Juniper MX5 Manuel utilisateur

MX5, MX10, MX40, and MX80

3D Universal Edge Router

Quick Start

January 2015

Part Number: 530-062012

Revision 01

This document describes how to install the Juniper Networks®MX5, MX10, MX40, and

MX80 3D Universal Edge Router.

Contents MX5, MX10, MX40, and MX80 Quick Start Description . . . . . . . . . . . . . . . . . . . . . . 3

Step 1: Prepare the Site for MX5, MX10, MX40, or MX80 Installation . . . . . . . . . . . 4

MX5, MX10, MX40, and MX80 Router Rack Requirements . . . . . . . . . . . . . . . . 4

Tools Required to Prepare the MX5, MX10, MX40, and MX80 Router for

Installation ..................................................5

Move the Mounting Brackets for Center-Mounting the MX5, MX10, MX40,

orMX80Router,IfNeeded.....................................5

Step2:InstalltheRouter..............................................7

Tools Required to Install the MX5, MX10, MX40, or MX80 Router . . . . . . . . . . 7

Install the MX5, MX10, MX40, or MX80 Chassis in the Rack . . . . . . . . . . . . . . . 7

Install the MX5, MX10, MX40, or MX80 Cable Management Bracket . . . . . . . 8

Step3:ConnecttheGroundingCable...................................10

Step 4: Connect External Devices and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connect the MX5, MX10, MX40, or MX80 Router to a Network for

Out-of-BandManagement.....................................11

Connect the MX5, MX10, MX40, or MX80 Router to a Management Console

orAuxiliaryDevice............................................11

Connect MIC Cables to the MX5, MX10, MX40, or MX80 Router . . . . . . . . . . . 11

Step5:ConnectPowerCables.........................................13

ConnectPowertoanACRouter....................................13

ConnectPowertoaDCRouter.....................................14

Step 6: Perform Initial Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

EnterConfigurationMode.........................................16

Configure User Accounts and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

ConfigureSystemAttributes.......................................17

CommittheConfiguration.........................................17

SafetyWarnings....................................................19

ComplianceStatementsforNEBS.....................................20

Compliance Statements for EMC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Canada........................................................21

EuropeanCommunity............................................21

Israel..........................................................21

Japan .........................................................21

UnitedStates...................................................22

Junos OS Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

RequestingTechnicalSupport.........................................23

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

OpeningaCasewithJTAC........................................24

Revision History....................................................24

MX5, MX10, MX40, and MX80 3D Universal Edge Router Quick Start

MX5, MX10, MX40, and MX80 Quick Start Description

This Quick Start contains information you need to install and configure the router quickly.

For complete installation instructions, see the MX5, MX10, MX40, and MX80 3D Universal

Edge Router Hardware Guide at http://www.juniper.net/techpubs/.

WARNING: This Quick Start contains a summary of safety warnings in “Safety

Warnings” on page 19. For a complete list of warnings for this router, including

translations, see the MX5, MX10, MX40, and MX80 3D Universal Edge Router

Hardware Guide at http://www.juniper.net/techpubs/.

The MX5, MX10, MX40, and MX80 routers are available as a modular chassis with two

dedicated slots for Modular Interface Cards (MICs) that provide scalable configuration

options. Software licenses allow you to upgrade from one router to another without a

hardware upgrade. The ports are restricted based on the router’s associated license as

follows:

•MX5 router: allows usage of the MIC slot labeled 1/MIC 0 which comes pre-populated

with the Gigabit Ethernet MIC with SFP.

•MX10 router: allows usage of the MIC slot labeled 1/MIC 0 which comes pre-populated

with the Gigabit Ethernet MIC with SFP and the second MIC slot labeled 1/MIC 1.

•MX40 router: allows usage of both MIC slots and ports 0and 1of the built-in 10-Gigabit

Ethernet MIC (labeled 0/MIC 0).

•MX80 router: allows usage of both MIC slots and all four ports of the built-in 10-Gigabit

Ethernet MIC (labeled 0/MIC 0).

A fixed version of the MX80 router (model number: MX80-48T) has 48 fixed

10/100/1000Base-T RJ45 ports in place of the MIC slots.

For a list of MICs supported on the MX5, MX10, MX40, and modular MX80 routers, see

MICs Supported by MX Series Routers in the MX Series Interface Module Reference.

MX5, MX10, MX40, and MX80 Quick Start Description

Step 1: Prepare the Site for MX5, MX10, MX40, or MX80 Installation

•MX5, MX10, MX40, and MX80 Router Rack Requirements on page 4

•Tools Required to Prepare the MX5, MX10, MX40, and MX80 Router for

Installation on page 5

•Move the Mounting Brackets for Center-Mounting the MX5, MX10, MX40, or MX80

Router, If Needed on page 5

MX5, MX10, MX40, and MX80 Router Rack Requirements

•You can install the router in a four-post rack or cabinet or an open-frame rack.

•The rack rails must be spaced widely enough to accommodate the router chassis's

external dimensions: 3.5 in. (8.9 cm) high, 21.75 in. (55.2 cm) deep, and 17.4 in. (44.2 cm)

wide. The outer edges of the mounting brackets extend the width to 19.2 in. (48.7 cm).

•The rack must be strong enough to support the weight of the fully configured router,

up to 30 lb (13.6 kg).

•For the cooling system to function properly, the airflow around the chassis must be

unrestricted. Allow at least 6 in. (15.2 cm) of clearance between side-cooled routers.

Allow 2.8 in. (7 cm) between the side of the chassis and any non-heat-producing

surface such as a wall.

•For service personnel to remove and install hardware components, there must be

adequate space at the front and back of the router. Allow at least 30 in. (76.2 cm) in

front of the router and 24 in. (61 cm) behind the router.

•The rack or cabinet must have an adequate supply of cooling air.

•Ensure that the cabinet allows the chassis hot exhaust air to exit from the cabinet

without recirculating into the router.

•The router must be installed into a rack that is secured to the building structure.

•Mount the router at the bottom of the rack if it is the only unit in the rack.

•When mounting the router in a partially filled rack, load the rack from the bottom to

the top with the heaviest component at the bottom of the rack.

MX5, MX10, MX40, and MX80 3D Universal Edge Router Quick Start

Figure 1: MX5, MX10, MX40, and MX80 Rack Clearance and Router

Dimensions

Rear of chassis

Front of chassis 17.5"

(44.5 cm)

20.2"

(51.3 cm)

g005017

Front-mounting flange

19.2"

(48.7 cm)

24" (61 cm)

clearance required

30" (76.2 cm)

clearance recommended for

maintenance

Cable

management

bracket

23.46"

(59.6cm)

Tools Required to Prepare the MX5, MX10, MX40, and MX80 Router for Installation

•Blank panels to cover any slots not occupied by a component

•Mounting brackets, supplied with the router

•Eight screws for securing the mounting brackets to the chassis, supplied with the router

•Phillips (+) screwdriver, number 2

Move the Mounting Brackets for Center-Mounting the MX5, MX10, MX40, or MX80 Router, If

Needed

Two removable mounting brackets are attached to the mounting holes closest to the

front of the chassis (see Figure 2 on page 6). You can move the pair of brackets to

another position on the side of the chassis for center-mounting the router.

To move the mounting brackets from the front of the chassis toward the center of the

chassis (see Figure 3 on page 6):

1. Remove the four screws at the top and bottom of the bracket.

2. Pull the bracket away from the chassis.

3. Align the bracket with the two sets of mounting holes located toward the center of

the chassis.

4. Insert the four screws at the top and bottom of the bracket and tighten each partially.

5. Tighten the four screws completely.

6. Repeat the procedure for the other bracket.

Tools Required to Prepare the MX5, MX10, MX40, and MX80 Router for Installation

Figure 2: Front-Mount the Brackets on the MX5, MX10, MX40, or MX80

Router

g005018

Figure 3: Center-Mount the Brackets on the MX5, MX10, MX40, or MX80

Router

g005019

MX5, MX10, MX40, and MX80 3D Universal Edge Router Quick Start

Step 2: Install the Router

•Tools Required to Install the MX5, MX10, MX40, or MX80 Router on page 7

•Install the MX5, MX10, MX40, or MX80 Chassis in the Rack on page 7

•Install the MX5, MX10, MX40, or MX80 Cable Management Bracket on page 8

Tools Required to Install the MX5, MX10, MX40, or MX80 Router

To install the router in a rack, you need the following tools:

•Phillips (+) screwdriver, number 2

•ESD grounding wrist strap

•Four mounting screws, supplied with the chassis

•Cable management bracket, supplied with the router

•Two screws for securing the cable management bracket, supplied with the router

Install the MX5, MX10, MX40, or MX80 Chassis in the Rack

Lifting the chassis and mounting it in a rack requires two people. The chassis weighs

approximately 30 lb (13.6 kg).

1. Ensure that the rack is in its permanent location and is secured to the building. Ensure

that the installation site allows adequate clearance for both airflow and maintenance.

2. Position the router in front of the rack or cabinet.

3. With one person on each side, hold onto the bottom of the chassis and carefully lift

it so that the mounting brackets contact the rack rails.

4. Align the mounting brackets with the holes in the rack rails.

5. Install a mounting screw into each of the open mounting holes aligned with the rack,

starting from the bottom.

6. Visually inspect the alignment of the router. If the router is installed properly in the

rack, all the mounting screws on one side of the rack should be aligned with the

mounting screws on the opposite side and the router should be level.

Step 2: Install the Router

Figure 4: Install the Front-Mounted Router in the Rack

Mounting rack

Mounting bracket

g005020

Figure 5: Install the Center-Mounted Router in the Rack

Mounting rack

Mounting bracket

g005044

Install the MX5, MX10, MX40, or MX80 Cable Management Bracket

1. Position the cable management bracket on the left side of the front of the chassis.

2. Tighten the screws at the bottom and top of the bracket.

MX5, MX10, MX40, and MX80 3D Universal Edge Router Quick Start

Figure 6: Install the Cable Management Bracket

g005036

Install the MX5, MX10, MX40, or MX80 Cable Management Bracket

Step 3: Connect the Grounding Cable

You ground the router by connecting a grounding cable to earth ground and then attaching

it to the chassis grounding points using two SAE 10-32 screws. You must provide the

grounding cables (the cable lugs are supplied with the router). To ground the MX5, MX10,

MX40, or MX80 router:

1. Verify that a licensed electrician has attached the cable lug provided with the router

to the grounding cable.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect

the strap to an approved site ESD grounding point. See the instructions for your site.

3. Ensure that all grounding surfaces are clean and brought to a bright finish before

grounding connections are made.

4. Connect the grounding cable to a proper earth ground.

5. Detach the ESD grounding strap from the site ESD grounding point.

6. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the

ESD points on the chassis.

7. Place the grounding cable lug over the grounding points on the upper rear of the

chassis (see Figure 7 on page 10).

8. Secure the grounding cable lug with the screws. The holes are sized for SAE 10-32

screws.

9. Dress the grounding cable and verify that it does not touch or block access to router

components, and that it does not drape where people could trip on it.

Figure 7: Grounding Points on the MX5, MX10, MX40, or MX80 Router

g005009

CLOCK SYNC

Protective

earthing terminal

(grounding points)

MX5, MX10, MX40, and MX80 3D Universal Edge Router Quick Start

Autres manuels pour MX5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Juniper Routeur réseau

Juniper

Juniper ACX1000 Manuel utilisateur

Juniper

Juniper ACX6160 Manuel utilisateur

Juniper

Juniper MX5 Instructions d'installation

Juniper

Juniper T640 Instructions d'installation

Juniper

Juniper LN2600 Manuel utilisateur

Juniper

Juniper PTX5000 Instructions d'installation

Juniper

Juniper MX240 Instructions d'installation

Juniper

Juniper Internet Router M160 Instructions d'installation

Juniper

Juniper Day One+ Manuel utilisateur

Juniper

Juniper T4000 - Instructions d'installation

Juniper

Juniper JCS 1200 Manuel utilisateur

Juniper

Juniper LN2600 Instructions d'installation

Juniper

Juniper PTX10001-36MR Manuel utilisateur

Juniper

Juniper MX Series Manuel utilisateur

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 HARDWARE GUIDE REV... Instructions d'installation

Juniper

Juniper M40 Manuel utilisateur

Juniper

Juniper ACX7100-32C Instructions d'installation

Juniper

Juniper E-Series Instructions d'installation

Juniper

Juniper ACX1000 Manuel utilisateur

Juniper

Juniper PTX10003-160C Manuel utilisateur

Juniper

Juniper QFX5100-48SH Manuel utilisateur

Juniper

Juniper PTX10001-20C Manuel utilisateur

Juniper

Juniper V10000 Manuel utilisateur

Juniper

Juniper JUNOS OS 10.4 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité