Juniper PTX5000 Manuel utilisateur

PTX5000 Packet Transport Router

Quick Start

September 2017

Part Number: 530-066788

Revision 01

This document describes how to install the Juniper Networks®PTX5000 Packet Transport Router.

Contents Quick Start Description | 3

Step 1: Prepare the Site for the PTX5000 | 4

Rack-Mounting Requirements | 4

Tools Required to Unpack and Install the PTX5000 | 5

Step 2: Unpack the PTX5000 | 6

Step 3: Install the PTX5000 Mounting Hardware | 7

Install the PTX5000 Mounting Hardware for a Four-Post Rack or Cabinet | 7

Install Cage Nuts, If Needed | 7

Install the Four-Post Mounting Shelf and Rear Support Bracket | 9

Remove the Center-Mounting Brackets | 10

Install the PTX5000 Mounting Hardware for an Open-Frame Rack | 11

Install Cage Nuts, If Needed | 11

Install the Open-Frame Rack Mounting Shelf | 13

Step 4: Install the PTX5000 | 14

Step 5: Connect the PTX5000 Grounding Cable | 18

Step 6: Install the Front Door on a PTX5000 | 19

Step 7: Connect External Devices and PIC Cables to the PTX5000 | 19

Connect to a Console or Auxiliary Device | 19

Connect to a Network for Out-of-Band Management | 21

Connect the PIC Cables | 22

Step 8: Connect Power to the PTX5000 Router | 24

Connect Power to the PTX5000 60-A DC Input Power Trays | 24

Connect Power to the PTX5000 120-A DC Input Power Trays | 29

Connect Power to the PTX5000 Three-Phase Delta AC PDUs | 32

Connect Power to the PTX5000 Three-Phase Wye AC PDUs | 36

Connect Power to the PTX5000 High Capacity DC PDUs | 42

Connect Power to the PTX5000 High Capacity Delta AC PDUs | 45

Connect Power to the PTX5000 High Capacity Wye AC PDUs | 52

Connect Power to the PTX5000 High Capacity Single-Phase AC PDUs | 57

Step 9: Power On the PTX5000 | 62

Power On a PTX5000 with 60-A DC PDUs | 62

Power On a PTX5000 with 120-A DC PDUs | 64

Power On a PTX5000 with High Capacity DC PDUs | 66

Power On a PTX5000 with Three-Phase AC PDUs | 68

Power On a PTX5000 with High Capacity Single-Phase AC PDUs | 69

Step 10: Perform the PTX5000 Initial Software Configuration | 71

Enter Configuration Mode | 72

Configure User Accounts and Passwords | 72

Configure System Attributes | 73

Commit the Configuration | 75

Safety Warnings | 76

PTX5000 Compliance Statements for NEBS | 78

Compliance Statements for EMC Requirements | 78

Canada | 79

European Community | 79

Israel | 79

Japan | 79

United States | 80

Junos OS Documentation and Release Notes | 80

Requesting Technical Support | 80

Self-Help Online Tools and Resources | 81

Creating a Service Request with JTAC | 81

Revision History | 81

Quick Start Description

This Quick Start contains information you need to install and configure the PTX5000. For complete

installation instructions, see the PTX5000 Packet Transport Router Hardware Guide at

https://www.juniper.net/documentation/.

WARNING: This Quick Start contains a summary of safety warnings in “Safety Warnings”

on page 76. For a complete list of warnings for the PTX5000, including translations, see

the PTX5000 Packet Transport Router Hardware Guide at

https://www.juniper.net/documentation/.

The PTX5000 router is shipped in a wooden crate. A wooden pallet forms the base of the crate. The chassis

is bolted to this pallet. The shipping crate also contains an accessory box and this Quick Start.

Step 1: Prepare the Site for the PTX5000

IN THIS SECTION

Rack-Mounting Requirements | 4

Tools Required to Unpack and Install the PTX5000 | 5

Before installing the PTX5000, make sure that the site meets all the power, environmental, and clearance

requirements. See the site preparation guidelines in the PTX5000 Packet Transport Router Hardware Guide.

Rack-Mounting Requirements

You can install the PTX5000 in different types of racks, including a four-post rack or cabinet, or an

open-frame rack.

•The rack rails must be spaced widely enough to accommodate the chassis's external dimensions: 62.5 in.

(158.8 cm) high, 33.1 in. (84.1 cm) deep, and 17.5 in. (44.5 cm) wide. The outer edges of the mounting

brackets extend the width to 19 in. (48.3 cm). The front cable management system adds 3.8 in. (9.7 cm)

to the depth. If the front door is used, this adds 5.5 in. (14 cm) to the depth of the chassis. The rear cable

management system adds 5.5 in. (14 cm) to the depth of the chassis.

•The rack must be strong enough to support the weight of the fully configured PTX5000, up to about

1200 lb (544.3 kg).

NOTE: In an open-frame rack, center-mounting is required because the more even distribution

of weight provides greater stability. For center-mounting, you use the mounting brackets attached

to the center of the chassis for rack mounting.

You must allow sufficient clearance around the rack (see Figure 1 on page 5):

•For the cooling system to function properly, the airflow around the chassis must be unrestricted.

NOTE: If you mount the chassis in a cabinet, be sure that ventilation is sufficient to prevent

overheating.

•For service personnel to remove and install hardware components, there must be adequate space at the

front and back of the chassis. At least 24 in. (61.0 cm) are required both in front of and behind the

PTX5000. NEBS GR-63 recommends that you allow at least 30 in. (72.6 cm) behind the rack.

•Additional clearance is required to accommodate the depth of the following components:

•Front cable management system—3.8 in. (9.7 cm) additional depth in the front of the chassis.

•Front door—5.5 in. (14 cm) additional depth in the front of the chassis.

•Rear cable management system—5.5 in. (14 cm) additional depth in the rear of the chassis.

Figure 1: Chassis Dimensions and Clearance Requirements

Tools Required to Unpack and Install the PTX5000

Gather the tools required to unpack the PTX5000:

•Phillips (+) screwdriver, number 2

•1/2-in. or 13-mm open-end or socket wrench to remove bracket bolts from the shipping pallet

•Blank panels to cover any slots not occupied by a component

Gather the tools required to install the PTX5000:

•Mechanical lift

•Phillips (+) screwdriver, number 2

Gather the tools required to ground the PTX5000:

•Grounding cable (which you must provide)

•Grounding lug (depending on your configuration, 0-AWG or 4-AWG (21.2 mm2) cable lugs are supplied

with DC PDUs, and can be used for grounding.)

•M6 screws or UNC 1/4-20 screws

•Electrostatic discharge (ESD) grounding wrist strap

If you have an AC-powered router, gather the tools required to connect the PTX5000 to AC power:

•AC power cords

•Phillips (+) screwdriver, number 2 to access the metal AC wiring compartment and remove or attach the

AC power cord.

•1/5-in. (5.5-mm) slotted screwdriver to attach the ground wire and input terminal wires of the AC power

cord.

If you have a DC-powered router, gather the tools required to connect the PTX5000 to DC power:

•7/16-in. (11-mm) nut driver, with a minimum of 81 lb-in. (9.0 Nm) tightening torque, for tightening nuts

to the terminal studs.

CAUTION: You must use an appropriate torque-controlled tool to tighten the nuts.

Applying excessive torque damages the terminal studs. The maximum torque that may

be applied to this nut is 99 lb-in. (11 Nm).

•Phillips (+) screwdriver, number 2

•DC power cables, which you must provide

•DC power lugs

Step 2: Unpack the PTX5000

For detailed instructions on how to unpack the shipping crate and verifying the parts received, see the

PTX5000 Packet Transport Router Hardware Guide.

Step 3: Install the PTX5000 Mounting Hardware

IN THIS SECTION

Install the PTX5000 Mounting Hardware for a Four-Post Rack or Cabinet | 7

Install the PTX5000 Mounting Hardware for an Open-Frame Rack | 11

To install the mounting hardware, perform one of the following procedures:

Install the PTX5000 Mounting Hardware for a Four-Post Rack or Cabinet

1. Install Cage Nuts, If Needed | 7

2. Install the Four-Post Mounting Shelf and Rear Support Bracket | 9

3. Remove the Center-Mounting Brackets | 10

Install Cage Nuts, If Needed

Insert cage nuts, if needed, into the holes listed in Table 1 on page 8 and Table 2 on page 8 (an X indicates

a mounting hole location). The hole distances are relative to the standard U division on the rack that is

aligned with the bottom of the mounting shelf and rear support bracket.

To install cage nuts in a four-post rack:

1. On the rear rack rails, insert cage nuts in the holes specified for the rear support bracket. Install the

cage nuts in the rear of the rear rail (see Table 1 on page 8).

2. On the front rack rails, insert cage nuts in the holes specified for the four-post mounting shelf. Install

the cage nuts in the front of the front rail (see Table 1 on page 8).

3. On the front rack rails, insert cage nuts in the holes specified for mounting the chassis. Install the cage

nuts in the front of the front rail (see Table 2 on page 8).

Table 1: Mounting Hole Locations for Installing the Four-Post Mounting Shelf and Rear Support Bracket

Rear Support

Bracket

Four-Post Rack

Mounting ShelfDistance Above U DivisionHole

XX1.86 U3.25 in. (8.3 cm)6

XX1.5 U2.63 in. (6.7 cm)5

XX1.14 U2.00 in. (5.1 cm)4

XX0.86 U1.50 in. (3.8 cm)3

XX0.50 U0.88 in. (2.2 cm)2

XX0.14 U0.25 in. (0.6 cm)1

Table 2: Mounting Hole Locations for Installing a PTX5000 in a Four-Post Rack

Distance Above U DivisionHole

36.50 U63.88 in. (162.2 cm)110

33.50 U58.63 in. (148.9 cm)101

30.50 U53.38 in. (135.6 cm)92

27.50 U48.13 in. (122.2 cm)83

24.50 U42.88 in. (108.9 cm)74

21.50 U37.63 in. (95.6 cm)65

18.50 U32.38 in. (82.2 cm)56

15.50 U27.13 in. (68.9 cm)47

12.50 U21.88 in. (55.6 cm)38

9.50 U16.63 in. (42.2 cm)29

6.50 U11.38 in. (28.9 cm)20

3.50 U6.13 in. (15.6 cm)11

The holes in the front-mounting flanges are spaced at 3 U (5.25 in. or 13.3 cm).

Install the Four-Post Mounting Shelf and Rear Support Bracket

To install the four-post mounting shelf and rear support bracket (see Figure 2 on page 10):

1. On the rear of each rear rack rail, partially insert a mounting screw into the lowest hole specified in

Table 1 on page 8.

2. Install the rear support bracket on the rear of the rear rack rails. Rest the bottom slot of the rear support

bracket on a mounting screw. The rear support bracket extends toward the center of the rack.

3. Partially insert screws into the open holes in the rear support bracket.

4. Tighten all the screws completely.

5. On the front of each front rack rail, partially insert a mounting screw into the lowest hole specified in

Table 1 on page 8.

6. Install the four-post rack mounting shelf on the front rack rails. Rest the bottom slot of the front flange

on a mounting screw. Rest the back of the four-post rack mounting shelf on top of the rear support

bracket.

7. Partially insert screws into the open holes in the mounting shelf.

8. Tighten all the screws completely.

9. Fasten the four-post mounting shelf to the rear support bracket by partially inserting the screws provided

in the accessory kit into the open holes on top of the four-post mounting shelf.

NOTE: Several holes are provided on top of the shelf. Two holes on each side of the shelf will

align with the holes in the rear support bracket.

10. Tighten all the screws completely.

Figure 2: Installing the Mounting Hardware for a Four-Post Rack

g006189

2—1—Four-post mounting shelfRear support bracket

Remove the Center-Mounting Brackets

The center-mounting brackets are not used for a four-post rack, and must be removed from the chassis.

To remove the center-mounting brackets from the chassis:

1. Loosen the screws from each bracket (see Figure 3 on page 11).

2. Remove each bracket.

Autres manuels pour PTX5000

Table des matières

Autres manuels Juniper Routeur réseau

Juniper

Juniper ACX2000 Manuel utilisateur

Juniper

Juniper PTX1000 Manuel utilisateur

Juniper

Juniper ACX Series Manuel utilisateur

Juniper

Juniper M10i Instructions d'installation

Juniper

Juniper EX9200 Series Fiche technique

Juniper

Juniper SSR1200 Instructions d'installation

Juniper

Juniper JUNOS J Series Manuel utilisateur

Juniper

Juniper JRR200 Instructions d'installation

Juniper

Juniper MX2010 Manuel utilisateur

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX HARDWARE GUIDE REV... Instructions d'installation

Juniper

Juniper MX104 Instructions d'installation

Juniper

Juniper T4000 - Manuel utilisateur

Juniper

Juniper MX10003 Manuel utilisateur

Juniper

Juniper ACX4000 Instructions d'installation

Juniper

Juniper J2300 Manuel utilisateur

Juniper

Juniper ACX1000 Manuel utilisateur

Juniper

Juniper M120 Instructions d'installation

Juniper

Juniper E320 Manuel utilisateur

Juniper

Juniper MX10004 Manuel utilisateur

Juniper

Juniper T640 Instructions d'installation

Juniper

Juniper EX9200 Series Fiche technique

Juniper

Juniper MX480 Instructions d'installation

Juniper

Juniper M40 Instructions d'installation

Juniper

Juniper JCS 1200 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité