be required for

installation:

lGround Strap - A ground strap is required for handling circuit boards. The ground strap is not provided in the

packaging of the 4 Channel NAC Module.

Setting the Address

Panel modules should use addresses 1-8. Each panel module of the Taktis Fire Alarm ControlPanel must

contain a unique setting before being connected to the Main Back Board. The binary setting of the DIP switch

sets the specific address for the panel module. The numeric order of the address setting between modules does

not impact operation, but each panel module must be assigned a separate / unique address.

The black portion of the DIP switch identifies the switch actuator.

4 Channel NAC Module (S793) Information Guide

Kentec Electronics Ltd

4 Channel NAC Module (S793) Information Guide

UL Version 1.00 |March 2021 |MAN-1442KE

Page 10

Table des matières

Autres manuels Kentec Electronics Unité de contrôle

Kentec Electronics

Kentec Electronics XT+ Manuel utilisateur

Kentec Electronics

Kentec Electronics Syncro Si Manuel utilisateur

Kentec Electronics

Kentec Electronics S792 Manuel technique

Kentec Electronics

Kentec Electronics 723 Manuel technique

Kentec Electronics

Kentec Electronics Sigma XT Plus Manuel utilisateur

Kentec Electronics

Kentec Electronics XT+ Manuel utilisateur

Kentec Electronics

Kentec Electronics Taktis TRC00NC-10 Manuel technique

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur