Kentec Electronics S792 Manuel technique

8 Channel Conventional Zone

Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

8 Channel Conventional Zone Module (S792) Information Guide

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 2

CONTENTS

Contents 3

Compliance 5

Underwriters Laboratories (UL) 5

FCC 5

Installation 5

Introduction 6

Technical Support 6

Return Material Authorization (RMA) 6

Warranty Service 7

Advanced Replacements 7

Overview 8

Package Contents 8

Installation 10

Before You Begin 11

Setting the Address 11

Placement 11

Wiring 13

Circuit Activation 15

Testing the Installation 16

Configuration 17

ULCompliance Limitations 18

Device Settings / Input Actions 19

Troubleshooting 22

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 3

8 Channel Conventional Zone Module (S792) Information Guide

Specifications 23

Electrical 24

Overall Module Electrical Ratings 24

Initiating Circuit Characteristics 24

Operating Environment 25

Physical Specifications 26

Compatible Devices 26

Apollo 26

System Sensor 26

Hochiki 26

8 Channel Conventional Zone Module (S792) Information Guide

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 4

COMPLIANCE

Underwriters Laboratories (UL)

Fire Alarm Subassembly

Kentec Electronics Ltd

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the Installation Manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense. Any

changes or modifications not expressly approved by Kentec Electronics Ltd could void the user's authority to

operate this equipment under the rules and regulations of the FCC.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

Installation

Install this product in accordance with NFPA 13, NFPA 72, NFPA 70, and NEC 70 and all local codes.

All field wiring should be installed using fire rated cables according to the NFPA 72. Riser conductors shall be

installed in accordance with the survivability from attack by fire requirements in National Fire Alarm Code, NFPA

72, Section 12.3. Riser conductors shall employ either a 2 hour rated cable system, or meet requirements

approved by the AHJ.

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 5

8 Channel Conventional Zone Module (S792) Information Guide

INTRODUCTION

Technical Support

For technical support, contact Kentec Electronics, Ltd at +44 (0)1322 222121 or techsupport@kentec.co.uk.

Prior to contacting technical support, have the following information available:

nProduct part number

nPurchase order or order number

nProduct serial number

nCurrent function of the product

nExpected function of the product

nInstallation of the product

Return Material Authorization (RMA)

Contact Technical Support to obtain an RMAfor any product to be returned. Returns will not be accepted

without an accompanying RMA number. An RMA number is assigned when:

lTech Support acknowledges a possible product failure.

lA product was damaged during shipping

lAn incorrect product was shipped

lAn order was placed using an incorrect part number *

lAn order was placed using an incorrect part quantity *

lAn order is no longer required *

* Restocking fees may apply.

All returned products are tested to confirm operating failures experienced in the field. If the product is found to be

functional, contractors must absorb expenses for return shipping, as well as the cost and shipping of the

advanced replacement product.

Prominently display the RMA number on all packages sent for return.

Ship all return products to:

8 Channel Conventional Zone Module (S792) Information Guide

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 6

Attention: RMA # _____________

Kentec Electronics, Ltd

Units 25-27 Fawkes Avenue

Questor, Dartford

Kent. DA1 1JQ

United Kingdom

Warranty Service

Technical Support can replace or repair a defective product when the original purchase is within the warranty

period defined in the sales contract. Check your contract for more information, or contact your sales

representative about your specific warranty period.

Advanced Replacements

Products that fail to operate in the field can be replaced quickly using the advanced replacement process. The

advanced replacement process is available to all contractors who maintain an acceptable line of credit.

Initiate the advanced replacement process by requesting an RMA number from a Tech Support representative.

Advanced replacements can be shipped to your location when the product is covered under warranty and when

a replacement product is in stock.

lAdvanced replacements can be expedited at the request of the contractor. Shipping costs associated with this

process are the responsibility of the contractor.

lProducts returned using the advanced replacement process must be received within 30 days of the RMA issue date.

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 7

8 Channel Conventional Zone Module (S792) Information Guide

OVERVIEW

8 Channel Conventional Zone Panel Module (S792)

The 8 Channel Conventional Zone Panel Module has 8 supervised detection circuits (Class B). If Class A circuits

are needed, they can be made from Class B circuit pairs (1 & 2, 3 &4, 5 & 6, 7 & 8). Each circuit, regardless of

class, can support up to 20 conventional detectors and approved devices. Individual circuits may be configured

for trigger resistor or short circuit activation. These circuits may be used for any of the standard input actions and

can be configured to contribute to cause and effect logic.

Detector models from Apollo, Hochiki, and System Sensor are compatible for use on these Initiating Device

Circuits. All detectors on a given circuit must be from the same manufacturer. Detectors from these

manufacturers can be mixed between separate circuits as long as each contains detectors from a single

manufacturer.

Package Contents

l(1) Installation sheet

l(1) Wiring Terminal Labels

l(1) S792 8 Channel Conventional Zone Panel Module

l(8) 6.8K Ohm resistor (S2027) End-of-Line devices

8 Channel Conventional Zone Module (S792) Information Guide

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 8

NOTE Activation device: 470 Ohm resistor (S2051) is not included, but can be purchased separately.

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 9

8 Channel Conventional Zone Module (S792) Information Guide

INSTALLATION

This section provides instructions for connecting cables, mounting, and testing the 8 Channel ConventionalZone

Panel Module for installation.

qUsing Loop Explorer 2, add the panel module to the existing configuration and configure it as required for the

system. For detailed information on the configuration settings, refer to the Configuration section.

qNotify the monitoring center and location security that the Taktis Fire Alarm ControlPanel will be temporarily out of

service.

qRemove the module from its packaging and check its contents.

qSet the address of the module as configured in Loop Explorer 2. Refer to Setting the Address for details.

qDetermine the slot (E or higher) where the panel module will be installed and place the provided sticker label on the

corresponding field terminals.

qConnect field wiring. For class B circuits, install appropriate end-of-line resistors (included with module) after the

last device on each circuit.

qTransfer the new configuration from Loop Explorer 2 into the panel.

qWait for the "Sending configuration to panel" (in LE2) and "Saving configuration" (on the panel) steps to complete.

qRemove AC and battery power from the panel.

qRemove the black plastic cover.

qInstall the module into selected slot on the Main Back Board or an Extension Board of the panel.

qRestore AC and battery power.

qWait for the panel start-up process to complete. Refer to the Taktis Fire Alarm ControlPanel

InstallationManual (MAN-1431KE) for more information.

qTest communication from the panel via the LEDStatus Indicators.

qResolve any troubles related to the new field wiring.

qActivate each circuit and verify that all connected devices function properly.

8 Channel Conventional Zone Module (S792) Information Guide

Kentec Electronics Ltd

8 Channel Conventional Zone Module (S792) Information Guide

UL Version 1.00 |March 2021 |MAN-1441KE

Page 10

Table des matières

Autres manuels Kentec Electronics Unité de contrôle

Kentec Electronics

Kentec Electronics Syncro Si Manuel utilisateur

Kentec Electronics

Kentec Electronics XT+ Manuel utilisateur

Kentec Electronics

Kentec Electronics S793 Manuel technique

Kentec Electronics

Kentec Electronics XT+ Manuel utilisateur

Kentec Electronics

Kentec Electronics 723 Manuel technique

Kentec Electronics

Kentec Electronics Taktis TRC00NC-10 Manuel technique

Kentec Electronics

Kentec Electronics Sigma XT Plus Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur